Panasonic Multi Media Projection Display Pt 40lc12 Operating Instruction

							31
Basic Operation
ASPECT Controls
Notes:
• The screen size changes if ID-1 is detected. (P. 55)Mode
NORMAL will display a 4:3 picture at its standard
4:3 size. Picture
ZOOM
FULL NORMAL
JUSTExplanation
ZOOM mode magnifies the central section of the
picture. JUST mode will display a 4:3 picture at maxi-
mum size but with aspect correction applied to
the center of the screen so that elongation is
only apparent at the left and right edges of the
screen. The size of the picture will depend on the
original signal.
FULL will display the picture at its maximum
size but with sight elongation.
TRUE
NORMAL
3 4
ZOOM
16
9
FULL
16
9
JUST
9 16
TRUE
3
4
You can reduce the image and adjust it to the
original image quality. (Except XGA) 
						

							32For assistance, please call : 1-888-VIEW PTV(843-9788)
Searching for the desired channel (Channel search)
When the SEARCH/REC button is pressed during
single screen.
When a channel button is pressed during
channel search.
• Number keys:
Example: When 6 is pressed, channel 6 is displayed in single
screen.
• Channel up and down buttons:
When 
 or  button is pressed, the next channel up or down is
displayed in single screen.
Sound from the left screen is
output from the speakers on the
projection display set.
Channel search displays each channel, in order, as a paused image. Channels are displayed
from the left top to the right bottom in order. When it reaches the right bottom, the next
channel is displayed at the left top, overwriting the previously displayed channel.
Notes:
• To end channel search, press SEARCH/REC.
• While using the PIP feature, Channel search is not available.
CH06
Ex. Select channel 6
CH03
CH030205
06
0810 07
RGB
0205
0607
10 08
?%@
Or 
						

							33
Basic Operation
Playing peripheral equipment
VCR
DVD player
This equipment can also be
connected to the rear terminals.
See Connections for details.
Turning the power on and switching input modes
Turn the projection
display on.
1
2
The input mode
changes each time
this button is pressed.
* No input mode is
displayed for terminals
with no equipment
connected.
3Operate the connected equipment.
Confirming connections
A video camera uses the Input 3 terminal on the front of the projection display.
Video camera
To S-video output
or video output
To audio output
LINE 1:
Signal of source connected to INPUT 1 is displayed.
LINE 2:
Signal of source connected to INPUT 2 is displayed.
LINE 3:
Signal of source connected to INPUT 3 is displayed.
COMPONENT 1:
Signal of source connected to COMPONENT VIDEO INPUT 1 is displayed.
COMPONENT 2:
Signal of source connected to COMPONENT VIDEO INPUT 2 is displayed.
RGB:
Signal of source connected to PC IN is displayed.
TV
LINE 1
LINE 2
LINE 3
RGB
COMPONENT 2
COMPONENT 1
*
*
* *
* Example: Connect Input 3 
						

							34For assistance, please call : 1-888-VIEW PTV(843-9788)
Press this button to mute the sound. Press again to
reactivate sound. Sound is also reactivated when power
is turned off or volume level is changed.
Projection can be switched between a frozen (still)
picture and a moving picture each time the FREEZE
button on the remote control unit is pressed. Press
FREEZE button again to resume motion.
Mute / Freeze / SAP
Sound mute
Useful when answering the phone or receiving
unexpected visitors
Freezing pictures
E Z E E R F
E T U M
Note:
The audio output from AV OUT is not muted.
Note:
The video output from AV OUT is not frozen. 
						

							35
Basic Operation
The following are possible broadcast types with their accompanying on-screen displays. The signal being
received is indicated with a “ 
 ” mark while the selected audio mode is indicated with an arrow. To change the
audio mode for these broadcasts, follow the “Select Audio Mode for TV Viewing” section (below.)
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main language) and Secondary
Audio Program (sub language) broadcasts are both being received
simultaneously.
Select the STEREO or SAP audio mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast. Select STEREO
audio mode.
• If stereo broadcast is weak and the display flickers, select MONO
audio mode for possibly better results.
SAP broadcast
Secondary Audio Program (sub language.)
Select SAP audio mode for the sub language.
MONO broadcast
Normal monaural sound broadcast.
Receivable Broadcast Types
2 1 H C
O E R E T S
P A S
O N O M
2 1 H C
P A S
O N O MO E R E T S
2 1 H C
P A S
O N O MO E R E T S
2 1 H C
P A S
O N O MO E R E T S
Press SAP button to select the desired audio mode as described below.
(Arrow shows selection.)
• Each press of SAP button will change the audio mode as shown below.
• “SAP” is selected with first press of SAP button.
Select Audio Mode for TV Viewing
Mute / Freeze / SAP
< Example >
Press
SAP2 1 H C
O E R E T S
P A S
O N O M
2 1 H C
P A S
O N O MO E R E T S
2 1 H C
P A S
O N O MO E R E T SPress
SAP
Press
SAP 
						

							36For assistance, please call : 1-888-VIEW PTV(843-9788)
Notes:
• Sound from the Left screen is output from
the speakers on the projection display set.
• When the screen is split, signals of the Left
screen are output from the rear monitor
output terminal.
• The left and right screens are processed by
individual circuits and, therefore, may
slightly vary in image quality.
• Split screen returns to single screen when
the projection display is turned off.
• With the Left screen, as with a single
screen, you can change the input, change
channels, and adjust the volume.
• The right and left screens cannot display
the same picture at the same time.
• A split screen which includes an RGB signal
from a PC is fixed as SPLIT SCREEN
NORMAL (PC input).
Split screen
Splitting the screen
Press to split.
(The previously selected screen appears on the left.)
• Returning to one screen.
Press to return.
Selecting the screen mode for split screen.
Press to
select
modes.
CH03CH05
CH03CH05
CH03CH05
SPLIT SCREEN NORMAL
SPLIT SCREEN NORMAL
(PC input)
RGB
CH05
Left screen
(Main picture)Right screen
(Sub picture)
SPLIT SCREEN FULL 
						

							37
Basic Operation
Swapping left and right screens
Example:
During SPLIT SCREEN NORMAL.
Split screen
CH05CH03
CH03CH05
Changing the channel of the right screen
1
CH03CH05
CH03CH06
Press to swap.
Example:
During SPLIT SCREEN NORMAL.
Note:
When outside input is finished, the lowest regis-
tered channel number is displayed. For faster
selection, press the SWAP button to change the
screen to the left. Then, press the TV/VIDEO button
to directly change the input. Finally, press SWAP
button again to change the screen back to the right.
125 or 69
CABLE
CH01
CH125
LINE 1
LINE 2
LINE 3
RGB
COMPONENT 2
COMPONENT 1
TV
Press to select the desired
channel.
PIP 
,  buttons can also be used to select an
outside input for the right side of the screen.
* No input mode
is displayed for
terminals with
no equipment
connected.**
*
*
*
RGB
CH05
RGB
CH05
Example:
During SPLIT SCREEN NORMAL
(PC input)
Note:
Picture quality may change according to the
combination of signals input to the left and right
screens. 
						

							38For assistance, please call : 1-888-VIEW PTV(843-9788)
CH03
PIP CH05
Picture in Picture (PIP) Screen
You can view two pictures simultaneously using two tuners and picture in picture (PIP) display function.
Display PIP screen
Press to split
(The previously selected screen appears on the Main.)
• Returning to one screen.
Press to return.
Main screen
(Main picture)
PIP screen
(Sub picture)
Notes:
• Sound from the Main screen is output from the speakers on the
projection display set.
• In PIP mode, the Main screen signal is output from the rear
monitor output terminal.
• Because Main and PIP screens are processed by individual
circuits, image quality may vary slightly.
• PIP mode returns to single screen when the projection display is
turned off.
• The Main and PIP screens cannot display the same picture at
the same time.
• An RGB signal cannot be displayed on a PIP screen or a Main
screen.
• A component signal cannot be displayed on a PIP screen. Thus,
when a component signal is displayed on the Main screen, the
SWAP button becomes invalid.
• With the Main screen, as with a single screen, you can change
the input, change channels, and adjust the volume. 
						

							39
Basic Operation
Picture in Picture (PIP) Screen
Swapping Main and PIP screens
Press to swap.
Changing the channel of the PIP screen
Move PIP screen
You can move the PIP screen to four positions.
Press repeatedly
to select PIP
position.
CH03
PIP CH05
CH03
PIP CH06
CH03
PIP CH05
CH05
PIP CH03
Press to select the desired channel.
Example:
During Main screen NORMAL.Example:
During Main screen NORMAL.
Selecting the screen size for PIP screen
You can choose PIP screen size of 3 magnifications.
Press repeatedly
to select PIP
screen size.
Note:
PIP ,  buttons can also be used to select an outside input for
the PIP screen.
Initial size
CH03
2 1
CH0312
3
Initial position
Note:
The last size chosen is saved and will not be erased
even if the power is turned off.Note:
The last position chosen is saved and will not be
erased even if the power is turned off. 
						

							40For assistance, please call : 1-888-VIEW PTV(843-9788)
Adjusting screen position and size
4
Press the ACTION button to display the MENU screen and select
ADJUST.
Press to select
POSITION/SIZE.
Press to display
POSITION/SIZE.
Press to adjust
POSITION/SIZE.
2
3
PAGE SELECT
ENDRECALL
P U T E S
H S I L G N E : E G A U G N A L
L E N N A H C
K C O L
N O I T P A C
O E D I V
PAGE SELECT
ENDRECALL
T S U J D APU T E S
E R U T C I P
O I D U A
E Z I S / N O I T I S O P
N O I T A M R O F N I
Press to select the screen mode.1
SELECT ADJUST
EXITRECALL
N O I T I S O P H
N O I T I S O P V
K N I R H S : H T D I W H
L A M R O N
N O I T I S O P
SELECT
EXITRECALL
N O I T I S O P H
N O I T I S O P V
N E D I W : H T D I W H
L A M R O N
ADJUST
N O I T I S O P
SELECT ADJUST
EXITRECALL
N O I T I S O P H
N O I T I S O P V
E Z I S H
E S A H P
L A M R O N
N O I T I S O P
SELECT ADJUST
EXITRECALL
N O I T I S O P H
N O I T I S O P V
E Z I S V
L A M R O N
N O I T I S O P
PC input ZOOM mode NORMAL modeJUST mode
Press to exit menu.
Press to
select the
menu to set
each item.
NORMAL is displayed at default.
SELECT
EXITRECALL
N O I T I S O P H
N O I T I S O P V
L A M R O N
ADJUST
N O I T I S O P
FULL mode