Panasonic Network Camera Bb Hce481a Operating Instructions

Operating Instructions
161
6.1.7 Loading Settings from a Configuration File
Camera settings can be loaded from a configuration file. If you reset the camera to 
factory default, the camera can load previously used settings from a configuration 
file.
Note
 The configuration file also saves network settings. When settings are loaded, 
the network settings are also loaded. 
 If you try to update the camera, create a configuration file after updating the 
firmware. If there is a firmware version...

Operating Instructions
162
6.1.8 Resetting the Camera to Factory Default
All camera settings are reset to factory default when the Execute button is clicked.
1.Click [Reset to Factory Default] on the Maintenance page.
2.Click [Execute].
 The indicator blinks orange, and then turns off for 10 seconds.
 All camera settings (user name, password, IP address, subnet mask etc.) 
are reset to factory default.
 If the camera is reset to factory default, the network connection mode 
changes to [Automatic...

Operating Instructions
163
6.2 Support page
6.2.1 The Help page
The Help page displays explanations for each of the following features.
Clicking [Help] on the Support page displays the following page.
6.2.2 Product Information
See the Panasonic Network Camera support website for product information.
Clicking [Product Information] on the Support page displays the URL, click it.
Note
 If the camera is not connected to the Internet, the website cannot be displayed.
6.2.3 Support Information
See the...

Operating Instructions
164
6.3 External I/O
If you connect external devices such as sensors to the External I/O, and image 
buffer/transfer by alarm signal is set, the camera image is transferred by alarm 
detection.
Explanation of the External I/O
Note
 The External I/O (Input/Output) are independent. Output terminal is controlled 
only by External Output Control page on page 152.Pin Features
G GND pin
1 External Sensor Input 1
 Use it by opening or GND short-circuit.
G GND pin
2 External Sensor Input...

Operating Instructions
165
Circuit Diagram Example
CAUTION
 The external I/O is not capable of connecting directly to devices that 
require large amounts of current. In some cases, a custom interface 
circuit (customer-provided) may have to be used. Serious damage to the 
camera may result if a device that exceeds its electrical capability is 
connected to the external I/O (see page 164).
 Low voltage/current circuits and high voltage/current circuits are used in 
the camera circuit. All wiring should...

Operating Instructions
166
7 Other Information
7.1 FACTORY DEFAULT RESET Button
There is a FACTORY DEFAULT RESET button on the bottom of the camera.
Pressing the FACTORY DEFAULT RESET button resets the camera to factory 
default. If you lose your user name and password, use this button to reset the 
camera.
 To reset the camera, press the FACTORY DEFAULT RESET button for 1 
second when the camera is on.
 The indicator blinks orange, and then turns off for 5 seconds.
Note
 The internal clock will not...

Operating Instructions
167
7.2 Default Setting List
Basic
Items Default Required Note
Network 
(IPv4)Connection Mode Automatic 
Setup- Automatic 
Setup/Static/
DHCP
Allow Access from the 
Internet (Automatic 
Setup only)No - -
Network Configuration 
from Setup Program 
(Static/DHCP only)Enable - -
Po r t  N o.  
(Static/DHCP only)80 - 20, 21, 25 and 
110 is not 
available
*2
IP address 
(Static only)192.168.0.
253When 
setting 
Static*1
Subnet Mask 
(Static only)255.255.
255.0When 
setting 
Static*1
Host...

Operating Instructions
168
Network 
(IPv6)Connection Mode Automatic 
Setup- Automatic 
Setup/Static
Allow Access from the 
Internet (Automatic 
Setup only)No - -
Por t No. 
(Static only)80 - 20, 21, 25 and 
110*
2 is not 
available.
IP address 
(Static only)[Blank] When 
setting 
Static
*1
Default Gateway (Static 
only)[Blank] When using 
Gateway*1
DNS Server 1
DNS Server 2[Blank] When using 
DNS*1
Max. Bandwidth Usage 
(Mbps)Unlimited - 0.1, 0.2, 0.3, 
0.5, 1 or 
Unlimited
Connection Type Auto...

Operating Instructions
169
Dynamic
DNSDynamicDNS Disable -Viewnetcam.com 
/User-specified 
DynamicDNS/
Disable
DynamicDNS Server 
URL[Blank]When using 
User-specified 
DynamicDNS1—255 
characters*8
Updating time 10 min At the time of 
starting/10, 
30(min), 1, 3, 
6, 12, 24(h)
User Name [Blank] 0—63 
characters
Password [Blank] 0—63 
characters
Date and 
TimeTime Setting AM/PM - AM/PM/24 H
Automatic Time 
AdjustmentNo check When using 
NTP-
NTP Server Address or 
Host Name[Blank] 1—255 
characters
*4...

Operating Instructions
170
Camera Camera Name Network
CameraRequired 1—15 
characters*6
White Balance Auto - Auto/Fixed 
Indoor/Fixed 
Fluorescent 
(White)/Fixed 
Fluorescent 
(Daylight)/
Fixed Outdoor/
Hold
AC Power Source 
Frequency60 Hz - 50 Hz, 60 Hz
Automatic Focus 
RangeMacro - Macro, Normal
Mounting Type On the table - On the table, 
On the ceiling
Pan Range (Minimum) -175 degrees - -175 — +175 
degrees, 
current
(Home Position)  0 degrees - -175 — +175 
degrees, 
current
(Maximum)
+175 degrees-...