Panasonic Marine Case Dmw-mctz30 Operating Instructions

11VQT4C30
2Check the O-ring.
≥Check that there is no dirt, sand, hair, dust, salt crystals, lint or grease on the 
O-ring. If you find any of these, remove them with a soft, dry cloth.
≥There may be dirt on the O-ring that you cannot see. Check if there is any dirt by 
rubbing your finger over the O-ring.
≥Be careful not to leave any fibers from the dry cloth on the O-ring when wiping it.
≥Check that the O-ring is not ripped, twisted, squashed, frayed or scratched and 
that there is no sand sticking to...

12VQT4C30
Preparation -Setting the O-ring- (continued)
4Apply the grease (supplied).
Apply O-ring grease to clean the surface of the O-ring and replenish the oil.
≥Apply a rice-grain size of grease (supplied) evenly to the O-ring with the tip of 
your finger. (Do not apply the grease with paper or a cloth. The fibers from the 
paper or cloth may stick to the O-ring.)
≥If there is too much grease on the O-ring, dirt and dust will stick to it causing 
water to leak in. Therefore, hold the O-ring between...

13VQT4C30
6Inspect the O-ring one last time.
Check the following one more time:
≥There is no dirt sticking to the O-ring.
≥The O-ring has not come out.
≥The O-ring is not twisted.
≥There are no scratches or squashed parts on the O-ring.
Thoroughly wipe any grease off your hands with a dry cloth. Afterwards 
wash thoroughly with fresh water.
7Close the buckle.
≥Check that no foreign materials are sticking to the outer surface of the O-ring or 
the buckle on the front case and then close the Case.
∫Notes...

14VQT4C30
Preparation -Checking the Case is Waterproof-
After setting the O-ring, check that no water leaks into the Case by 
submerging it in a water tank, bath tub etc. for about 3 minutes before 
attaching a digital camera.
≥Do not use the Case in water over 40 °C/104 °F. The heat may damage the Case or 
cause water leakage.
‘Carry out the same test after attaching the digital camera to the Case. (P15)
∫Notes
≥If bubbles rise from the Case when it is submerged in water or there is water inside 
the...

15VQT4C30
Preparation -Attaching the Digital Camera-
Read the notes on page 17 before attaching the digital camera.
Check that the ON/OFF Switch on the camera and the case is set to 
[OFF], and [Rec]/[Playback] selector switch is set to [
!].
≥Remove the strap from the digital camera.
1Push 2 up with your finger while sliding 1 to open the buckle.
2Attach the digital camera to the Case.
≥Be careful not to catch the shading hood  1.
3Insert the silica gel (supplied).
≥Always use new silica gel. 
Silica...

16VQT4C30
Preparation -Attaching the Digital Camera- (continued)
≥When inserting the silica gel, bend it as shown in the illustration below 
and then insert it as far as possible. If you close the Case with the silica 
gel not fully inserted, the silica gel will get caught in the O-ring causing 
water leakage.
≥If the air temperature is high and the water temperature is low, condensation 
may appear inside the Case. To prevent condensation, insert silica gel 
(supplied) inside the Case in advance. To...

17VQT4C30
∫Notes
≥Be careful not to get the shading hood dirty with fingerprints etc.≥Check one more time that the O-ring is fitted evenly into the O-ring groove.≥Avoid opening or closing the Case where ther e is a lot of sand or dust and in humid 
or wet places.
≥If there is a sudden change of humidity caused by moist air entering the Case, 
condensation may appear inside the Case.
≥To prevent condensation, set the digital camera in as dry a place as possible. Also, 
check that the silica gel (supplied)...

18VQT4C30
Taking Pictures
∫Be sure to check the following before entering the water
Check the following before diving.
≥Is there sufficient remaining battery power?
≥Is there sufficient memory in the card?
≥Is the O-ring fitted evenly into the O-ring groove?
≥Have you checked that no water leaks into the Case?
≥Is the buckle closed firmly?
∫Taking pictures
1Turn the camera on.
2Display the scene mode menu and then set [Underwater].
3Aim the AF area on the LCD monitor at the subject you want to focus...

19VQT4C30
Tips for Taking Pictures in the Water
It is recommended to use the scene mode (underwater) appropriate for underwater 
when recording underwater.
It may not be possible to record images with intended brightness or color depending on 
the recording conditions (depth/weather/subject), so try using following functions 
together.
It is recommended to use burst function to record subject that is moving fast, etc.
∫Note
≥
For details of white balance fine adjustment  (underwater mode) or other...

20VQT4C30
After Use
After you have finished taking pictures, follow the steps below.
1Submerge the Case in fresh water for about 30 minutes or more 
without removing the digital camera to remove any salt crystals etc.
≥Press all the operation buttons etc. on the Case to wash away any 
seawater. If the salt crystals are not removed from the buttons etc., they 
will harden and the buttons will become inoperable.
≥Do not wash the Case with fast-running or pressurized water etc. as it may 
cause water...