Panasonic Monitor Bt Lh80w Owners Manual

21
SYSTEM CONFIGThe underlined values are factory preset setting values.
Sub menu Settings Explanation
CONT. /BACK.BACKLIGHT
CONTRASTUsed to select the function to be assigned to CONT/B.LIGHT (a knob 
on the front panel).
  Used to adjust BACKLIGHT.
   Used to adjust CONTRAST.
BACKLIGHT0 - 60 Used to adjust the LCD backlight level.

CONT./BACK displays “-” while BACKLIGHT settings are performed.
PEAKING/PHASEPEAKING
PHASEUsed to select the function to be assigned to PEAK/PHASE (a knob 
on the front...

22
VF CONFIGThe underlined values are factory preset setting values.
Sub menu Settings Explanation
VF CONTROLVF-CH
ALL-CHUsed to select the input line for the VF function of the monitor.
(VF function: tally lamp lit, zebra displayed, 
 displayed)
   Only enabled when the VF line is selected.
  Enabled with all input lines.
CROSS HATCHHIGH
LOW
OFFUsed to set whether to display a cross hatch and select its density 
level.
 70/256 (displays with a dense cross hatch)
  20/256 (displays with a light cross...

23
FUNCTIONThe underlined values are factory preset setting values.
Sub menu Settings Explanation
FUNCTION1 - 3BLUE ONLY
SD ASPECT∗
1∗2
WFM
MARKER∗1∗3
PIXEL TO PIXEL∗4
PIXEL POS.+∗5
PIXEL POS.–∗5
FOCUS-IN-RED
∗4∗7 
ZEBRA
REAR TALLY∗6
CROSS HATCH
MONO∗1
UNDEF
(Factory preset
setting→
FUNCTION1:
WFM
FUNCTION2:
PIXEL TO PIXEL
FUNCTION3:
FOCUS-IN-RED)Used to select the functions to be assigned to individual buttons 
[FUNCTION1] to [FUNCTION3] (front-panel buttons).

Used to cut the red and green signals. You...

24
Main Menu (continued)
  Restrictions on various FUNCTION settings
    Under the following conditions, various settings are disabled.
Setting Disabling condition
SD ASPECTDoes not operate while GPI items are being set. Does not operate during PIXEL TO PIXEL 
operation.
Does not operate during HD display.
If operated during the conditions described above, “INVALID FUNCTION” is displayed.
WFMDoes not operate during PIXEL TO PIXEL or FOCUS-IN-RED mode.
If operated during the conditions described above,...

25
Main Menu (continued)
 About WFM
    You can display the wave form monitor using the “WFM” function.
   The display changes each time you press one of the buttons, [FUNCTION1] to [FUNCTION3] (→ page 23), 
assigned with the [WFM] function (To use the “WFM” function, you must assign it to one of the [FUNCTION1] to 
[FUNCTION3] buttons).
Press the FUNCTION button assigned 
with the WFM function once.
Normal window WFM displayPress the 
same button 
again.
WFM (Wave Form Monitor)
The window is displayed...

26
Main Menu (continued)
Display position sequence during an HD signal 1080i input
  PIXEL POS.+: 1)→2)→3)→4)→5)→6)→7)→8)→9)→1) · · · · ·
  PIXEL POS.–: 1)→9)→8)→7)→6)→5)→4)→3)→2)→1) · · · · ·
1) CENTER 2) LEFT TOP 3) MID TOP
4) RIGHT TOP 5) RIGHT MID 6) RIGHT BOTTOM
7) MID BOTTOM 8) LEFT BOTTOM 9) LEFT MID
Display position sequence during an HD signal 720P input  
  PIXEL POS.+: 1)→2)→3)→4)→5)→1) · · · · ·
  PIXEL POS.–: 1)→5)→4)→3)→2)→1) · · · · ·
1) CENTER 2) LEFT TOP 3) RIGHT TOP
4) RIGHT BOTTOM 5)...

27
Main Menu (continued)
Push once the FUNCTION button to 
which the FOCUS-IN-RED function is 
assigned.
Normal screen FOCUS-IN-RED displayPush the 
same button 
once more
Displays in red the section of the 
image that is being focused
The aspect of 16:9 in the screen example.
 About FOCUS-IN-RED
   When the FOCUS-IN-RED function is used, the section that is being focused is displayed in an easy-to-understand 
red, making camera focus adjustments easy.
   Each time the button from [FUNCTION1] to...

28
GPIThe “GPI CONTROL” item is used to set enable/disable of all GPI functions, and assigns functions to each of the 
GPI terminal pins (→ page 31).
The underlined values are factory preset setting values.
Sub menu Settings Explanation
GPI CONTROLDISABLE
ENABLEGPI functions enable/disable settings
 Deactivate
 Activate
GPI1 - GPI8UNDEF
MARKER1 ON/OFF
MARKER2 ON/OFF
MARKER BACK HALF
MARKER BACK BLACK
CENTER MARKER
INPUT SEL. YP
BPRINPUT SEL. VF
INPUT SEL. VIDEO
INPUT SEL. SDI
SD ASPECT
RED TALLY
GREEN...

29
INPUT SELECTThe underlined values are factory preset setting values.
Sub menu Settings Explanation
YP
BPRON
OFFUsed to set the YPBPR line to the INPUT SELECT button.∗1
COMPONENT 
LEVELSMPTE
B75
B00Used to select the input level for the YPBPR (component) signal.
  When the signal level specified in SMPTE is Chroma 100 
IRE, P
B, PR=0.7Vp-p
     Select this when connecting a betacam or similar devices 
with a 7.5 IRE setup level.
     Select this when connecting a betacam or similar devices 
with a 0...

[MAIN MENU]
MARKER
30
CONTROLThe underlined values are factory preset setting values.
Sub menu Settings Explanation
CONTROLLOCAL
REMOTEUsed to select the operation. (Combined control lock)
   Front operation enabled
 Remote operation enabled
          (The front controls become locked)∗
1
LOCAL
ENABLEDISABLE
INPUTWhen “REMOTE” is selected in “CONTROL”, this selects whether 
front controls are enabled/disabled.
 All front operations are disabled.
    Operations other than those with the [INPUT SELECT]...