Panasonic LCD Projector PT-LB10NTU PT-LB10U PT-LB10VU PT-LB10SU Operating Instructions

ENGLISH-11
Preparation
Before use
Caution when moving the projector
Be sure to attach the lens cover before moving the projector.
The projection lens is extremely susceptible to vibration and shocks. When
moving the projector, use the accessory carrying bag. When placing the
projector inside the carrying bag, position it so that the lens is facing upward.
Do not put anything else in the bag other than the projector and the cables.
Cautions regarding setting-up
Avoid setting up in places which are subject...

12-ENGLISH
Notes on use
In order to get the best picture quality
Draw curtains or blinds over any windows and turn off any fluorescent lights
near the screen to prevent outside light or light from indoor lamps from
shining onto the screen.
Do not touch the surfaces of the lens with your bare hands.
If the surface of the lens becomes dirty from fingerprints or anything else, this
will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it...

ENGLISH-13
Preparation
Location and function of each part
#Projector control panel (page 16)
$Zoom ring (page 25)
%Focus ring (page 25)
&Security lock 
This can be used to connect a commercially-available theft-prevention
cable (manufactured by Kensington). This security lock is compatible with
the Microsaver Security System from Kensington.
'Leg adjuster buttons (L /R) (page 25)
These buttons are used to unlock the front adjustable legs. Press to adjust
the angle of tilt of the projector.
(Lens...

14-ENGLISH
#Connector panel (page 15)
$Air outlet port
Do not cover this port.
%Speaker
&Front adjustable legs (L /R) (page 25)
'Air inlet port, Air filter (page 52)
Do not cover this port.
(Lamp unit holder (page 53)
WARNING
Do not place your hands or other objects close to the air outlet port.
BHeated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
Projector 
NOTE:
BDuring...

ENGLISH-15
Preparation
Connector panel
#Power input socket (AC IN) (page 24)
The accessory power cord is connected here.
Do not use any power cord other than the accessory power cord.
$SERIAL connector (pages 21, 22 and 62)
This connector is used to connect a personal computer to the projector in
order to control the projector externally. (RS-232C compatible)
%RGB IN connector (pages 21 and 22)
This connector is used to input RGB signals and YP
BPRsignals.
&RGB OUT connector (page 21)
This connector is...

16-ENGLISH
Menu
operation

Remote control unit
FREEZESHUTTER
INDEX
WINDOW
PROJECTORSTD AUTO
SETUPINPUT POWER
MENU
ENTER
VIDEO RGB
VOLUMED.ZOOM
'
(
+
-
./
0
12
,
)
*
Projector control panel 



 

	 

ENGLISH-17
Preparation
#RGB INPUT indicator
This indicator illuminates when a signal is being input to the RGB IN
connector.
$LAMP indicator (page 51)
This indicator illuminates when it is time to replace the lamp unit. It flashes
if a circuit abnormality is detected.
%TEMP indicator (page 50)
This indicator illuminates if an abnormally high temperature is detected inside
the projector or around it. If the temperature rises above a certain level, the
power supply will be turned off automatically and the...

%
$
#
18-ENGLISH
Inserting the wireless card (PT-LB10NTU only)
Insert the wireless card before using the PT-LB10NTU.
Hexagon wrench
(accessory)
Card lock fixing
screw#Insert the wireless card until it
locks.
$Set the card lock.
%Fasten the card lock with the card
lock fixing screw using the
hexagon wrench. The card lock is already installed at the factory default setting. When you
insert the wireless card, first remove the card lock fixing screw using the
hexagon wrench to release the card lock.
BWhen...

ENGLISH-19
Getting started
Setting-up
Projection methods
In way of installing projector, any one of the following four projection methods
are used. Select whichever projection method matches the setting-up
method. (The projection method can be set from the “OPTION2” menu. Refer
to page 45 for details.)
BFront-desk projectionBFront-ceiling projection
BRear-desk projection
(Using a translucent screen)BRear-ceiling projection
(Using a translucent screen)
Menu items Setting
FRONT
DESK FRONT/REAR...

H1L
LSH
SW
81.2
 (3-3/16)
20-ENGLISH
NOTE:
BThe dimensions in the table above are approximate.
BIf you use the projection distance for the 16:9 screen,
the 4:3 projection image overflows the screen at the top
and bottom.
BFor details about projected image distances, refer to
page 61.
Projector position
L: Projection distance
SH: Image height
SW: Image width
H1: Distance from center
of lens to bottom edge
of projected image Top edge of screen
Screen
Bottom edge of screen
Screen
Projection distances

0.84...