Panasonic Network Camera Wv Sc386 Installation Guide

AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT 
PORTFOLIO LICENSE FOR THE PERSONAL USE OF A 
CONSUMER OR OTHER USES IN WHICH IT DOES NOT 
RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN 
COMPLIANCE WITH THE AVC STANDARD ("AVC 
VIDEO") AND/OR (ii) DECODE AVC VIDEO THAT WAS 
ENCODED BY A CONSUMER ENGAGED IN A 
PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A 
VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. 
NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR 
ANY OTHER USE. ADDITIONAL...

Precautions for installation
This product is designed to be used as a pendant 
mount camera.
When using after installing it tilted or on desktop, it may 
not work correctly or its lifetime may be shorten.
Installing place
Contact your dealer for assistance if you are unsure of an 
appropriate place in your particular environment.
	 •	 Make	 sure	 that	 the	 installation	 area	 is	 strong	 enough	to hold this product, such as a concrete ceiling.
	 •	 When	 the	 installation	 area	 is	 not	 strong	 enough,...

Major operating controls

    
Camera mount bracket (accessory)Safety wire
(fixed with the mount bracket)Decorative cover (accessory)
Camera
Dome cover
* Handle the dome cover with extra care 
  since it is easy to be scratched.
SDHC/SD memory card slot cover
Live indicator
SDHC/SD memory card slot
Dome INITIAL SET button
13 

About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this button, and wait fo\
r 
around 5 seconds or more without releasing this button. Wait around 3 minute after releasing the button. The camera will 
start up and the settings including the network settings will be initial\
ized. Before initializing the settings, it is recommended 
to write down the settings in advance. The initialization will be complete when the live indicator...

Installations/Connections
The following are descriptions of how to install the camera on a ceiling. 
Before starting the installation/connection, prepare the required devices and cables.
Before starting the connection, turn off the power of the devices including the camera and the PC or disconnect\
 from the 
12 V DC power supply.
When installing the camera with using the ceiling mount bracket, the cei\
ling embedding bracket, or the wall mount bracket, 
refer to the instructions included with those...

Wire through a hole in the ceiling
    
Step 1
Fix the camera mount bracket (accessory) with four 
optional fixing screws (M4, option).
There should be no obstacles such as wall in a range of 
100 mm {3-15/16  inches} away from the center point of 
the camera mount bracket.
Shooting direction (FRONT)
83.5 mm 
{3-9/32 inches}
46 mm 
{1-13/16 inches}
100 mm {3-15/16 inches} or more 
away from obstacles such as wall
Step 2
Make a hole in the ceiling to pass the cables through.
Make a hole 25 mm {31/32...

Specification of cable (wire):  AWG #22 - #28,  Single core, twisted
IMPORTANT:
	 •	 Do	not	connect	2	wires	or	more	directly	to	a	terminal.	 When it is necessary to connect 2 or more wires, use 
a splitter.
	 •	 Input	 and	 output	 of	 the	 external	 I/O	 terminal	 2	 and	 3	 can be switched by configuring the setting. Refer to 
the Operating Instructions (included in the CD-ROM) 
for further information about the EXT I/O terminal 2 
and 3 (ALARM IN2, 3) settings ("Off", "Alarm input",...

Center of the 
camera mount bracket
Guide part Lock plate
Camera mount bracket (accessory)
Rotate
Main body 
of the 
camera
20 °
IMPORTANT:
	 •	 When	 mounting	 the	 camera	 onto	 the	 camera	 mount	 bracket, hold the main body of the camera. Mounting 
the camera while holding the dome cover may result 
in malfunction.
 
Step 7
Fix the camera on the camera mount bracket (accessory) 
using the camera fixing screw (M3, accessory).
Recommended tightening torque: 0.68 N·m {0.50 lbf·ft}
    
Step 8
Connect...

• 12 V DC power supply terminal
 q  Loosen the screw of the power cable plug (accesso-
ry).
  w  Connect the output cable to the power cable plug. 
   Strip 3 mm to 7 mm {1/8  inches to 9/32 inches} from 
the end of the wire, and twist the stripped part of the 
wire sufficiently to avoid short circuit. 
Specification of cable (wire):  16 AWG - 24 AWG, Single core, twisted
  *  Check whether the stripped part of the wire is not 
exposed and is securely connected.
  e  Tighten the screw of the power cable...

 e  Fix the decorative cover.
	 •	 Press	the	decorative	cover	to	the	ceiling	with	force.Wire without making a hole in the 
ceiling
    
Step 1
Install the camera by following step 1 and steps 3 - 8 of the 
"
Wire through a hole in the ceiling" section (☞ pages 16 - 19). 
It is unnecessary to make a hole in the ceiling as described in 
step 
2 of the "Wire through a hole in the ceiling" section.
Step 2
Remove the cutout part on the decorative cover (accessory).
Attach the decorative cover...