Panasonic Network Camera Bl C1a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 91
3.Click [Save] when finished.
 The new settings are saved.
 When finished, Success! is displayed.
4.Click [Go to Image Display page].
 The Image Display page is displayed.
Banner DisplayWhen checked to [Enable], the setting will be enabled. 
When unchecked, the setting will be disabled.
Note
 When the Banner Display is enabled, the camera 
accesses the Image URL every time the Single 
Camera page is displayed. The intermittent...

Operating Instructions
92
5.2 Configuring Multiple Cameras
The Multi-Camera Setup page allows you to configure camera IP addresses and 
camera names to view multiple images on the Multi-Camera page. These 
configurations are required to use the Multi-Camera page. Up to 12 cameras can 
be configured. The Selfcamera is registered at No. 1 by default.
1.Click [Multi-Camera] on the Setup page.
2.Click Add.
Note
 If you click the camera number, the modification page is displayed. 
Camera settings can be...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 93
Note
 If your camera will only be accessed on your local network, use each 
cameras local IP address and port number.
 If you intend to access your camera from the Internet, you must use each 
cameras host name (global IP address) and the port number.
4.Click [Save] when finished.
 The new settings are saved.
 The Multi-Camera Setup page is displayed.
SettingDescription
Display Check this box to enable the camera.
IP Address*1...

Operating Instructions
94
5.3 Specifying Operation Time
The Operation Time page allows you to limit the time that the camera is in use. The 
camera image turns to a gray screen outside operation time.
Note
 Your privacy may be compromised if the time period is set incorrectly. 
Confirm the time period after the setup.
 If you access the camera as an administrator, you can view the image 
outside the time period.
1.Click [Operation Time] on the Setup page.
2.Click a No. to set the operation time.
Note...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 95
4.Click [Save] when finished.
 The new settings are saved.
 The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday.
SettingDescription
Enable Check the box to enable the setting. Uncheck the...

Operating Instructions
96
5.4 Changing the Indicator Display
The Indicator Control page allows you to select an operation for the indicator. There 
are three options.
 Turn indicator on when camera is on.
 Turn indicator on during camera access.
 Never turn indicator on.
1.Click [Indicator Control] on the Setup page.
2.Select an option.
 Clicking [Cancel] cancels your settings without saving changes.
Note
 See page 4 for the Indicator Display table.
 Selecting [Never turn indicator on] keeps...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 97
6 Camera Maintenance
6.1 Maintenance page
Maintenance
(1)StatusDisplays the camera settings and status (see page 98).
(2)[For BL-C20A] 
Wireless StatusDisplays wireless information (see page 98).
(3)Session StatusDisplays information on access to the camera (see page 
98).
(4)Sensor LogDisplays sensor logs (see page 99).
(5)RestartRestarts the camera (see page 99).
(6)Update FirmwareUpdates the camera firmware (see page 100).
(7)Save...

Operating Instructions
98
6.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
See the Panasonic Network Camera support website at http://
panasonic.co.jp/pcc/products/en/netwkcam/ for details about status 
information.
6.1.2 [For BL-C20A] Confirming the Wireless Status
The Wireless Status page allows you to check the status of the wireless 
connection....

Operating Instructions
[For assistance, please call: 1-800-272-7033] 99
6.1.4 Confirming Sensor Logs
Displays up to 50 Sensor Logs in chronological order. Old logs will be overwritten 
by new ones.
1.Click [Sensor Log] on the Maintenance page.
2.Sensor Logs are displayed.
Note
If the camera is restarted, all sensor logs are deleted.
6.1.5 Restarting the Camera
It is possible to restart the camera by disconnecting the AC adaptor from the outlet 
and reconnecting it again. The camera can also be restarted...

Operating Instructions
100
6.1.6 Updating the Camera Firmware
The Update Firmware page allows you to update the cameras firmware. If new 
firmware is available, install it into the camera.
Note
 Do not turn off the power during a firmware update.
 All buffered images and sensor logs on the internal memory will be 
deleted after the firmware update.
 The firmware version is displayed on the Top page and the Status page. 
1.Download the new firmware from the Panasonic Network Camera support 
website at...