Panasonic Monitor Bt Lh1700w Owners Manual

21
The underlined values are factory preset setting values. 
*1
“AUTO” is set when the monitor is shipped from the factory, but if there are concerns about noise etc. from outside the 
input signal, we recommend assigning specific format. 
gCOMP. 
The following menus are switched by selecting “RGB-COMP.” in “YP
BPR/RGB” in the “INPUT SELECT” menu. 
The underlined values are factory preset setting values.
 
*1 “EXECUTING” is displayed while “AUTOSETUP” is being executed, and “COMPLETE” is displayed when...

22
g “PHASE” and “CLOCK” factory preset setting values
Adjusting the speaker output. This can only be set when the monitor is equipped with an embedded audio unit BT-
YAE1700G (optional). If the monitor is not equipped with an embedded audio unit, the output will be in analog. 
The underlined values are factory preset setting values. 
The underlined values are factory preset setting values. 
*1 The menu can be displayed when the lock is engaged.  
The only menu setting that can be changed when the lock...

23
REMOTE operation is possible on this monitor using the GPI/RS-232C terminal. 
Each of the items in the GPI screen are compatible with the following terminals. 
You can assign functions to each terminal in the menu GPI screen (J page 20). 
The functions assigned to each terminal operate when the GND (5 Pin) is connected (ON) or open (OFF). 
gOperating conditions
Level operation: operates when GND is connected. 
Edge operation: operates when GND changes from 
open to connected.
* If you have assigned a...

24
gAssignment of item priority levels
 When both “MARKER1” and “MARKER2” are ON at the same time, “MARKER1” has priority. 
 When both “MARKER BACKHALF” and “MARKER BACKBLACK” are ON at the same time, “MARKER 
BACKBLACK” has priority. 
 When more than 2 of “INPUT SEL. VIDEO”, “INPUT SEL. Y/C”, “INPUT SEL. SDI1”, “INPUT SEL. SDI2”, “INPUT 
SEL. YP
BPR/RGB” are ON at the same time, the one that was switched ON last has priority. 
Refer to the following diagram and lower right table for the RS-232C...

25
gSetting command
No Command Explanation Data Response
1IIS Input switch 0: SDI1  1: SDI2  2: VIDEO
3: YP
BPR/RGB 4: Y/CIIS
2VPS Image quality 
adjustment CON00-60 : Contrast settings
BRI00-60 : Brightness settings
CRO00-60 : Chroma settings
PHA00-60 : Phase settingsVPS
3
OBO Blue only 0: OFF  1: ON OBO
4OHV HV Delay 0: OFF  1: H DELAY  2: V DELAY  
3: HV DELAYOHV
5
DSD Status display 0: CONTINUE  1: 3SEC OFF  2: OFF DSD
6IMS Analog mode ANA0: YP
BPR ANA1: RGB-VIDEO  
ANA2: RGB-COMP.IMS
7
IRF RGB Sync...

26
gQuery command
No Command Explanation Data Response
1QIS Input selection 0: SDI1 1: SDI2 2: YP
BPR 
3: RGB-VIDEO 4: VIDEO 5: Y/C 
6: RGB-COMP.
2QPC Image quality 
adjustment CON : Contrast setting 
value00-60
BRI : Brightness setting 
value00-60
CRO : Chroma setting value 00-60
PHA : Phase setting value 00-60
3
QBO
Blue only0: OFF  1: ON
4QMK Marker MAK : Area marker 00: OFF 01: 80% 02: 88%  
03: 93% 04: 95% 05: 14:9  
06: 13:9 07: 4:3 08: 90% 
09: CNSCO 10: VISTA
BAK : Background 0: NORMAL  1: HALF...

27
If you use rack-mounting adaptors BT-MA1710G (optional) with this monitor, you can incorporate a 19-inch 
standard rack (the height is 7U size). Please see the instructions below for attachment. 
1. Remove the screws on the back and base of the 
monitor (3 places), and remove the stand. 2. Using the screws provided, attach the rack-
mounting adaptors to both sides of the monitor. 
Error/Warning Displays
If for any reason an error occurs in this monitor, the LEDs above the picture adjusting knob flash...

28
Maintenance inspections are necessary for the user to use this equipment safely. It is important to keep monitor 
functions in good condition at all times through periodical and appropriate maintenance. In order to use this monitor 
for a long time, and to make full use of all of its functions, be sure to carry out the following maintenance 
inspections. 
1. Necessity of periodical maintenance services
A backlight is used in the liquid crystal panel. This 
part (consumable) deteriorates as time...

29
gList of compatible signal formats
*1 When 1035/59.94I signal is input, displayed as 1080/59.94I. Other various marker displays will use the 1080/
59.94I marker. 
*2 When 1035/60I signal is input, displayed as 1080/60I. Other various marker displays will use the 1080/60I 
marker. 
Weight and dimensions when shown are approximately.
Specifications are subject to change without notice.
Input signal 
formatsVIDEO Y/C SDI1 SDI2 YPBPRRGB-VIDEO RGB-COMP.
NTSC
PA L
480/59.94I
480/59.94P
576/50I
576/50P...

P
© 2005 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330...