Panasonic LCD Projector Pt Lx300 Operating Instructions

							Setting up
ENGLISH - 21
Getting Started
Calculation formulas for projection distance Q
Any other projection distance can be obtained according to the screen dimensions (m) using the following 
calculations. The calculation result is with the "m" unit. (The calculated distance below may contain a certain 
error.) If the screen dimensions are written as "SD",
For 4:3 aspect ratioFor 16:9 aspect ratio
Screen height (SH)= SD × 0.6= SD × 0.490
Screen width (SW)= SD × 0.8= SD × 0.872
Min. projecion distance (LW)= 1.56 × SD= 1.70 × SD
Max. projecion distance (LT)= 1.74 × SD= 1.90 × SD
Adjusting the Projector's Height
The projector is equipped with elevator feet for adjusting the image height.
Extend the adjustable feet by rotating in the direction shown in the below picture and retract by rotating in the op-
posite direction.
Adjustable range:12 mm (0.47")
The front adjustable feet stretch to its end The rear adjustable feet stretch to its end
3.7 °3.7 °
Attention
Hot air is expelled from the air exhaust port. Do not touch the air exhaust port directly when adjusting the adjustable feet. z
Adjusting the zoom and focus
Turn the zoom lever and the focus ring to adjust the image.
Focus RingZoom Lever
Note
It is recommended that the images are projected continuously for at leas\
t 30 minutes before the focus is adjusted. z
As the projection screen size changes if the focus ring is turned, turn the zoom ring to fine-tune the projection screen size  z
again. 
						

							22 - ENGLISH
Getting Started
Connections
Before connecting to the projector
Read carefully the instruction manual for the device to be connected. z
Turn off the power switch of the devices before connecting cables. z
If any connection cable is not supplied with the device, or if no optional cable is available for connection of the  z
device, prepare a necessary system connection cable to suit the device.
Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture.   z
In this case, a time base corrector (TBC) must be connected.
The projector accepts the following signals: VIDEO, analogue-RGB (with TTL sync. Level) and digital signal. z
Some computer models are not compatible with the projector. z
When using long cables to connect with each of equipment to the projector , there is a possibility that the image  z
will not be output correctly unless a compensator is used.
For details on what video signals the projector supports, see “List of compatible signals”. ( zÆpages 53-54)
Attention
When connecting with a video deck, be sure to use the one with a built-in time base corrector (TBC) or use a  TBC between  z
the projector and the video deck.
If nonstandard burst signals are connected, the image may be distorted. If this is the case, connect a TBC between the  z
projector and the video deck.
Note
Use an HDMI cable that conforms to HDMI standards such as an HDMI High Speed cable. If a cable that does not meet  z
HDMI standards is used, video may be interrupted or may not be displayed.  
When connecting the 1080p signal using HDMI, use a cable compliant with 1080p signal.
This projector does not support the VIERA Link (HDMI). z 
						

							Connections
ENGLISH - 23
Getting Started
Connecting example: Computers
Monitor
Computer Computer Control
Computer Audio equipment
Connecting example: AV equipment
Blu-ray disk 
playerDVD player VCR
(with built-in TBC)Audio equipment 
						

							Powering ON/OFF
24 - ENGLISH
Basic Operation
Powering ON/OFF
Basic Operation
Connecting the power cord
Use the supplied power cord to prevent removal of the power cord and mak\
e sure that it is fully 
inserted into the projector.
For detailed power cord handling, refer to “Read this first!” (Æ pages 2 to 6).
Attaching J
Check the shapes of the  terminal on the back side of the project\
or and the 1 ) 
power cord connector and fully insert.
Connect the power plug to an outlet.2 ) 
Removing J
Confirm that the projector is in standby mode and unplug the power cord from the 1 ) 
outlet.
Remove the plug from the  terminal.2 )  
						

							Powering ON/OFF
ENGLISH - 25
Basic Operation
ON(G)/STANDBY(R) indicator
The ON(G)/STANDBY(R) indicator informs you the status of the power. Confirm the status of the  
 indicator before operating the projector.
 indicator 
Indicator statusStatus
No illumination or blinkingThe power plug is not connected to the outlet.
Red
Lit1The power is switched off. (Standby mode)
Press  to start projection.
Slow 
Blinking2The power is switched off. (Standby mode)
Press  to start projection.
BlinkingThe projector is preparing to switch off the power.
The power is switched off after a while. (Changes to the standby mode.)
GreenLitThe projector is in the projection status.
BlinkingThe projector is preparing for projection.
1 When [VGA Out (Standby)]/[In Standby Mode (Audio)] are all set to [Off].
2  When one or more among [VGA Out (Standby)]/[In Standby Mode (Audio)] is/are set to [On].
Note
When the  indicator is blinking in red, the internal fans start to operate and the projector starts  z
cooling. 
						

							Powering ON/OFF
26 - ENGLISH
Basic Operation
Powering On the Projector
Connect the power plug to the power outlet.1 ) 
Enter Standby status when the  indicator is lighting / blinking in red. z
Press the  button on the control panel or the remote control.
When the  indicator lights up in green, the lamp is on. z
Startup screen is displayed for about 10 seconds, then the image will be projected.  z
OR
Note
If the power is disconnected due to the power breaker during projection at the last use, ON(G)/STANDBY(R) indicator will  z
light in green automatically at the next startup and the image will be projected. 
Powering Off the Projector
Press the  button on the control panel or the remote control.
The following message appears. z
Message will disappear after about 30 seconds when there is no operation.  z
Press the  button again.
The projection stops and the  indicator on the projector flashes up in red. (Fan is  z
still spinning.)
Wait until the  indicator lights / blinks in red (The fan stops 3 ) 
spinning).
The projector enters standby mode when the  indicator lights / blinks in red. z
Note
Do not turn on the power and project images immediately after turning the projector off. Turning on the power while the  z
lamp is still hot may shorten the lamp life.
Make sure that the projector is cool enough if you want to pack it for transportation and storage. z 
						

							Projecting
ENGLISH - 27
Basic Operation
Projecting
Check the connections of the peripheral devices and connection of the power cord (Æpage 24) and switch on the 
power (Æpage 26) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
Press  button on the control panel or the , 
, ,  on the remote control.
The image of the signal being input in the selected terminal is projecte\
d. z
Press  button to display the [Source] menu. Press   z
▲▼ to select the desired input and press ► to enter.
 
 
How to adjust the state of the image
Adjust the projection angle.1 ) 
Place the projector parallel to the screen, and then install it on a flat surface so that the screen becomes  z
rectangle.
If the image is tilted lower than the screen, extend the adjustable feet to make a rectangle screen. z
For details, see “Adjusting the Projector's Height” ( zÆpage 21).
Adjust the zoom and the focus.2 ) 
Turn the zoom lever and the focus ring to adjust the image.
Focus RingZoom Lever
Note
It is recommended that the images are projected continuously for at leas\
t 30 minutes before the focus is adjusted. z
If keystone distortion occurs, see [V Keystone] in the [Position] menu ( zÆpage 36). 
						

							Basic operation by using remote control
28 - ENGLISH
Basic Operation
Basic operation by using remote control
Switching the input signal
Press this button to switch input signals.
 Buttons
Press (, ,  
button on the remote control.
COMPUTERSwitches to Computer input.
HDMI Switches to HDMI input.
VIDEOSwitches to Video input. 
Note
For details, see “Selecting the input signal”. ( zÆpage 27)
 button
Press this button to display the [Lamp Power Mode] 
menu. 
 Button
Press the  button on the remote 
control.
Note
For details, see “Lamp Power Mode”. ( zÆpage 41)
 z
 button
Press this button to display the [Information] menu. 
 Button
Press the  button on the remote 
control.
Note
For details, see “Information”. ( zÆpage 41)
 button
This function allows you to temporarily freeze 
the picture on the screen of the external devices, 
meanwhile, volume is muted. 
 Button
Press the  button on the 
remote control.
Fig.1 will appear on the screen while the Freeze  z
function is working.
Note
To cancel the Freeze function, press the   z
button again.
 button
This function allows you to correct keystone distortion.
 Buttons
Press the  or  
buttons on the remote control.
Note
For details, see [V Keystone] in the [Position] menu  z
(Æpage 36)  
 
 
 
 
Fig. 1 
						

							Basic operation by using remote control
ENGLISH - 29
Basic Operation
 button
Press this button to display the [Picture mode] menu 
and to change the settings of the image.
 Button
Press the  button on the remote 
control.
Note
For details, see [Color Mode] menu of [Picture] menu  z
(Æpage 32)
 button
Press this button to display the [Input] menu and to 
switch to the desired input signal.
 Button
Press the  button on the remote 
control.
Note
For details, see “Selecting the input signal”. ( zÆpage 27)
 button
Press this button to display the main menu and to 
return to the main menu from the submenu.
 Button
Press the  button on the remote 
control.
Note
For details, see “On-screen Display Menus”.   z
(Æpage 31-32)
 button
Press this button to optimize to the best image quality 
during the computer input signal.
 Button
Press the  button on the 
remote control.
Note
The  operation may not optimize the image  z
position or the resolution, depending on the input signal 
format or the image contents. In this case, switch to a 
different image and execute  again.
 button
Press this button to temporarily turn off the sound.
 Button
Press the  button on the remote 
control. 
Note
To turn the sound back on, press the  button  z
again or press the  buttons. (Æpage 39)
 button
Press this button to display the [Position] menu and to 
change the aspect settings.
 Button
Press the  button on the 
remote control.
Note
For details, see [Aspect Ratio] of [Position] menu.   z
(Æpage 35) 
 button
Press this button to temporarily black out the image 
and turn off the sound.
 Button
Press the < AV MUTE> button on the 
remote control.
Note
Press the  button again to cancel. z
 buttons
Press the buttons to display [Volume] menu and to 
adjust the volume of the build-in speaker.
 Buttons
Press the  buttons on the 
remote control.
Note
For details, see [Volume] of [Audio] menu. ( zÆpage 39) 
						

							On-screen Display Menus
30 - ENGLISH
Settings
How to operate menu
Operation steps J
Press  button on the remote control or on the control panel.1 ) 
Main Menu displays. z
Use ▲▼ to select any item in the Main Menu.2 ) 
The selected item is highlighted in orange. z
Press 3 ) ►.
Items in the Sub Menu can be selected. z
Use ▲▼ to select any item in the Sub Menu.4 ) 
The selected item is highlighted in yellow.  z
Press 5 ) ► to display adjusting box.
Use ▲▼ to switch or adjust all settings.6 ) 
Press  button to go back to the Sub Menu and press again to go bac\
k to the 7 ) 
Main Menu, press  button once more to close the Main Menu.
Note
Some items may not be adjusted or used for certain signal formats input to the projector. The MENU items that cannot be  z
adjusted or used are shown in gray characters, and they cannot be selected.
Some items can be adjusted even if signals are not input. z
If there is no operation to the projector for about 30 seconds, the Menu screen and the adjusting screen will disappear  z
automatically.
See pages 31 and 32 for details on the items of Sub Menu. z
Main Menu
Sub Menu
Setting Value
or
Adjusting Value
On-screen Display Menus
Settings