Panasonic Network Camera Kx Hcm230 Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 91
Section4
Technical Guides 
						

							Operating Instructions
92
4.1 Network Camera Installation
Network Camera has a splash resistant body. The splash resistant body allows
Network Camera to be used indoors and outdoors. Waterproof cabling is
necessary for outdoor mounting. Check Network Camera operation before
installing (cabling and mounting) Network Camera.
Notes
 Install Network Camera under eaves to protect it from direct sunlight.
Prolonged exposure to direct sunlight or halogen light may damage the CMOS
sensor.
 Use the Sunshade in any conditions.
 DonotinstallNetworkCamerainthelocationwhereseabreezesmayhitthe
unit directly.
 Avoid laying Ethernet cable underground or stringing it in the air. Lightning may
cause serious damage to Network Camera or the connected devices.
 AC adaptor is not waterproofed. Put the AC adaptor inside the outdoor power
equipment near Network Camera and protect the AC adaptor from the rain.
Ask the authorized electric wiring dealer.
 AC adaptor cord and Ethernet cable should be waterproofed. Do the
waterproof electric wiring work.
 Do not expose the AC adaptor to the temperatures below -20 °C (-4 °F) or
above +50 °C (122 °F). AC adaptor cannot be operated under these
circumstances.
 Lightning can cause serious permanent damage to Network Camera. Be sure
that Network Camera is grounded in accordance with local electrical codes for
your specific application.
 If Network Camera is used outdoors, the Rubber Cap must be installed in the
CLEAR SETTING button hole. It protects Network Cameras internal
components from moisture damage. Carefully insert the Rubber Cap into the
hole, gently pressing it into place using the end of the long tool. In order for it
to work properly the cap must be seated correctly and fit snug.
 If Network Camera is positioned facing direct sunlight it is possible that a faint
rainbow lens flare may be visible on the image. Sunshade acts similar to a
lens shade on a 35-mm camera. In most cases the Sunshade will minimize the
rainbow lens flare. Repositioning Network Camera so it does not face directly
in the direction of the sun can further improve the image quality. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 93
4.1.1 Network Camera Cabling
Check the location where Network Camera should be installed. Select the proper
cable suited to Network Camera location. Consult an authorized wiring electrician
for cabling.
1.Put the cables through the Connector Cover(1.). Connect the DC plug of the
AC adaptor to the DC IN jack(2.)and Category 5 straight/cross cable to the
Ethernet port(3.). Connect the AC plug of the AC adaptor to the power outlet
(4.).
Notes
 Mounting and cabling instructions described in this Operating
Instructions follow generally accepted guidelines suitable for residential
installations. In some areas, commercial and industrial installations are
regulated by local or state ordinances. For such installations, contact
your local building department or building inspector for more details.
 External I/O and Ground should be threaded through Connector Cover.
Once you putty the cables, External I/O and Ground cannot be
connected until you take the putty off.
 Check the location of Network Camera, the type and the length of the
Ethernet cable (Max. 100 m [330 feet]). Use an Ethernet cable as short
as possible for outdoor use. Lightning may cause serious damage to
Network Camera or the connected devices.
 Use a category 5 cross cable when connecting directly to a PC.
To NetworkDC IN
jack
Ethernet
portDC Plug
Connector
Cover
(3.)
(2.)
(1.)
(4.)
Category 5 straight/cross cable
AC adaptor
Power
Outlet 
						

							Operating Instructions
94
2.Thread the AC adaptor cord through the hook. Put the Rubber Cap and the
Connector Cover by fastening the three screws in numerical order. The
remaining screw hole on the Connector Cover is used for attaching Sunshade.
Note
Be sure to thread the AC adaptor cord through the hook.
3.Attach the Sunshade by fastening the two screws.
Connector Cover
HookAC
adaptor
cord
1
2
3
Carefully insert the
Rubber Cap into the
hole, gently pressing
it into place using
the end of the
long tool. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 95
4.Roll up three putties around the cables and fit them into the holes to prevent
water from getting inside Network Camera. Use last putty to fix the spot.
Notes
 Confirm Network Camera is functioning before puttying the cables. Putties
and Self Bonding tape cannot be used twice.
 Check the length and the type of the Ethernet cable before fixing with putty.
5.Cover the putties by rolling.
 Self Bonding tape is used to mount Network Camera on a wall or ceiling,
so leave half the Self Bonding tape.
6.Connect the Ethernet cable to the Ethernet port of hub, router and PC.
Three puttiesLast putty
Seal cables with
Self Bonding tape.
Do not cover
the ventilation hole.
5 –10 mm
(0.2–0.4 inches) 
						

							Operating Instructions
96
4.1.2 Network Camera Mounting
Four mounting methods are shown in the following figures. Confirm the top and
bottom of Network Camera when mounting. Ask the authorized dealer for
mounting.
Note
Mounting and cabling instructions described in this Operating Instructions
follow generally accepted guidelines suitable for residential installations. In
some areas, commercial and industrial installations are regulated by local or
state ordinances. For such installations, contact your local building department
or building inspector for more details.
Flexible Stand Mounting
Tripod Mounting
Attach Network Camera to the tripod using the tripod bolt. 1) Attach Network Camera by screwing the threaded mount into the tripod
mounting hole.
2) TurnthegriptofixtheFlexibleStandfirmly.
1)
2)
Tripod
mounting
hole
Tripod
mounting
hole 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 97
Wall Mounting
1) Mount the Flexible Stand firmly to a wall or beam using the three
screws (accessories). Set the Flexible Stand 165 mm (6.5 inches) away
from the ceiling.
 Use appropriate screws suited for the material of the wall.
2) Attach Network Camera by screwing the threaded mount into the tripod
mounting hole. A mounting hole on the rear side is also available.
3) Adjust the position of Network Camera and secure the Flexible Stand
firmly.
4) Roll up the cables and Flexible Stand with the Self Bonding tape
(accessories). Refer to page 92 for waterproofing the cables.
1) 2)
3) 4)
Caulk around Flexible
Stand if necessary.
Self Bonding tape
Waterproof the rest
of the cable.
165 mm
(6.5 inches) 
						

							Operating Instructions
98
Ceiling Mounting
1) Mount the Flexible Stand firmly to the ceiling or beam using the three
screws (accessories).
 Use appropriate screws suited for the material of the ceiling.
2) Attach Network Camera by screwing the threaded mount into the tripod
mounting hole.
3) Adjust the position of Network Camera and secure the Flexible Stand
firmly.
4) Roll up the cables and Flexible Stand with the Self Bonding tape
(accessories). Refer to page 92 for waterproofing the cables.
1)
3) 4)2)
Caulk around
Flexible Stand
if necessary.
Self Bonding
tape
Waterproof
the rest
of the cable. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 99
Note
Make sure the Indicator is always in the upper right corner when you mount
Network Camera.
CAUTION
Drive mounting screws into the wall. Be careful to avoid touching any
metalwork (metal/wire laths etc.), conduits or electrical cables buried in the
wall.
top
bottomtop
top
bottom
bottom
Ceiling Mounting
Wall MountingFlexible Stand Mounting
top
bottom 
						

							Operating Instructions
100
Making holes on mortar wall
1.Put Flexible Stand on the wall where you plan to install Network Camera and
mark the points where you are going to make holes.
2.Make holes with an electric drill. Insert plastic plugs (customer provided) into
the holes and push them inside the holes with the hammer.
Note
Mortar wall is easy to come off in drilling.
3.Mount the Flexible Stand by using the screws (accessories).
Change the drill depending on the
concrete wall or the tiled wall.Caulk around the holes
if necessary. Plastic Plug
Hammer