Home
>
Panasonic
>
Recorder
>
Panasonic Network Camera Recorder With Viewer Software BB-HNP15A Operating Instructions
Panasonic Network Camera Recorder With Viewer Software BB-HNP15A Operating Instructions
Here you can view all the pages of manual Panasonic Network Camera Recorder With Viewer Software BB-HNP15A Operating Instructions. The Panasonic manuals for Recorder are available online for free. You can easily download all the documents as PDF.
Page 31
![Page 31
Operating Instructions
31
[Disabling a monitoring area]
You can specify an area of the image in which to disable motion detection.
To specify a disabled area, click the cells that you want to disable in the motion
detection monitoring window. Disabled areas are darkened. You can set multiple
disabled areas.
\
[Re-enabling a disabled area]
You can re-enable a disabled area by clicking the cells in the disabled area.
Note
If you set the date and time to be displayed on the camera images, disable the...](http://img.usermanuals.tech/thumb/58/74552/w300_bb-hnp15_en_om_d-30.png "Page 31
Operating Instructions
31
[Disabling a monitoring area]
You can specify an area of the image in which to disable motion detection.
To specify a disabled area, click the cells that you want to disable in the motion
detection monitoring window. Disabled areas are darkened. You can set multiple
disabled areas.
\
[Re-enabling a disabled area]
You can re-enable a disabled area by clicking the cells in the disabled area.
Note
If you set the date and time to be displayed on the camera images, disable the...")
Operating Instructions 31 [Disabling a monitoring area] You can specify an area of the image in which to disable motion detection. To specify a disabled area, click the cells that you want to disable in the motion detection monitoring window. Disabled areas are darkened. You can set multiple disabled areas. \ [Re-enabling a disabled area] You can re-enable a disabled area by clicking the cells in the disabled area. Note If you set the date and time to be displayed on the camera images, disable the...
Page 32
Operating Instructions 32 Setting the alarm/sensor detection method You can set an alarm/sensor detection method for cameras that have an alarm/ sensor attached. Alarm/sensor recording can only be enabled for cameras set to the JPEG format (see page 25). If the camera is set to MPEG-4 format, change the setting to JPEG format, then configure the alarm/sensor. Alarm/Sensor Page SettingDescription Set the Alarm1/ Sensor Recording / Set the Alarm2 RecordingAfter you select the check box, recording...
Page 33
![Page 33
Operating Instructions
33
Note
Configure alarm/sensor detection after an alarm/sensor has been attached to
the camera.
Setting alarm/sensor detection without an alarm/sensor causes a malfunction.
Alarm enable
conditionSpecify Alarm enable condition ([Status: Open (High)], [Status:
GND], [Rising : GND to Open (High)] , [Falling : Open (High) to
GND], [Rising and Falling]).
Specify the alarm enable condition after checking the alarm
specification.
[Rising : GND to Open (High)] is selected...](http://img.usermanuals.tech/thumb/58/74552/w300_bb-hnp15_en_om_d-32.png "Page 33
Operating Instructions
33
Note
Configure alarm/sensor detection after an alarm/sensor has been attached to
the camera.
Setting alarm/sensor detection without an alarm/sensor causes a malfunction.
Alarm enable
conditionSpecify Alarm enable condition ([Status: Open (High)], [Status:
GND], [Rising : GND to Open (High)] , [Falling : Open (High) to
GND], [Rising and Falling]).
Specify the alarm enable condition after checking the alarm
specification.
[Rising : GND to Open (High)] is selected...")
Operating Instructions 33 Note Configure alarm/sensor detection after an alarm/sensor has been attached to the camera. Setting alarm/sensor detection without an alarm/sensor causes a malfunction. Alarm enable conditionSpecify Alarm enable condition ([Status: Open (High)], [Status: GND], [Rising : GND to Open (High)] , [Falling : Open (High) to GND], [Rising and Falling]). Specify the alarm enable condition after checking the alarm specification. [Rising : GND to Open (High)] is selected...
Page 34
Operating Instructions 34 Configure commands to execute for detection You can specify executing commands for motion detection and/or alarm detection. Specify the commands in their respecti ve pages when you execute the commands specified (see page 30, 33, 62). Detection Commands Page * The Beep program is installed with this software. Beep 1000 1000 is a command that make s a beeping sound at 1000 Hz for 1000 ms. You can set user created commands as well. However, depending on the commands...
Page 35
![Page 35
Operating Instructions
35
affected. Use optional commands after thorough testing. Recorded image quality
cannot be guaranteed when using optional commands.
[About Commands for Camera External Output Settings]
Unlocking timeUnlocking time
Execute Commands for Camera External Output Unlocking
Execute Commands for Camera External Output Settings
When you set external output unlocking
(After 5 seconds from motion detection, alarm detection, or unlocking time)
Unlock the external output at the set time....](http://img.usermanuals.tech/thumb/58/74552/w300_bb-hnp15_en_om_d-34.png "Page 35
Operating Instructions
35
affected. Use optional commands after thorough testing. Recorded image quality
cannot be guaranteed when using optional commands.
[About Commands for Camera External Output Settings]
Unlocking timeUnlocking time
Execute Commands for Camera External Output Unlocking
Execute Commands for Camera External Output Settings
When you set external output unlocking
(After 5 seconds from motion detection, alarm detection, or unlocking time)
Unlock the external output at the set time....")
Operating Instructions 35 affected. Use optional commands after thorough testing. Recorded image quality cannot be guaranteed when using optional commands. [About Commands for Camera External Output Settings] Unlocking timeUnlocking time Execute Commands for Camera External Output Unlocking Execute Commands for Camera External Output Settings When you set external output unlocking (After 5 seconds from motion detection, alarm detection, or unlocking time) Unlock the external output at the set time....
Page 36
![Page 36
Operating Instructions
36
[About Command Execution]
If you do not select Perform the following control when issuing a
command in Controlling Command Execution. (After 5 seconds from motion detection, alarm detection)
Execute commands for each detection.
Execute commands
When you select Perform the following control when issuing a command
Execute a command only once at the start of recording
(After 5 seconds from motion detection, alarm detection)
Execute commands only at the start of decetion...](http://img.usermanuals.tech/thumb/58/74552/w300_bb-hnp15_en_om_d-35.png "Page 36
Operating Instructions
36
[About Command Execution]
If you do not select Perform the following control when issuing a
command in Controlling Command Execution. (After 5 seconds from motion detection, alarm detection)
Execute commands for each detection.
Execute commands
When you select Perform the following control when issuing a command
Execute a command only once at the start of recording
(After 5 seconds from motion detection, alarm detection)
Execute commands only at the start of decetion...")
Operating Instructions
36
[About Command Execution]
If you do not select Perform the following control when issuing a
command in Controlling Command Execution. (After 5 seconds from motion detection, alarm detection)
Execute commands for each detection.
Execute commands
When you select Perform the following control when issuing a command
Execute a command only once at the start of recording
(After 5 seconds from motion detection, alarm detection)
Execute commands only at the start of decetion...
Page 37
Operating Instructions 37 Adding a keyword to recorded images You can assign keywords to manually recorded images. You can use keywords to search recorded images. Keyword Page1 SettingDescription Keyword1/ Keyword2Put a keyword to recorded images. Maximum 40 characters. 2 keywords (Keyword1/Keyword2) can be set.
Page 38
![Page 38
Operating Instructions
38
2.2 Network Camera Recorder Window
2.2.1 About the Application Windows
Full screen mode and Window mode
You can change the window display between full screen mode (expanding the
window over the entire desktop) or window mode (always displaying the title bar,
menu bar and toolbar).
1.Select [Display Mode] [Full Screen Mode] or [Window Mode] on the menu
bar.
Full screen mode
Window mode
Sliding window
(See page 49)
The toolbar is displayed
when the mouse is
moved upward....](http://img.usermanuals.tech/thumb/58/74552/w300_bb-hnp15_en_om_d-37.png "Page 38
Operating Instructions
38
2.2 Network Camera Recorder Window
2.2.1 About the Application Windows
Full screen mode and Window mode
You can change the window display between full screen mode (expanding the
window over the entire desktop) or window mode (always displaying the title bar,
menu bar and toolbar).
1.Select [Display Mode] [Full Screen Mode] or [Window Mode] on the menu
bar.
Full screen mode
Window mode
Sliding window
(See page 49)
The toolbar is displayed
when the mouse is
moved upward....")
Operating Instructions 38 2.2 Network Camera Recorder Window 2.2.1 About the Application Windows Full screen mode and Window mode You can change the window display between full screen mode (expanding the window over the entire desktop) or window mode (always displaying the title bar, menu bar and toolbar). 1.Select [Display Mode] [Full Screen Mode] or [Window Mode] on the menu bar. Full screen mode Window mode Sliding window (See page 49) The toolbar is displayed when the mouse is moved upward....
Page 39
![Page 39
Operating Instructions
39
Multi-Monitoring Page
The images from registered cameras are displayed in the multi-monitoring page
(see
page 50).
1.Select [Window] [Multi-Monitoring] on the menu bar.
You can change the number of camera screens to display (see page 79).
Default is four-screen layout (2 rows x 2 columns).
You can rearrange the order of camera screens (see page 85) and enlarge
a camera display area (see page 81).
Note
If you double-click a cameras image on the multi-monitoring page,...](http://img.usermanuals.tech/thumb/58/74552/w300_bb-hnp15_en_om_d-38.png "Page 39
Operating Instructions
39
Multi-Monitoring Page
The images from registered cameras are displayed in the multi-monitoring page
(see
page 50).
1.Select [Window] [Multi-Monitoring] on the menu bar.
You can change the number of camera screens to display (see page 79).
Default is four-screen layout (2 rows x 2 columns).
You can rearrange the order of camera screens (see page 85) and enlarge
a camera display area (see page 81).
Note
If you double-click a cameras image on the multi-monitoring page,...")
Operating Instructions 39 Multi-Monitoring Page The images from registered cameras are displayed in the multi-monitoring page (see page 50). 1.Select [Window] [Multi-Monitoring] on the menu bar. You can change the number of camera screens to display (see page 79). Default is four-screen layout (2 rows x 2 columns). You can rearrange the order of camera screens (see page 85) and enlarge a camera display area (see page 81). Note If you double-click a cameras image on the multi-monitoring page,...
Page 40
![Page 40
Operating Instructions
40
Single-Monitoring Page
In the single-monitoring page, a single image from the focus camera is displayed.
1.Select [Window] [Single-Monitoring] on the menu bar.
A single image from the focus camera is displayed.
Note
If you double-click a cameras image on the multi-monitoring page, the
display will switch to the single-monitoring page. When you double-click on
the single-monitoring page, the display will return to the multi-monitoring
page.
If the click to center...](http://img.usermanuals.tech/thumb/58/74552/w300_bb-hnp15_en_om_d-39.png "Page 40
Operating Instructions
40
Single-Monitoring Page
In the single-monitoring page, a single image from the focus camera is displayed.
1.Select [Window] [Single-Monitoring] on the menu bar.
A single image from the focus camera is displayed.
Note
If you double-click a cameras image on the multi-monitoring page, the
display will switch to the single-monitoring page. When you double-click on
the single-monitoring page, the display will return to the multi-monitoring
page.
If the click to center...")
Operating Instructions 40 Single-Monitoring Page In the single-monitoring page, a single image from the focus camera is displayed. 1.Select [Window] [Single-Monitoring] on the menu bar. A single image from the focus camera is displayed. Note If you double-click a cameras image on the multi-monitoring page, the display will switch to the single-monitoring page. When you double-click on the single-monitoring page, the display will return to the multi-monitoring page. If the click to center...