Panasonic Multiplecer Board Wj Sxb151 Operating Instructions

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Multiplexer Board
Model No.WJ-SXB151
WARNING:
• All work related to the installation of this product should be made by qualified service personnel  or system installers.
■General ................................................................................................................. 2
■Precautions...

■Procedure Flow
*The version is displayed in WJ-SX150 SETUP
MENU.
(Refer to the matrix switcher’s operating instruc-
tions.)
** The version printed on the CD-ROM label.
*** Refer to the matrix switcher’s operating instructions.
Start
Firmware version check*
CD-ROM version is newer
 than SETUP MENU.SETUP MENU version is
 newer or equal to CD-ROM.
SX150
Firmware Update
Setup Procedures***
Confirmation of WJ-SX150 operation*** Program Writer
InstallationConnections*** WJ-SXB151 Installation CD-ROM version...

-3-
HARDWARE PREPARATION
■Installation of Multiplexer
Board WJ-SXB151
●The Features of Multiplexer Board 
WJ-SXB151
Multiplexer Board WJ-SXB151 is an optional accessory
specified for Matrix Switcher WJ-SX150.
The board installation will add the following functions to
the matrix switcher.
•A monitor can display up to 16 camera images in
multiscreen segments. (Multiscreen output)
A desired image can be displayed as a still picture.
(Still output)
•The matrix switcher can detect a moving object with
the...

-4- eFasten the cooling fan with the screws removed
in step q.
4. Install the Multiplexer board.
qRemove the flatcable connected to the CN903
connector (the main circuit board) of the matrix
switcher.
wConnect the supplied flatcables and wirecables
to the matrix switchers connector.
• Main circuit board
Connector # Cable type
CN904 20-pin flatcable
CN905 18-pin flatcable
CN11 7-pin wirecable
CN12 50-pin flatcable
• Sub circuit board
Connector # Cable type
CN77 6-pin wirecable
CN81 8-pin flat cable...

-5-
qPull up
wConnect
ePush downqPull up
qPull outwConnectePush in
qPull upwConnectePush down
qPull outwConnectePush in wConnect
ePush down
Note: Connect the cables to the connectors straightforward. Inclined insertion
   may cause a short circuit, which will result in a malfunction or trouble.
•Matrix switcher
  CN12 (50-pin) •Matrix switcher
  CN904 (20-pin)
  CN905 (18-pin)•Multiplexer board : CN1002 (20-pin), CN1001 (18-pin)
•Multiplexer board : CN1003 (8-pin)
•Matrix switcher : CN81 (8-pin)...

-6-
FIRMWARE UPDATE
Note:Confirm the firmware version. (Refer to the matrix
switcher’s operating instructions.) 
■Installation of SX150 Program
Writer
Note:Refer to the matrix switcher’s operating instruc-
tions for the platform necessary for installation.
1. Connect the matrix switchers serial port to that of
the PC with the 9-pin D-sub cable. (Refer to the
matrix switcher’s operating instructions.)
2. Insert the supplied CD-ROM into the PC.
3. Open the CD-ROM drive window.
The file is located in the...

-7- 6. When you power on the matrix switcher and the sys-
tem becomes ready for update, the following mes-
sage will appear on the PC screen.
“✽FIRMWARE UPLOAD START! WAIT…”
7. Wait until the following message appears.
“✽✽SDRAM INITIALIZE COMPLETED.START LOAD-
ING…”
8. Insert the supplied CD-ROM into the PC.
9. Click on the “Browse…” button to select a .mot file.
The file is located in the following.
E: WJ-SXB151P/PWriter/sx150_v✽✽✽✽✽.mot (E is
the CD-ROM drive and ✽is the software version. For
example,...

-8-
■Error List
The following error messages are displayed through
SX150 Program Writer.
●File Error
This error message is displayed during the following
occasions.
•You have selected a wrong file (whose file extension
is not “. mot”) in Step 9 of p.7.
•The “.mot” file is broken.
To solve this problem, select the correct file. (Refer to p.
7.)
●Not Ready
This error message is displayed when the matrix
switcher’s mode is not “SX150 SOFTWARE UPLOAD”.
To solve this problem, do the following.
1. Power off...

-9-
TROUBLESHOOTING
Prior to having the unit repaired, check the following items.
Camera image is displayed even
after the playback is started.
Time-lapse recording is unavail-
able. The matrix switcher does not
power up.
Camera image is not displayed
even after selecting the camera.Problem Check item
The power cord may be disconnected either from the matrix switcher’s power socket
or the AC outlet.
The camera’s power cord connection may be wrong.
The lens cover may not have been removed from the...

-10-
■Specifications
Required Power: DC +3.3 V/+5 V/+12 V (Supplied from WJ-SX150)
Power Consumption: 150 mA at 3.3 V, 1 A at 5 V, 850 mA at 12 V
Operating Temperature: From –10°C (14°F) to +50°C (122°F)
Dimensions: 312 mm (W) x 189 mm (H) x 23 mm (D)
12.3” (W) x 7.4” (D) x 0.9” (H)
Weight: 440 g(0.97 lbs.)
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
■Accessories
Flatcable ..........................................................................3...