Panasonic Monitor Bt Lh1700w Owners Manual

11
1. Push [MENU] to display the MAIN menu. 
2. Push [ ,  ] to select the menu, then push 
[ENTER]. 3. Push [ ,  ] to select the sub menu, then push 
[ENTER]. 
The setting values in the sub menu change to green. 
4. Push [ ,  ] to select the setting values, then 
push [ENTER]. 
Push [MENU] to cancel. 
To return to the previous screen
Push [MENU].
Menu operations
MENU
MARKER
MARKER 16:9
MARKER 4:3
MARKER BACK
CENTER MARKER
GPI PRESET1
GPI PRESET2OFF
OFF
NORMAL
OFF
80%
80%
MARKER
MARKER 16:9
MARKER 4:3...

12
You can change the menu setting values and picture adjusting knob settings, then save and load up to 5 
combinations of screen adjustment values as user data. You can also return the setting values and adjustment 
values to the factory preset settings. 
The following settings are included in user data. 
 Menu settings except for “SETUP LOAD/SAVE” (including the button function settings on the front of the monitor)
 Screen adjustment values changed in picture adjusting knob
1. Push [MENU] to display...

13
Menu configuration
MAIN
VIDEO CONFIG
SYSTEM CONFIG
INPUT SELECT GPI
MARKER
GAMMA SELECT 
FILM GAMMA
COLOR TEMP.
SHARPNESS MODE
SHARPNESS H
SHARPNESS V
I-P MODE
MONO
ANAMO
SD ASPECT
SCAN
NOISE WIPE BACKLIGHT
FUNCTION1
FUNCTION2
SUB WINDOW
WFM POSITION
MENU POSITION
ROTARY POSITION
STATUS DISPLAY
SETUP LOAD
SETUP SAVE
FAN MOTOR
GPI CONTROL
GPI1
GPI2
GPI3
GPI4
GPI5
GPI6
GPI7
GPI8 VIDEO/ Y/C
NTSC SETUP
YP
BPR/RGB
COMPONENT LEVEL
RGB SYNC
COMP.
AUTOSETUP
H POSITION
V POSITION
PHASE
CLOCK
WXGA/XGA
AUDIO...

14
The underlined values are factory preset setting values. 
*1 When controlling the marker settings using the GPI function (J page 23), these settings become disabled. 
These are not operated when the 2 screens are displayed. 
*2 These are only enabled when the HD signal and SD signal aspect ratio settings are 16:9. 
*3 These are only enabled when the SD signal aspect ratio setting is 4:3. 
MARKER
Sub menu Settings Explanation
MARKER 16:9
*1*2









Used to select/display the type of marker when the...

15
g16:9 marker 
(Displayed when using HD, or when using SD 
with a 16:9 aspect ratio)
The marker is only displayed as a vertical bar. In 
addition, the   section becomes the “MARKER 
BACK” item. 
VISTA marker, CNSCO marker
A horizontal dotted line is displayed as the marker. 
When “UNDER” is set in “SCAN” in the  
“VIDEO CONFIG” menu, a vertical dotted line is also 
displayed as the marker. Area marker
A dotted line is displayed as the marker. 
g4:3 marker 
(Displayed when using SD with a 4:3 aspect...

16
The underlined values are factory preset setting values. 
*1 Even if FILM gamma is changed during 2 screen display, only the main window is set, and the changes are not 
reflected in the sub window. 
*2  When “RGB-COMP.” is selected in “YP
BPR/RGB” in the “INPUT SELECT” menu (J page 21), this does not operate.
*3 The following sharpness values can each be set, 
1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW,  
SHARPNESS H/V : 0)
2) any other input line’s HD (Factory...

17
gWB adjustment mode
You can adjust “WHITE BALANCE VAR1” – “WHITE BALANCE VAR3” (WB) by selecting “VAR1” – “VAR3” in 
“COLOR TEMP.” in the “VIDEO CONFIG” menu. 
The underlined values are factory preset setting values. 
*1 When adjusting, the item display moves to the lower part of the screen. 
The underlined values are factory preset setting values.
*2 This function is disabled while in 2 screen display mode.  
*3 These functions are disabled when the control settings are in GPI mode. 
*4 If these...

18
The underlined values are factory preset setting values.
*1 When the monitor is shipped from the factory, “USER1” – “USER5” and “FACTORY” all have the same details. 
*2 This screen is not displayed when “RGB-COMP.” is selected in the “YP
BPR/RGB” menu in the “INPUT SELECT” 
menu.
gAbout H/V DELAY
This displays the video blanking period. By pushing the button, you can switch through the H blanking display J
V blanking display J H and V blanking display J no blanking display.
SYSTEM CONFIG
Sub menu...

19
gAbout the SUB WINDOW
You can compare saved still and moving images or show the Wave Form Monitor (WFM) by using the “SUB 
WINDOW” function to separate the main window into 2 displays as shown below.
Depending on the settings of the “SUB WINDOW” (FULL, PART, WFM) in the “SYSTEM CONFIG” menu  
(J page 18) it can be switched as shown below.
Every time you press the [FUNCTION1] (or [FUNCTION2]) button (J page 17) assigned to the “SUB WINDOW” 
function, the window switches (To use the “SUB WINDOW”...

20
The “GPI CONTROL” item is used to set enable/disable of all GPI functions, and assigns functions to each of the 
GPI terminal pins (J page 23). 
The underlined values are factory preset setting values. 
Note: 
Please be aware that the following can not be performed. 
“SD ASPECT” operation when input signal is HD or PC
“SCAN” operation when the input signal is PC
“GAMMA SELECT” operation when the input signal is PC
“RGB SYNC” operation when anything other than “RGB-VIDEO” is selected in “YP...