Panasonic LCD Projector PT-FW430U PT-FX400U Operating Instructions

							DISPLAY OPTION menu
ENGLISH - 51
Settings
CLOSED CAPTION SETTING
[Only for NTSC, 525i (480i) input]
Set the closed caption display as follows.
Press ▲▼ to select [CLOSED 
1  ) 
CAPTION SETTING].
Press the  button.
2  ) 
The [CLOSED CAPTION SETTING] screen is  
z
displayed.
Press ▲▼to select, and press ◄► to 
3  ) 
switch.
CLOSED CAPTION 
J
Displays or hides the closed caption.
Each press of the button switches the settings as 
 
z
shown below.
When you set the function to [ON], a message, 
 
z
[If the input matches the CC type selected, the 
SECURITY TEXT/LOGO will not be displayed], is 
displayed on the screen. Select [OK] or [CANCEL], 
and press the  button.
OFFON
OFF Turns off closed caption display
ON Turns on closed caption display
MODE 
J
Selects a closed caption mode.
Each press of the button switches the settings as 
 
z
shown below.
CC1CC2
CC4CC3
CC1  Displays CC1 data
CC2  Displays CC2 data
CC3  Displays CC3 data
CC4  Displays CC4 data
Note
The closed caption is mainly used in the north America. 
 
z
This function shows the text information contained in the 
image signal. Captions may not be displayed on some 
devices or software.
You can select [CLOSED CAPTION] only when NTSC or 
 
z
525i (480i) signals are input.
Security messages (security texts and user logo) are not 
 
z
displayed when the closed caption signal of the selected 
mode is input. (
Æpage 65)
Part of characters may not be displayed when high 
 
z
compensation values are set in [KEYSTONE].
Closed captions are not displayed while the menu screen 
 
z
appears.
SCREEN SETTING 
[PT-FW430U only]
When the projection image aspect ratio is changed, 
the projector makes corrections to ensure the optimal 
images for the set screen size.
Set this in accordance with the screen you are using.
Press ▲▼ to select [SCREEN 
1  ) 
SETTING].
Press the  button.
2  ) 
The [SCREEN SETTING] screen will be  
z
displayed.
Press ▲▼ to select items and ◄► to 
3  ) 
switch settings.
SCREEN FORMAT 
J
Each press of the button switches the settings as  
z
shown below.
16:916:10
16:9 For screens with a 16:9 aspect ratio
16:10 For screens with a 16:10 aspect ratio
SCREEN POSITION 
J
Each press of the button switches the settings as  
z
shown below.
LOWCENTERHIGH
LOW Displays the projected image in 
the lower part of the screen
CENTER Displays the projected image in 
the center part of the screen
HIGH Displays the projected image in 
the top part of the screen
Note
[SCREEN POSITION] cannot be adjusted when [16:10] 
 
z
is selected for [SCREEN FORMAT]. 
						

							DISPLAY OPTION menu
52 - ENGLISH
Settings
STARTUP LOGO
Sets the logo that is projected when the power is 
turned on.
Press ▲▼ to select [STARTUP LOGO].
1  ) 
Press ◄► to switch [STARTUP LOGO]
2  ) 
The setting changes as follows each time the  
z
button is pressed.
DEFAULT LOGOTEXT
OFFUSER LOGO
DEFAULT 
LOGOThe Panasonic logo is projected
TEXT The input text is projected
USER LOGO The logo transferred by “Logo 
Transfer Software *
1 ” is projected
OFF No startup logo is projected
“Logo Transfer Software” is included on the 
*1 : 
supplied CD-ROM.
Note
When [TEXT] is selected, input text is projected. You can 
 
z
input up to two lines with 40 characters in each line.
The STARTUP LOGO disappears after 30 seconds.
 
z
Editing text 
J
Press ◄► to select [TEXT], then press 
1  ) 
the  button.
The [STARTUP LOGO] screen appears. 
z
Press ▲▼ to select the item
2  ) 
Input text to be displayed on the first line in  
z
[TEXT 1] and text for the second line in [TEXT 
2].
5&951586
0, $/$&-
5&95
3&563/
&/5&3
4&-&$5
Press the  button.
3  ) 
The [TEXT CHANGE] screen appears. 
z
To input a character, press ▲▼◄► 
4  ) 
to select the character, then press the 
 button.
If you select [ALL DELETE], you can erase  
z
all the input text. If you press the [DEFAULT] 
button of the remote controller, you can erase 
the character currently selected by the cursor in 
the input box.
--
%&-&5&
1586Ù
41$&
A
BCD EFG H IJK LM
N O PQ RSTU VW XY Z
a b cd e fg h ijk lm
n o p q rs tu vw xyz
1 234567890
! “ #$% &‘ *+� /＝ ?
_ `|~ ()< > []{ } ,
5&95
$)/(&
$/$&-
0,
%&-&5&
3&563/
&/5&3
4&-&$5
Select [OK], then press the  
5  ) 
button.
On the [STARTUP LOGO] screen, 
6  ) 
select [OK], then press the  
button.
To cancel text input, select [CANCEL]. 
z
AUTO SETUP
Set this to [AUTO] under normal circumstances.
Press ▲▼ to select [AUTO SETUP].
1  ) 
Press ◄► to switch [AUTO SETUP].
2  ) 
The setting changes as follows each time the  
z
button is pressed.
AUTOBUTTON
AUTO Adjusts the projected image 
position automatically when the 
projected signals are switched to the 
COMPUTER signals.
BUTTON Adjusts the projected image position 
only when the [AUTO SETUP] 
button is pressed. (
Æpage 33)  
						

							DISPLAY OPTION menu
ENGLISH - 53
Settings
SIGNAL SEARCH
When the power is turned on, this function 
automatically detects the terminal to which signals are 
input and sets the projection settings.
Press ▲▼ to select [SIGNAL 
1  ) 
SEARCH].
Press ◄► to switch [SIGNAL 
2  ) 
SEARCH].
The setting changes as follows each time the  
z
button is pressed.
ONOFF
ON Enables automatic input detection.
OFF Disables automatic input detection.
Note
When the AUTO SETUP button on the remote control 
 
z
is pressed and no projecting signal is input, SIGNAL 
SEARCH is enabled.
BACK COLOR
Sets the color of the projection screen when no signal 
is input.
Press ▲▼ to select [BACK COLOR].
1  ) 
Press ◄► to switch [BACK COLOR].
2  ) 
The setting changes as follows each time the  
z
button is pressed.
BLUEBLACK
USER LOGODEFAULT LOGO
BLUE The entire projection area appears 
blue.
BLACK The entire projection area appears 
black.
DEFAULT  LOGO The Panasonic logo is projected.
USER LOGO The logo transferred by “Logo 
Transfer Software *
1 ” is projected.
“Logo Transfer Software” is included on the 
*1 : 
supplied CD-ROM.
WIDE MODE
This function is used when WXGA, WXGA+, 
WXSGA+, or WUXGA signals are input.
Press ▲▼ to select [WIDE MODE].
1  ) 
Press ◄► to switch [WIDE MODE].
2  ) 
The setting changes as follows each time the  
z
button is pressed.
AUTOOFFON
AUTO Switches the setting automatically.
OFF When inputting 4:3 signals
ON When inputting wide signals
SXGA MODE
This function is used when the projected image of 
SXGA signal extends outside of the screen.
Press ▲▼ to select [SXGA MODE].
1  ) 
Press ◄► to switch [SXGA MODE].
2  ) 
The setting changes as follows each time the  
z
button is pressed.
SXGASXGA + 
SXGA Normal setting
SXGA + Set this when the edge of the image 
is cropped 
						

							DISPLAY OPTION menu
54 - ENGLISH
Settings
OTHER FUNCTIONS
 
JAUTO SETUP
See “Adjusting the display position automatically”. 
(
Æpage 33)
 
JFREEZE
You can pause the projection and mute the sound 
temporarily, regardless of the playing status of the 
connected device.
Pressing the  button cancels the 
function.
 
JAV MUTE
You can stop the projection and the sound when 
you will not be using the projector for a while.
Pressing the  button cancels the 
function.
 
JINDEX WINDOW
You can capture the projected image and store it 
to memory as a still image. You can also project 
the still image and movie simultaneously in split-
window display.
Pressing the  button cancels the 
function.
The projected image at the time you press INDEX 
WINDOW is captured as a still image.
Still imageMovieMovie
Button function while INDEX WINDOW is 
displayed
Press the ▲▼ 
buttons to set the 
window size
(The size of the window 
can be set in three ways 
for the PT-FX400U, 
and two ways for the 
PT-FW430U.)
Movie
Still image
Movie
Still image
Press the ◄► 
buttons to switch the 
positions of the still 
image and movie 
right or left.
Movie
Still image
Still image
Movie
Note
The aspect ratio is adjusted. Consequently, the image is 
 
z
stretched vertically.
If you change the size of window, the aspect ratio is 
 
z
adjusted. (
Æpage 44)
Press the  button to capture a new still image.
 
z
When you capture from a movie with quick motion, the 
 
z
still image may be distorted.
When you set the aspect ratio to [REAL], the image may 
 
z
not be stretched vertically depending on the property of 
the signals. 
						

							DISPLAY OPTION menu
ENGLISH - 55
Settings
 
JDIGITAL ZOOM
%*(*5-
;00. 1.5
You can enlarge the center area.
You can also change the location of the area to be 
enlarged.
Pressing the  button cancels the 
function.
%*(*5-
;00.1.0%*(*5-
;00.3.0
Button functions during DIGITAL ZOOM
Pressing the ►button increases magnification
Pressing the ◄button decreases magnification
►button
◄button
After setting the magnification, press the  
button.
Pressing the ▲▼buttons moves the area to the top 
or the bottom.
Pressing the ◄► buttons moves the area to the 
left or the right.
Note
Magnification can be set from 1.0x to 2.0x in 0.1 
 
z
increments. When [FRAME LOCK] in the [POSITION] 
menu is set to [OFF], you can also adjust the 
magnification from 1.0x to 3.0x. When the setting 
mentioned above is [ON], you can adjust the 
magnification from 1.0x to 2.0x.
When the input signals change during DIGITAL ZOOM, 
 
z
the DIGITAL ZOOM function will be cancelled.
When DIGITAL ZOOM is active, the FREEZE function is 
 
z
not available.
 
JSIDE BY SIDE
[PT-FW430U only]
Two different input signals can be simultaneously 
projected.
Pressing the  button cancels the 
function.
Input AInput BInput AInput AInput A
Button functions during a SIDE BY SIDE 
projection
When you press ▲▼, the list of available input 
sources is displayed.
Press ▲▼ to select the image to show on the right 
side of the screen (Input B) against the left side 
of the screen (Input A), and press the  
button.
COMPUTER S-VIDEOVIDEO
NETWORKHDMIDVI
The input will be skipped if it cannot be switched 
: 
½
to.
Note
You can cancel the SIDE BY SIDE function pressing the 
 
z
, , , , 
, or  button.
[FREEZE] and [VOLUME] are set to the Input A.
 
z
While the SIDE BY SIDE function is activated, [AUTO 
 
z
SETUP], [INDEX WINDOW], and [DIGITAL ZOOM] are 
not available.
While the SIDE BY SIDE function is activated, you can 
 
z
not adjust or set the MENU items.
[PICTURE] settings can be set individually for Input A 
 
z
and Input B. (The value of [DAYLIGHT VIEW] for Input A 
is applied to both inputs.)
The aspect ratio selected in the ASPECT menu is 
 
z
maintained during a SIDE BY SIDE projection, except for 
COMPUTER signals and NETWORK signals.
Depending on the combination of input signals, SIDE BY 
 
z
SIDE projection may not be available.
For details, see “Two window display combination list” 
 
z
(
Æpage 82). 
						

							56 - ENGLISH
Settings
PROJECTOR SETUP menu
Select [PROJECTOR SETUP] from the Main 
Menu (see “Navigating through the menu” on 
page 35), then select the item from the sub-
menu.After selecting the item, press ◄►▲▼ to set.
 
z
Remote ControlControl Panel
STATUS
Displays the status of the projector.
Press ▲▼ to select [STATUS].
1  ) 
Press the  button.
2  ) 
The [STATUS] screen appears. 
z
SIGNAL NAME Displays the input signal name.
SIGNAL  
FREQUENCY Displays the frequency of the 
input signal.
PROJECTOR   RUNTIME Displays the projector runtime.
LAMP Indicates the number of hours 
the lamp has been used
SERIAL  
NUMBER Displays the serial number of the 
projector.
PROJECTOR ID
The projector has an ID number setting function that 
helps the user to control two or more projectors either 
simultaneously or separately with a single remote 
control.
Press ▲▼ to select [PROJECTOR ID].
1  ) 
Press the  button.
2  ) 
The [PROJECTOR ID] screen appears. 
z
Press ▲▼ to select [PROJECTOR ID].
3  ) 
Select [ALL] or a number between [1] and [6]  
z
from the list that appears.
ALL1
6 2
Press the  button to confirm 
4  ) 
the entry.
The selected [PROJECTOR ID] appears. 
z
Note
If the projectors are given ID numbers, their remote 
 
z
controls must be assigned the same ID numbers, 
respectively.
If the ID number of a projector is set to [ALL], it can be 
 
z
controlled by the remote control or the PC with any ID 
number.
If multiple projectors are used and some of them 
have their IDs set to [ALL], they cannot be controlled 
separately from the projectors with other ID numbers. 
For details on remote control ID setting, refer to “Setting 
Remote control ID numbers” (
Æpage 20).
INITIAL START UP
Use the steps below to select INITIAL START UP 
when the projector is connected to a wall outlet.
Press ▲▼ to select [INITIAL START 
1  ) 
UP].
Use ◄► to switch [INITIAL START UP] 
2  ) 
settings.
Each press of the button switches the settings  
z
as shown below.
LAST MEMORYSTANDBYON
LAST 
MEMORY Starts up the projector in the mode it 
was in when last shut down
STANDBY Starts up in standby mode
ON Starts projection immediately 
						

							PROJECTOR SETUP menu
ENGLISH - 57
Settings
PROJECTION METHOD
A projection scheme can be chosen depending on 
the installation of the projector. If the picture is shown 
upside down or in reverse, change the projection 
method.
Press ▲▼ to select [PROJECTION 
1  ) 
METHOD].
Press ◄► to switch [PROJECTION 
2  ) 
METHOD].
Each press of the button switches the settings  
z
as shown below.
FRONT/DESKFRONT/CEILING
REAR/CEILINGREAR/DESK
FRONT/DESK When mounted on a desk or stand 
in front of the screen
FRONT/
CEILING When mounted to the ceiling using 
ceiling mount brackets (optional 
accessory) in front of the screen.
REAR/DESK When mounted on a desk or stand 
behind the screen (when using a 
translucent screen)
REAR/ 
CEILING When mounted to the ceiling using 
ceiling mount brackets (optional 
accessory) behind the screen (when 
using a translucent screen)
HIGH ALTITUDE MODE
If you use the projector at elevations (1 400 m (4593 
ft) to 2 700 m (8858 ft)), the [HIGH ALTITUDE MODE] 
setting needs to be [ON].
Press ▲▼ to select [HIGH ALTITUDE 
1  ) 
MODE].
Press ◄► to switch [HIGH ALTITUDE 
2  ) 
MODE].
Each press of the button switches the settings  
z
as shown below.
OFFON
OFF Select this when using in normal 
environment (lower than 1 400 m 
(4593 ft) above sea level)
ON Select this when using at high 
altitude (1400 m (4593 ft) or higher 
and lower than 2700 m (8858 ft) 
above sea level)
Note
Make sure to set this to [OFF] when you use the 
 
z
projector at elevations lower than 1400 m (4593 ft) above 
sea level. Set this to [ON] when you use the projector 
at elevations of 1400 m (4593 ft) or higher and lower 
than 2700 m (8858 ft). Failure to observe this may result 
in shortening of the life of units or malfunction of the 
projector.
Do not install the projector at elevations of 2700 m (8858 
 
z
ft) or higher. Doing so may result in shortening of the life 
of units or malfunction of the projector.
The loudness of fan noise depends on the [HIGH 
 
z
ALTITUDE MODE] setting.
LAMP POWER
Can switch the electric power of projector lamp. Set 
the lamp power to meet the environment and purpose 
of projection.
Press ▲▼ to select [LAMP POWER].
1  ) 
Press ◄► to switch [LAMP POWER].
2  ) 
The setting will change as follows each time the  
z
button is pressed.
NORMALECO
NORMAL When high brightness is needed
ECO When high brightness is not needed
Note
The [ECO] mode can reduce power consumption and 
 
z
operation noise.
The selection made here is reflected to the indication of 
 
z
set ECO level in the “Multi Projector Monitoring & Control 
Software” installed from the supplied CD-ROM. 
						

							PROJECTOR SETUP menu
58 - ENGLISH
Settings
SCHEDULE
This sets the command execution schedule for each 
day of the week.
How to enable the SCHEDULE  
J
function
Press ▲▼ to select [SCHEDULE].
1  ) 
Press ◄► to switch [SCHEDULE].
2  ) 
Each press of the button switches the settings  
z
as shown below.
ONOFF
ON Enables set SCHEDULE
OFF Disable set SCHEDULE
Note
If [SCHEDULE] is set to [ON], the setting for [STANDBY 
 
z
MODE] is automatically set to [NORMAL] and cannot be 
changed. Even if [SCHEDULE] is then set to [OFF] when 
in this state, the setting of [STANDBY MODE] remains at 
[NORMAL].
How to assign a program 
J
With [SCHEDULE] switched to [ON], 
1  ) 
press  button.
The [SCHEDULE] screen will be displayed. 
z
Select and assign program to each day 
2  ) 
of week.
Press ▲▼ to select a day of week and press  
z
◄► to select a program number.
You can set the program from No.1 to No.7. 
 
z
“- - -” indicates that the program number has 
not been set yet.
How to set a program 
J
You can set up to 16 commands to each program.
On the [SCHEDULE] screen, press ▲▼ 
1  ) 
to select [PROGRAM EDIT].
Press ◄► to select a program number 
2  ) 
to be set (Program 1 to Program 7) and 
press the  button.
Press ▲▼ to select a command 
3  ) 
number (01 to 16) and press the 
 button.
You can change the page using ▲▼. 
z
Press ▲▼ to select [TIME] or 
4  ) 
[COMMAND] and change the setting 
according to the instructions of the 
menu.
Press the  button after selecting the  
z
[COMMAND], and you can set detailed settings.
TIME Set the time at which the command 
will be executed using ▲▼ buttons.
COMMAND Select a command to execute at the 
set time from the following.
POWER ON
• 
STANDBY• 
AV MUTE ON• 
AV MUTE OFF• 
INPUT • 
COMPUTER
INPUT VIDEO
• 
INPUT S-VIDEO• 
INPUT DVI-I• 
INPUT HDMI• 
INPUT • 
NETWORK
LAMP POWER 
• 
NORMAL
LAMP POWER 
• 
ECO SIDE BY SIDE 
• 
MODE OFF*1
SIDE BY SIDE • 
MODE ON*1
IN STANDBY • 
MODE (AUDIO) 
ON
IN STANDBY 
• 
MODE (AUDIO) 
OFF
VOLUME
• 
PT-FW430U only
*1 : 
Press ▲▼ to select [STORE] and 
5  ) 
press the  button.
Note
If you try to register a setting that would cause the lamp to  
z
flash for a short time, an error message will be displayed on 
the screen. Set the [TIME] and [COMMAND] again.
If multiple commands have been set for the same time, 
 
z
they are executed in chronological order starting from the 
smallest command number.
The setting time operates under the local time.   
 
z
(
Æpage 62)
If an operation is executed with the remote control or 
 
z
control panel of the projector or with a control command 
before the command set in the schedule is executed, the 
command set with this function may not be executed. 
						

							PROJECTOR SETUP menu
ENGLISH - 59
Settings
ECO MANAGEMENT
Can optimize lamp power and reduce the power 
consumption according to the application.
Press ▲▼ to select [ECO 
1  ) 
MANAGEMENT].
Press the  button.
2  ) 
The [ECO MANAGEMENT] screen is displayed. 
z
Press ▲▼ to select the item and press 
3  ) 
◄► to switch the setting.
 
JAUTO POWER SAVE
[AMBIENT LIGHT DETECTION], 
[SIGNAL
 DETECTION], and [AV MUTE DETECTION] 
functions can be used.
Note
Not available when [LAMP POWER] is set to [ECO].
 
z
Select [AUTO POWER SAVE] in Step 3.
1. 
Press ◄► to switch ON (Enable) / OFF 
2. 
(Disable) of the [AUTO POWER SAVE] 
setting.
The setting will change as follows each time the  
z
button is pressed.
ONOFF
ON Enables AUTO POWER SAVE
OFF Disables AUTO POWER SAVE
Press ▲▼ to select [AUTO POWER 
3. 
SAVE] conditions.
AMBIENT LIGHT 
DETECTION Adjusts the lamp power according 
to the ambient brightness.
SIGNAL 
DETECTION Drops the lamp power when no 
signal is input.
AV MUTE 
DETECTION Drops the lamp power in the AV 
Mute mode.
Press ◄►to switch ON (Enable) / OFF 
4. 
(Disable) of the selected condition.
The setting will change as follows each time the  
z
button is pressed
ONOFF
ON Enables the setting
OFF Disables the setting
Note
In following cases, [LAMP POWER] does not drop 
 
z
automatically.
When [LAMP POWER] is [ECO].
• 
Immediately after the lamp is turned on or immediately • 
after setting [LAMP POWER]
When [ECO MANAGEMENT] is [OFF], you cannot set 
 
z
[AMBIENT LIGHT DETECTION], [SIGNAL DETECTION], 
and [AV MUTE DETECTION] linked.
The selection made here is reflected to the indication of 
 
z
set ECO level in the “Multi Projector Monitoring & Control 
Software” installed from the supplied CD-ROM.
 
JNO SIGNAL SHUT-OFF
If no signal is input within a preset time, the projector 
power is automatically switched to the standby state.
DISABLE15 MIN60 MIN
DISABLE Disables NO SIGNAL SHUT-
OFF
15 MIN. -  60 MIN. Allows you to set a time in 5 
minute increments after which 
the projector will automatically 
shut down if there is no signal
Note
The selection made here is reflected to the indication of 
 
z
set ECO level in the “Multi Projector Monitoring & Control 
Software” installed from the supplied CD-ROM.
The duration is set to 30 minutes under factory default 
 
z
settings and after you perform [INITIALIZE ALL].
 
JSTANDBY MODE
This function can set the electric power when the 
projector is standing by.
NORMALECO
NORMAL Does not restrict functionality even in 
standby mode
ECO  Restricts some functions in standby 
mode to reduce power consumption
Note
If STANDBY MODE is set to [ECO], you cannot use 
 
z
network functions when the projector is standing by. Also, 
you cannot use some RS-232C protocol commands. 
When you turn the POWER switch [ON], display of 
the initial image may be delayed for approximately 
10 seconds when compared with [NORMAL] mode 
operation.
If set to [NORMAL], you can use network functions when 
 
z
the projector is standing by. 
						

							PROJECTOR SETUP menu
60 - ENGLISH
Settings
EMULATE
When using the control commands for one of our 
projectors that you have previously purchased to 
control this projector using a computer via its serial 
input terminal, set up the EMULATE function as 
follows. This will allow you to use the control software 
etc. designed for our existing projectors.
Press ▲▼ to select [EMULATE].
1  ) 
Press the  button.
2  ) 
The [EMULATE] screen appears. 
z
Press ▲▼ to select the required item.
3  ) 
Press the  button.
4  ) 
Note
Refer to “Serial terminal” (
 
zÆpage 77).
DEFAULT FX400 Series, FW430 Series, 
F100 Series, FW100 Series, 
F200 Series, F300 Series, 
FW300 Series
D3500 D3500 Series
D4000 D4000 Series
D/W5k D5500 Series, 
DW5000 Series, D5600 Series, 
DW5100 Series, D5700 Series
D/W/Z6k D5000 Series, D6000 Series, 
DW6300 Series, 
DZ6700 Series, 
DZ6710 Series, 
DZ570 Series,
DW530 Series,
DX500 Series
L730  L520 Series, 
L720 Series, L730 Series
L780 L750 Series, L780 Series
L735 L735 Series
L785 L785 Series
LB/W LB2 Series, LB1 Series, 
LB75 Series, LB80 Series, 
LB90 Series, ST10 Series, 
LB3 Series, LW80NT Series
FUNCTION BUTTON
Three function buttons ( to ) on 
the remote control can be assigned to any frequent 
operations. They can be used as a useful shortcut 
button.
To assign functions to the  
J
 to  buttons
Press  button on the remote 
1  ) 
control or the projector to select a 
menu option (Main Menu, Sub-menu or 
Advanced Menu).
For the on-screen menu selection, see  
z
“Navigating through the menu". (Æpage 35)
Hold down any of the  to 
2  ) 
 buttons on the remote 
control more than 3 seconds.
To cancel functions assigned  
J
to the  to  
buttons
Press ▲▼ to select [FUNCTION].
1  ) 
Press the  button.
2  ) 
Press ▲▼ to select [CANCEL] for 
3  ) 
the function button ( to 
) assigned with the function.
Press the  button.
4  ) 
When the confirmation screen appears, 
5  ) 
press ◄► to select [OK], then press 
the  button.
Note
When the setting is complete, the following indicators 
 
z
will apprear to the left of the assigned menu item (Main 
menu, Sub-menu, or Advanced menu): F1 for , 
F2 for , and F3 for .