Home > Panasonic > Camera Accessories > Panasonic Marine Case Dmw-mctz10 Operating Instructions

Panasonic Marine Case Dmw-mctz10 Operating Instructions

Here you can view all the pages of manual Panasonic Marine Case Dmw-mctz10 Operating Instructions. The Panasonic manuals for Camera Accessories are available online for free. You can easily download all the documents as PDF.

Page 11

11VQT2N71
2Check the O-ring.
≥Check that there is no dirt, sand, hair, dust, salt crystals, lint or grease on the 
O-ring. If you find any of these, remove them with a soft, dry cloth.
≥There may be dirt on the O-ring that you cannot see. Check if there is any dirt by 
rubbing your finger over the O-ring.
≥Be careful not to leave any fibers from the dry cloth on the O-ring when wiping it.
≥Check that the O-ring is not ripped, twisted, squashed, frayed or scratched and 
that there is no sand sticking to...

Page 12

12VQT2N71
Preparation -Setting the O-ring- (continued)
4Apply the grease (supplied).
Apply O-ring grease to clean the surface of the O-ring and replenish the oil.
≥Apply a rice-grain size of grease (supplied) evenly to the O-ring with the tip of 
your finger. (Do not apply the grease with paper or a cloth. The fibers from the 
paper or cloth may stick to the O-ring.)
≥If there is too much grease on the O-ring, dirt and dust will stick to it causing 
water to leak in. Therefore, hold the O-ring between...

Page 13

13VQT2N71
6Inspect the O-ring one last time.
Check the following one more time:
≥There is no dirt sticking to the O-ring.
≥The O-ring has not come out.
≥The O-ring is not twisted.
≥There are no scratches or squashed parts on the O-ring.
Thoroughly wipe any grease off your hands with a dry cloth. Afterwards 
wash thoroughly with fresh water.
7Close the buckle.
≥Check that no foreign materials are sticking to the outer surface of the O-ring or 
the buckle on the front case and then close the Case.
∫Notes...

Page 14

14VQT2N71
Preparation -Checking the Case is Waterproof-
After setting the O-ring, check that no water leaks into the Case by 
submerging it in a water tank, bath tub etc. for more than about 
3 minutes before attaching a digital camera.
≥Do not use the Case in water over 40 °C/104 °F. The heat may damage the Case or 
cause water leakage.
‘Carry out the same test after attaching the digital camera to the Case. (P15)
∫Notes
≥If bubbles rise from the Case when it is submerged in water or there is water...

Page 15

15VQT2N71
Preparation -Attaching the Digital Camera-
Check that the ON/OFF Switch on the camera and the case is set to 
[OFF], and [REC]/[PLAYBACK] selector switch is set to [!].≥Remove the strap from the digital camera.
1Push 2 up with your finger while sliding 1 to open the buckle.
2Attach the digital camera to the Case.
≥Be careful not to catch the shading ring  1.
3Insert the silica gel (supplied).
≥Always use new silica gel. 


Silica gel
Digital Camera
DMW-MCTZ10-VQT2N71.book  15 ページ...

Page 16

16VQT2N71
Preparation -Attaching the Digital Camera- (continued)
≥When inserting the silica gel, bend it as shown in the illustration below 
and then insert it as far as possible. If you close the Case with the silica 
gel not fully inserted, the silica gel will get caught in the O-ring causing 
water leakage.
≥If the air temperature is high and the  water temperature is low, condensation 
may appear inside the Case. To prevent condensation, insert silica gel 
(supplied) inside the Case in advance. To...

Page 17

17VQT2N71
∫Notes
≥Check one more time that the O-ring is fitted evenly into the O-ring groove.≥Avoid opening or closing the Case where ther e is a lot of sand or dust and in humid 
or wet places.
≥If there is a sudden change of humidity caused by moist air entering the Case, 
condensation may appear inside the Case.
≥To prevent condensation, set the digital camera in as dry a place as possible. Also, 
check that the silica gel (supplied) is sufficiently dry before inserting.
≥If sunscreen or suntan oil...

Page 18

18VQT2N71
Taking Pictures
∫Be sure to check the following before entering the water
Check the following before diving.
≥
Is there sufficient remaining battery power?
≥Is there sufficient memory in the card?
≥Is the O-ring fitted evenly into the O-ring groove?
≥Have you checked that no water leaks into the Case?
≥Is the buckle closed firmly?
∫ Taking pictures
1Turn the camera on.
2Display the scene mode menu and then set [UNDERWATER].
≥
Read the operating instructions of the digital camera for details....

Page 19

19VQT2N71
Tips for Taking Pictures in the Water
When the image is too bluish in the water
1
Press 3 ( ) several times until [ ] appears.
2Press 2 (AF-L)1 ()  to adjust the white balance.
3Press [MENU/SET] to finish.
≥You can also press the shutter button halfway to finish.
Select the best picture
Set the flash to [ ].
Using the Auto Bracket Function (For models with an Auto Bracket Function)
≥Each time the shutter button is pressed,  3 pictures with different exposures are 
automatically recorded. You...

Page 20

20VQT2N71
After Use
After you have finished taking pictures, follow the steps below.
1Submerge the Case in fresh water for about 30 minutes or more 
without removing the digital camera to remove any salt crystals etc.
≥
Press all the operation buttons etc. on the Case to wash away any 
seawater. If the salt crystals are not removed from the buttons etc., they 
will harden and the buttons will become inoperable.
≥Do not wash the Case with fast-running or pressurized water etc. as it may 
cause water...
Start reading Panasonic Marine Case Dmw-mctz10 Operating Instructions

Related Manuals for Panasonic Marine Case Dmw-mctz10 Operating Instructions

All Panasonic manuals