Panasonic Multi Media Projection Display Pt 40lc12 Operating Instruction

							21
Basic Operation
Power ON / OFF
Always be sure to follow the procedure given below to turn the projection display power ON and OFF.
• The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off.
At the same time, the POWER indicator will blink Red.
Do not disconnect the power cord from the power outlet and do not open any circuit breakers while the
cooling fan is still operating.
Do not disconnect the power cord from the power outlet while the power indicator blinks Red.
Press the POWER button on the projection display or the
remote control to turn the power on.
The Power Indicator will become Green and blink for
approximately 10 seconds, and then turn solid Green.
The Power Indicator
LED ACTION
Notes:
• If the POWER button is accidentally turned off during use, after power is turned back on, it may take a short period
before the lamp automatically comes on.
• After the unit is turned on, maximum picture brightness will be achieved in 5-10 minutes. This is normal.
Power – OFF (Standby mode)
Power – OFF (Now cooling)
Power – ON
Power – ON (Preparing to light lamp) Red
Red blink
Green
Green blink
Press the POWER button on the projection display or the
remote control to turn the power off. Confirming message
will appear.
Note:
When the AC Cord is unplugged, the internal cooling fan stops operating. In this case, the lamp will be insufficiently
cooled and will take a while to turn ON again.
Power ON
Power OFF
The Power Indicator will become Red and blink for
approximately 1 minute, and then turn solid Red.
Press the POWER button again.
Turning the Power ON and OFF
POWER OFF
YES
NO
POWER button/
POWER indicator
If the POWER button is accidentally pressed, select NO
with the 
 ,   buttons, then press the ACTION button. 
						

							22For assistance, please call : 1-888-VIEW PTV(843-9788)
Flow Chart of Main menu
2
PAGE SELECT
ENDRECALL
P U T E S
H S I L G N E : E G A U G N A L
L E N N A H C
K C O L
N O I T P A C
O E D I V
PAGE SELECT
ENDRECALL
T S U J D APU T E S
E R U T C I P
O I D U A
E Z I S / N O I T I S O P
N O I T A M R O F N I
PAGE SELECT
ENDRECALL
T S U J D APU T E S
E R U T C I P
O I D U A
E Z I S / N O I T I S O P
N O I T A M R O F N I
PAGE SELECT
ENDRECALL
P U T E S
H S I L G N E : E G A U G N A L
L E N N A H C
K C O L
N O I T P A C
O E D I V
Use the  ,  buttons to
select an item.Select MENU desired by
pushing Left “
 ” button
or Right “ 
” button.
Use the ACTION button
to set or go to next menu
screen.
Pressing the ACTION
button displays the
MENU screen.
Note:
Depending on the signal
being input, some items
may or may not be
adjustable and some
functions may or may not
be available.
1 
						

							23
Basic Operation
Flow Chart of Main menu
Returning to the previous screen
If you press the RECALL button while a
menu screen is being displayed, the display
will return to the previous screen. Adjust items
Set an item
EXITRECALL
i 0 8 4L A N G I S T U P N I
INFORMATION
screen
P.   5 7
SELECT
EXITRECALL
N O I T I S O P HN O I T I S O P
N O I T I S O P V
W O R R A N : H T D I W H
L A M R O N
ADJUST
TO POSITION/SIZE
ADJUST menu
PP. 40, 41
SELECT
EXITRECALL
O I D U A
L A M R O N : U N E M O I D U A
T S U J D A O I D U A
N O : R E K A E P S
F F O : D N U O R R U S
TO AUDIO
ADJUST menu
PP. 42, 43
SELECT
EXITRECALL
L A M R O N : U N E M E R U T C I P
T S U J D A E R U T C I P
L A M R O N : E D O M G N I W E I V
E R U T C I P
TO PICTURE
ADJUST menu
PP. 44, 45
PAGE SELECT
ENDRECALL
T S U J D APU T E S
E R U T C I P
O I D U A
E Z I S / N O I T I S O P
N O I T A M R O F N I
PAGE SELECT
ENDRECALL
P U T E S
H S I L G N E : E G A U G N A L
L E N N A H C
K C O L
N O I T P A C
O E D I V
TO LANGUAGE
selection screen
P.   5 7TO CHANNEL
menu
PP. 24-27, 52, 53
SELECT
EXITRECALL
L E N N A H C P U T E S
E L B A C : A N N E T N A
T E S O T U A
T E S L A U N A M
N O I T P A C L E N N A H C
F F O : Y A L P S I D L A N G I S K A E W
PP. 46-49 TO LOCK
selection screen
EXITRECALL
K C O L
E D O C T I G I D - 4 R E T N E
9 - 0 : R E T N E
- - - -
TO CAPTION
menu
PP. 50, 51
SELECT
EXITRECALL
N O I T P A C
F F O : E D O M N O I T P A C
1 C P A C : E T U M N O C C
SELECT
EXITRECALL
O E D I V
F F O : R N O E D I V
A G V : B G RF F O : 1 - D I
V T D S : X I R T A M R O L O C P 0 8 4
TO VIDEO
menu
P. 54-56
Select an item 
						

							24For assistance, please call : 1-888-VIEW PTV(843-9788)
Tuning channels
Automatically searches and adds receivable channels to memory.
Press the ACTION button to display the MENU screen and select SET
UP.
Press to select
CHANNEL.
Press to display
the CHANNEL.
Press to select
TV or CABLE.Press to select
ANTENNA.
Press to select
AUTO SET.
Press to run
AUTO SET.
Note:
TV or Cable Tuning mode must be set according to your connections.
1
2
3
PAGE SELECT
ENDRECALL
T S U J D APU T E S
E R U T C I P
O I D U A
E Z I S / N O I T I S O P
N O I T A M R O F N I
PAGE SELECT
ENDRECALL
P U T E S
H S I L G N E : E G A U G N A L
L E N N A H C
K C O L
N O I T P A C
O E D I V
SELECT
EXITRECALL
L E N N A H C P U T E S
E L B A C : A N N E T N A
T E S O T U A
T E S L A U N A M
N O I T P A C L E N N A H C
F F O : Y A L P S I D L A N G I S K A E W
SELECT
EXITRECALL
L E N N A H C P U T E S
E L B A C : A N N E T N A
T E S O T U A
T E S L A U N A M
N O I T P A C L E N N A H C
F F O : Y A L P S I D L A N G I S K A E W
G N I D E E C O R P T E S O T U A H C
Channels will automatically advance until all channels have been
scanned. Channel numbers with a video signal present will be
stored in the channel scan memory.
Automatic channel setting
Continued on the next page. Note:
To cancel AUTO SET in progress,
press the SWAP button. 
						

							25
Basic Operation
Notes:
• After AUTO SET is finished, the lowest channel number added will be received.
• Some channels with very weak signals may be locked into memory. It desired, these channels can be deleted
manually using the MANUAL SET feature.
Tuning channels
4
 Case 1
 Case 2When setup is complete, the lowest channel picture
appears.
If setup is incomplete, the screen at right appears. Check
connection of Antenna/Cable to the RF in Terminal, then try
Automatic Channel Setting again.
Press to exit menu.
5
N I A G A Y E K N O I T C A S S E R PA N N E T N A K C E H C E S A E L P
N E H T N O I T C E N N O C E L B A CD N U O F H C O N 
						

							26For assistance, please call : 1-888-VIEW PTV(843-9788)
Tuning channels
Use this setting when changing setting of receiving channels or changing the channel
display.
3
Press to select
MANUAL
SET.
Press to display
the MANUAL
SET screen.
Press the ACTION button to display the MENU screen and select SET
UP.
Press to select
CHANNEL.
Press to display
the CHANNEL.
Press to select
TV or CABLE.Press to select
ANTENNA.
1
2
SELECT
EXITRECALL
L E N N A H C P U T E S
E L B A C : A N N E T N A
T E S O T U A
T E S L A U N A M
N O I T P A C L E N N A H C
F F O : Y A L P S I D L A N G I S K A E W
SELECT
EXITRECALL
L E N N A H C P U T E S
E L B A C : A N N E T N A
T E S O T U A
T E S L A U N A M
N O I T P A C L E N N A H C
F F O : Y A L P S I D L A N G I S K A E W
Manual channel setting
Continued on the next page.
PAGE SELECT
ENDRECALL
T S U J D APU T E S
E R U T C I P
O I D U A
E Z I S / N O I T I S O P
N O I T A M R O F N I
PAGE SELECT
ENDRECALL
P U T E S
H S I L G N E : E G A U G N A L
L E N N A H C
K C O L
N O I T P A C
O E D I V 
						

							27
Basic Operation
4
ADDEXITRECALL
T E S L A U N A M
1 0 : L E N N A H C R E T N E
L E N N A H C A E S O O H C
N W O D / P U H C G N I S U
Press to select channel.
Repeat steps 4 to continue adding or deleting channels.Press to add channels to memory.
Press to select channel.
Press to delete channels from memory.
Press to exit menu.
Note:
Some channels with very weak signals may be locked into memory. It desired, these channels can be deleted manually
using the MANUAL SET feature.
5
6
Tuning channels
DELETE
EXITRECALL
T E S L A U N A M
L E N N A H C A E S O O H C
1 0 : L E N N A H C R E T N E
N W O D / P U H C G N I S U
To add channel
To delete channel 
						

							28For assistance, please call : 1-888-VIEW PTV(843-9788)
Projection display operation
Operation can be done from the projection
display.
Press to
select the
desired
volume
level. Press to select
the desired
channel. (or use
number keys ) Press to turn the projection display on. Press to operate the projection
display with the remote control.
1
2
3
4
Notes:
• The channel number and volume level are stored even after the projection display is turned off.
• Power consumption can be reduced if the volume level is lowered.
Or
Remote Control Sensor POWER button/
POWER indicator
Volume up(+) / down(–) buttons Channel up / down buttons
CH03
26
125 or 69
CABLE
CH01
CH02
CH125
TV
Note:
Refer to “Using
the number keys”
on the next page. 
						

							29
Basic Operation
Projection display operation
2 1 H C
C B A L A M R O N
O E R E T S
P A S
O N O MAspect types
(P. 30)
Receivable
broadcast types
(P. 35)Channel
Channel caption
(P. 52)
TV status display
Using the number keys
Example 1: To select channel 125, first press the 1 key, then 2, then 5. When selecting CABLE channels 100 to 125 with the number keys, first press the 1 key,
and then enter the remaining two digits.Press the RECALL button, except when the MENU screen is displayed, to display current
TV status information.
Example 2: To select channel 12, press the 1 key, then 2. Channel 12 appears momentarily.
Example 3: To select channel 8, press the 8 key. Channel 8 appears momentarily.
FREEZEInvalid operation notice feature
If an invalid operation is attempted, the mark shown right is
displayed.
125 or 69CABLE
CH01
CH125
LINE 1
LINE 2
LINE 3
RGB
COMPONENT 2
COMPONENT 1
TV
%!5
))
!!	
O & &!
$&	OO
O
O
O
Using projection display Channel up/down buttons to select input mode
Auto shut off
To extend lamp life, if there is no signal to the set’s tuner for 5 minutes, the lamp will shut off automatically. 
						

							30For assistance, please call : 1-888-VIEW PTV(843-9788)
ASPECT Controls
The color monitor will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema
format picture.
The aspect mode changes each time the ASPECT
button is pressed.
Notes:
• When a 480p signal is being received, the mode switches between
NORMAL, ZOOM, and FULL only.
• When a 1080i and 720p signal is being received, the mode is set to
FULL, and aspect switching is not possible.
• During PC input, the mode switches between NORMAL, TRUE and
FULL only.
NORMAL                  JUST
FULL                    ZOOM
FULL NORMAL
FULL
FULL NORMAL TRUE
Notes:
• However, if the mode selected does not match the aspect ratio of the input signal, the original picture quality may be
affected.
• If using this Projection display in places, such as cafes or hotels, with the aim of displaying programs for a
commercial purpose or for public presentation, please note that by using the aspect ratio (16:9) selection function to
change the aspect ratio, you may be infringing on the rights of the original copyright owner of that program under
copyright protection laws.
• If a normal (4:3) picture is projected in wide screen, distortion may occur around the edges so that part of the picture
may no longer be visible. We recommend viewing in 4:3 mode so you can enjoy the picture as it was intended to be
seen.• When XGA and Mac 19 signal is input, the aspect will be NORMAL
and FULL only.