Panasonic LCD Projector PT-EX16KE PT-EX16KU Operating Instructions

About your projector
ENGLISH - 21
Preparation
■
■ Control panel
(1)
(2)
(3)
(4)
(5)
(6)
(7) (8)
(9)
(10)
(11)
(6)
(12)
(1) Power  button
Turns off/on the power when the main power switch on the 
projector is set to 
.
(2)  button Opens and closes the shutter. Adjusts the shielding of the 
projection light. (
 page 37)
(3)  button Adjusts the zoom of the lens. (
 page 36)
(4)  button Adjusts focus. (
 page 36)
(5)  button Displays the menu screen. (
 page 40)
(6) ▲▼◀▶  buttons
Move the cursor on the...

About your projector
22 - ENGLISH
Preparation
■
■ Connection terminals
(1) (2) (3) (4) (10) (9) (8) (7) (6)
(5)
(1) DVI-D input terminal 
This terminal is for inputting the DVI-D signal.
(2) HDMI input terminal  This terminal is for inputting the HDMI signal.
(3) Computer input terminal  This terminal is for inputting an RGB signal.
(4) RGB 5BNC input terminal //
This terminal is for inputting the G,B,R,H/HV,V signal, 
video signal, and Y,Pb/Cb,Pr/Cr signal.
(5) USB terminal  This terminal is for use by...

Using the remote control 
ENGLISH - 23
Preparation
Using the remote control 
Inserting and removing the batteries
1) Open the cover.
(ii)(i)
2) Insert the batteries and close the 
cover
.
■zInsert the  side first.
■zTo remove the batteries, follow the above 
procedure in reverse.
Setting remote control numbers
When you are using multiple projectors, you can set a remote control number to each projector to allow 
simultaneous control with a single remote control.
After setting a remote control number of a...

Setting up
24 - ENGLISH
Getting Started
Setting up
Attaching the lens
Before putting the projector in position, attach the lens to the projector body.
First, determine the correct lens for the environment in which you are going to use the projector .
For lens product numbers and lens specifications suitable for the projector , consult your dealer. When attaching 
or replacing a lens, consult the technical staff or service personnel at a specialist dealer for safety. Do not attempt 
to attach or replace...

Setting up
ENGLISH - 25
Getting Started
Installation options (optional)
You can install the projector on the ceiling using the optional ceiling mount bracket (Product No.: ET-PKE16H (for 
high ceilings), ET-PKE16S (for low ceilings) and ET-PKE16B (for projector)).
 zUse only ceiling mount brackets specified for this projector

.
 zFor details on installation of the projector with the bracket, refer to the installation manual for the ceiling mount 
bracket.
Attention
 z T

o ensure the projector...

Connections
26 - ENGLISH
Getting Started
Connections
Before connecting to the projector
 zRead carefully the instruction manual of the device you intend to connect.
 zT

urn off the power switch of the device before connecting the cable.
 z If a connection cable is not supplied with the device and the optional cable is not available, prepare a 
connection cable to suit the device.
 zV

ideo signals containing too much jitter may cause the images on the screen to randomly wobble. In this case, 
a time...

Connections
ENGLISH - 27
Getting Started
Connecting example: AV equipment
Video, S-video, DV\MD player, and HDM\f vi\Mdeo 
output device\b
To HDM\f output
To AV HDCP 
DV\f video outputTo  
terminal
To  termina\Ml
To  termin\Mal To  terminal To  term\Minal
To compo\bite 
video output To component 
video output
To S-video output
DV\f-D cable
HDM\f cable BNC cable BNC cable
S-video cable
Attention
 z
Always use one of the following when connecting a VCR.
–

■
A
  VCR with built-in time base corrector (TBC)...

Connections
28 - ENGLISH
Getting Started
Tying up the cables using cable ties
Keep the cables tidy by fixing the cables connected to the terminals into the cable holders on the projector body.
 zThe cable ties can be reused. (The tab can be loosened and released.)
■
■ Loosening the cable ties
(i) (ii)Tab
Cable tie
Cable holders
1) Pull the tab in the direction of arrow (i).
2)  
Pull the tab in the direction of arrow (ii).
■z The loop of the cable tie will widen.
Attention
 z The following items are...

Installing an input module (optional) 
ENGLISH - 29
Getting Started
Installing an input module (optional) 
Installing an input module 
■
■ Types of input module
Purchase an input module (optional) matching the input signals of the system.
Module name SD/HD-SDI input module
Module number ET-MD16SD1  Input/output  terminal BNC 2 Input system, BNC 1 Output system
Compatible 
signal format SMPTE259M-C standard: 
480-60i (59.94
  Hz
*1), 576-50i (50 Hz)
SMPTE260M standard:  1035-60i (60/59.94
  Hz
*1)...

Installing an input module (optional) 
30 - ENGLISH
Getting Started
■
■ Using the input module
Consult your dealer before using any of the optional input modules.
When consulting your dealer, be sure to inform them of [Option control No.] of the projector.
[Option control No.] is displayed in the [Information] menu.
13Inform your dealer\s of this num\fer.
Language
\bnglish
16H
Ready
5Min
Off
180Min
OffAll
Code 08
Filter counter
Power management
Key lock
PIN code lock
Shutter management
Protection...