Panasonic Network Camera Kx Hcm110a Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 131
4.Click [Save] when finished.
 New settings are saved.
 The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday.
SettingDescription
Enable Check the box to enable the setting. Clear the box to 
disable it.
A day of the 
week Check the box to enable the day. Clear the box to disable it.
Operation Time Select the [Always] option when you do not specify the time 
period. If you specify the time period, select the time period 
option and set the time period. 
						

							Operating Instructions
132
2.25 Controlling External Output Terminal
The digital output terminal allows you to control the external devices. You can 
change the initial status of the output signal.
Note
Connect the external devices to the camera.
1.Click [External Output] on the Setup page.
2.Click [Save] when finished.
 Clicking [Cancel] cancels your settings without saving changes.
 New settings are saved.
 When finished, Success! is displayed. 
3.Click [Go to External Output Control page].
 The External Output Control page is displayed.
SettingDescription
External Device 
Control Output If you check [Open], the internal transistor turns off and the 
external output terminal gets high impedance (open 
collector) when the camera powers up. If you check [Short 
to GND], the internal transistor turns on and is electrically 
short-circuited to GND pin when the camera powers up. 
The external output terminal gets low impedance (0 V). 
Button name 
modification You can change the output control button names on the 
operation bar. You can name the button depending on your 
external devices. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 133
2.26 Changing Indicator Display
The Indicator Control page allows you to select Indicator operation. Indicator has 
three options.
Always on
 Turn the indicator on when the camera is accessed.
Always off
1.Click [Indicator Control] on the Setup page.
2.Select indicator option.
 Clicking [Cancel] cancels your settings without saving changes.
Note
 See page 7 for indicator display.
 Selecting [Never turn indicator on] keeps indicator always off.
3.Click [Save] when finished.
 New settings are saved.
 When finished, Success! is displayed. 
4.Click [Go to Indicator Control page].
 The Indicator Control page is displayed. 
						

							Operating Instructions
134
3 Camera Maintenance
3.1 Maintenance page
Maintenance
(1)StatusDisplays the camera settings and status (see page 135).
(2)Session StatusDisplays information on access to the camera (see page 
135).
(3)Alarm LogDisplays alarm logs (see page 136).
(4)RestartRestarts the camera (see page 136).
(5)Update FirmwareUpdates the camera firmware (see page 137).
(6)Save SettingsCreates a configuration file (see page 140).
(7)Load SettingsLoads settings from a configuration file (see page 141).
(8)Reset to Factory 
DefaultResets the camera to its default settings (see page 142).
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 135
3.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
See Panasonic Network Camera support website at http://panasonic.co.jp/
pcc/products/en/netwkcam/ for details about status information.
3.1.2 Confirming Session Status
Displays client information connecting to camera.
Clicking [Session Status] displays the following page. 
						

							Operating Instructions
136
3.1.3 Displaying Alarm Logs
Displays up to 50 Alarm Logs in order of time. Old logs will be overwritten by new 
one.
1.Click [Alarm Log] on Maintenance page.
2.Alarm Logs are displayed.
Note
If the camera is restarted, all alarm logs are deleted.
3.1.4 Restarting the Camera
The Restart page can restart the camera. The camera restarts by disconnecting 
the power cord from the outlet and reconnecting it again.
Note
When the camera restarts, the buffered images and alarm logs will be deleted.
1.Click [Restart] on the Maintenance page.
2.Click [Restart].
 Restarting takes about 1 minute. The Top page is displayed when finished.
ItemDescription
New Alarm Logs Displays the number of new alarm logs.
Date Displays the date and time when the Alarm 1, 2, or Motion 
Detect were responded.
Sensor Type Displays the Trigger Setting (Alarm 1, 2, or Motion 
Detection) on the Trigger page.
Signal Type Displays the Alarm enable condition on the Trigger page 
when selected Alarm 1 or 2. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 137
3.1.5 Updating the Camera Firmware
The Update Firmware page allows you to update the camera firmware. If the new 
firmware is available, install it into the camera.
Note
 Do not turn off the power during firmware update.
 All buffered images and alarm logs on the internal memory will be deleted 
after the firmware update.
 The firmware version is displayed on the Top page and the Status page. 
1.Download the new firmware on the Panasonic Network Camera support 
website at http://panasonic.co.jp/pcc/products/en/netwkcam/, and save it 
on your PC.
2.Click [Update Firmware] on the Maintenance page.
3.Click [Update Firmware].
 The camera restarts. 
						

							Operating Instructions
138
 The Update page is displayed in about 1 minute.
4.Click [Browse...].
 A dialog box is displayed to select the firmware.
5.Select the firmware (including directory information) and click [Open].
 The firmware file name is displayed.
6.Confirm the firmware file name, and click [Update Firmware].
 Clicking [Cancel] takes you back to the Top page without firmware update.
 The next message is displayed during update.
 The camera restarts automatically after update.
 The Top page is displayed in about 1 minute. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 139
7.Confirm that the version number on the Top page is updated.
 If the version number is updated, the firmware update is complete.
Updated version 
						

							Operating Instructions
140
3.1.6 Creating Configuration File
A configuration file can be saved on your PC. You can load the camera settings 
from the configuration file on the Load Settings page (see page 
141).
Note
The saved image has privacy information. Prevent private information leaks.
1.Click [Save Settings] on the Maintenance page.
2.Click [Save].
3.Click [Save] on the File Download dialog box.
4.Specify the location, and click [Save] on the Save As dialog box.
 The configuration file is saved in the location.
Note
 The file extension (.dat) cannot be changed. If you change it, the settings 
cannot be loaded.
 If you try to update the camera, create a configuration file after updating 
the firmware. If there is a firmware version difference between the camera 
that you create a configuration file from and the camera that you try to load 
settings to, the settings may not be loaded to the camera.