Panasonic LCD Projector PT-AH1000E Operating Instructions

							TEMP and LAMP Indicators
ENGLISH - 71
Maintenance
TEMP and LAMP Indicators
Managing the indicated problems
If a problem should occur with the projector, the lamp indicator  and/or temperature indicator  
will illuminate or flash. Check the indicator status and deal with problems as follows.Attention
When switching off power to deal with problems, ensure that you follow the procedure in “Switching off the power”. 
 
z
(
 page 29)
Note
Check the status of the power supply with the power indicator . (
 
z page 27)
 Lamp indicator
Temperature indicator
 
■ Temperature indicator 
Indicator 
status
Illuminates red during projection.   
 
z
(Alert indicating [REFER TO THE “TEMP indicator” SECTION IN THE OPERATION MANUAL.] is 
displayed.)  
Flashing red when power is turned off (projection stops automatically).
 
z
Problem The temperature inside and/or outside the projector is abnormally high.
Cause The air intake and 
exhaust ports may 
be obstructed. The room 
temperature may 
be too high.The air filter unit 
may be excessively 
dirty and ventilation 
may be poor.The projector may be being 
used at high elevations (1 400 
m or more above sea level).
Solution Remove object(s) 
from the ventilation 
ports or clear the 
area around the 
projector. Place the projector 
in an environment 
with temperature 
and humidity as 
designated in the 
specifications.
 
(
 page 90) Clean or replace 
the air filter unit.  
(
 page 73)The projector can only be 
used for two minutes after 
turning on.  Set [HIGH 
ALTITUDE MODE] to [ON] 
within two minutes of turning 
the projector on.
 
(
 page 66)
Note
If the  indicator is illuminated or flashes despite taking the actions above, please contact your dealer to have your 
 
z
projector repaired. 
						

							TEMP and LAMP Indicators 
72 - ENGLISH
Maintenance
 
■ Lamp indicator 
Indicator 
status Illuminated red
Flashing red
Problem
Time to replace the lamp unit. Illuminates when 
the lamp unit has reached its maximum usage 
period of 1 800 hours (when [LAMP POWER] 
is set to [NORMAL]). 
Lamp circuit failure, abnormal function or lamp unit 
is damaged.
Cause A message suggesting lamp replacement 
is displayed when power is turned on. The power may 
have been turned on 
immediately after being 
turned off.Lamp circuit failure, 
abnormal function or 
lamp unit is damaged.
Solution Replace the lamp unit. (
 page 77)Let the lamp unit cool 
down and turn on the 
power. Press the  side 
of the  
switch to turn off the 
power as described 
in the “Switching off 
the power” procedure 
(
 page 29), and 
contact your dealer.
Note
If the  indicator is illuminated or flashes despite taking the actions above, please contact an  Authorized Service 
 
z
Center to have your projector repaired. 
						

							Care and replacement
ENGLISH - 73
Maintenance
Before cleaning the projector / 
replacing components
Attention
Turn off the  switch and disconnect 
 
z
the power plug from the wall outlet before cleaning the 
projector/replacing components.
Follow the “Switching off the power” procedure when 
 
z
turning off the projector. (
 page 29)
Cleaning the projector
 
■ Cleaning the outer surface of the 
projector
Wipe off dirt and dust gently with a soft dry cloth.
If it is difficult to remove the dirt, soak a cloth in water, 
 
z
wring the cloth well and then wipe the projector. Dry 
the projector with a dry cloth.
Do not use petroleum benzene, thinner, any 
 
z
alcoholic solvent, or kitchen detergents. Using these 
substances may result in changes or damage to the 
surface of the projector.
When using a chemically treated cloth, follow the 
 
z
accompanying guidelines.
 
■ Cleaning the lens surface
If dirt or dust accumulates on the surface of the lens, it will 
be enlarged and projected onto the screen.
 
Wipe dirt and dust from the front of the lens gently with a 
clean, soft, and dry cloth.
Do not use a fluffy rag, or a greasy, wet, or dirty 
 
z
cloth.
Do not rub the lens harshly as this may damage the 
 
z
surface.
Attention
The lens is made of glass. It may break or crack if struck 
 
z
with a hard object or rubbed harshly. Please be careful 
when handling the lamp.
 
■ Air filter unit
If too much dust accumulates in the air filter the internal 
temperature of the projector cannot be maintained at the 
normal level. A confirmation message is displayed on the 
screen, and at the same time  illuminates red. The 
power is cut off automatically after a while. Clean the filter 
after every 100 hours of usage.
Remove the air filter cover.
1)  
Using a Phillips screwdriver to turn the fixing screw 
 
z
of the air filter cover until loose and remove the 
cover.
Air filter cover
Air filter cover fixing 
screw
Remove the air filter unit.
2)  
Hold the grips on the air filter unit, and remove it 
 
z
from the projector.
Air filter unit
Grips (
UP
 arrow engraved)
*  
After removing the air filter unit, remove any large build 
ups of dirt or dust in the air filter unit bay and the air 
intake port on the projector.
Vacuum dirt and dust from the air filter 
3)  
unit.
Do not wash the air filter unit.
 
z
Care and replacement 
						

							Care and replacement 
74 - ENGLISH
Maintenance
Attach the air filter unit to the projector.
4)  
  Attach the air filter unit to the projector using the 
 
z
reverse of the procedure in 2).
*   Insert the air filter unit into the projector in the 
direction of the arrow engraved into the air filter 
frame (
UP) until it clicks into place.
Attach the air filter cover, and firmly 
5)  
tighten the air filter cover fixing screw 
(one) with a Philips screwdriver.
Attention
The air filter unit must always be installed in the projector. 
 
z
Failure to do so will result in malfunctions due to foreign 
materials, such as dust, entering the projector.
Do not use water to wash the air filter unit as this 
 
z
decreases its ability to absorb dust. 
						

							Care and replacement
ENGLISH - 75
Maintenance
Component replacement
 
■ Air filter and 
electrostatic filter
The air filter should be replaced when cleaning is ineffective.   
A replacement air filter / electrostatic filter is available separately (service component).    
Contact your dealer for the optional air filter and electrostatic filter . 
 Also, please replace the air filter and electrostatic filter when replacing the lamp unit.   
 (An air filter and electrostatic filter are included with the [ET -LAA110] replacement lamp unit.)
 
■ Lamp unit
The lamp unit is a consumable component. See “When to replace the lamp unit” ( page 76) about the lifespan.
Contact your dealer if you wish to purchase a replacement lamp unit (ET -LAA110: Service component).
It is recommended that specialized engineers perform lamp unit replacement. Contact your dealer .
Attention
Wait until the lamp unit has cooled sufficiently before replacing (wait one hour or longer). 
 
z
The lamp cover gets very hot, and contact with it can cause burns.
 
Before replacing the lamp unit
 
■
A Phillips screwdriver is necessary when carrying out  
z
replacement. Hold the screwdriver firmly.
The light source lamp is a glass component. If it is hit on a hard 
 
z
object or dropped, breakage may occur. 
Be careful when handling a light source lamp.
Do not disassemble or modify the lamp unit.
 
z
Grip the handle when you remove the lamp unit. Some parts of  
z
the lamp unit are sharpened and may cause injury.
The lamp may be ruptured. Care should be taken not to scatter 
 
z
pieces of the broken lamp glass when replacing the lamp unit. 
Pieces of the broken lamp may fall from the lamp unit especially 
when the projector is mounted on the ceiling, so when replacing 
the lamp unit do not stand directly underneath it or position your 
face close to it. 
The lamp contains mercury. Contact the local government office 
 
z
or distributor for the correct disposal of the old lamp unit.
Note
Be sure to use the lamp unit specified.
 
z 
						

							Care and replacement 
76 - ENGLISH
Maintenance
 
■ When to replace the lamp unit
The lamp unit is a consumable component. Brightness decreases according to duration of usage, so periodical replacement 
of the lamp unit is necessary. A rough estimate for the usage period is 2 000 hours, but depending on the characteristics of 
individual lamps, usage conditions, periods of continuous use, and environmental conditions etc., the lamp may cease to 
illuminate prior to reaching 2 000 hours of use. It is recommended that you prepare a spare lamp unit in advance.
 
As the risk of the lamp to cracking increases after 2 000 hours the lamp automatically turns of f.
On screen
REPLACE LAMP
Lamp indicator
Over 1 800*1 
hours The message is displayed for 30 seconds. 
If you press any button within the 30 
seconds, the message disappears.
Illuminates red, including when in standby 
mode.
Over 2 000
*1 
hours The message is displayed until you press 
any button.
*1: 
  This is the time value for when the lamp is used with [LAMP POWER] in the [OPTION] menu set to [NORMAL] ( page 66). 
Differs from the actual usage time displayed in [LAMP RUNTIME] of the [OPTION] menu. This time increases greatly when 
[LAMP POWER] is set to [ECO]. 
Note
Setting [LAMP POWER] to [ECO] results in decreased brightness but the lamp may be used for longer.
 
z
The usage period of 2 000 hours is a rough estimate and is not guaranteed.
 
z 
						

							Care and replacement
ENGLISH - 77
Maintenance
 
■ Lamp unit replacement procedure
Attention
Once a lamp unit has exceeded its lifespan of 2 000 
 
z
hours (when [LAMP POWER] is set to [NORMAL]) the 
projector can only be used for 10 minutes after turning 
on. (
 page 76)  
Perform steps 20) to 23) of the procedure within 10 
minutes.
If the projector is installed on the ceiling, do not carry out 
 
z
any replacement procedure directly underneath the lamp 
unit and keep your face away from the unit.
Do not open the top cover except when replacing the 
 
z
lamp unit.
Do not switch the power on while the top cover is 
 
z
opened.
Always replace the air filter and electrostatic filter 
 
z
whenever replacing the lamp unit.
Install the lamp unit and the lamp cover securely.
 
z
Press the  side of the  switch to turn off the power as 
described in the “Switching off the power” 
procedure (
 page 29), remove the power 
plug from the power outlet, and then after an 
hour or more, check if the area surrounding 
the lamp unit has cooled down.
Remove the video cable connected to the 
2)  
connecting terminal.
Attention
If you open the top panel fully, it may come into contact 
 
z
with connectors such as the video cable which may result 
in breakage of the video cable. Before opening the top 
panel, be sure to remove the connected video cables, etc.
Hold the protrusions at the front corner 
3)  
of the top cover of the projector and 
push up to open.
*  When the projector is mounted on the ceiling, stand 
at the lens side of the projector when opening/
closing the top cover.
Top cover
Protrusion
Attention
Be careful not to open the top panel too far. For what 
 
z
to do if the top panel comes off, see ”Attaching the top 
cover” (
 page 79).
Use a Philips screwdriver to unscrew 
4)  
the lamp cover fixing screw (one) until 
it becomes loose, and then remove the 
lamp cover.
* Slowly remove the lamp cover from the projector.
Lamp cover Lamp 
cover fixing 
screw
Use a Phillips screwdriver to unscrew the 
5)  
lamp unit fixing screws (2 screws) until 
loose.
Hold the handle of the lamp unit and with 
6)  
the lamp unit 
lock held in the direction of 
the black arrow, carefully pull it out of the 
projector unit in a vertical motion.
0â
Lamp unit fixing 
screws
Handle Lamp unit lock
Replace the new lamp unit while making 
7)  
sure that the direction of insertion is 
correct. Press the top of the lamp unit 
downwards and make sure the unit is 
installed securely. Tighten the lamp unit 
fixing screws (2 screws) securely with a 
Phillips screwdriver.
Press down on the A part firmly when inserting the 
 
z
lamp unit.
Mount the lamp cover, and tighten the lamp 
8)  
cover fixing screw (one screw) securely with 
a Phillips screwdriver.
Close the top cover of the projector.
9)  
Close the top cover using the reverse of the 
 
z
procedure in 3), and press the center of the top 
cover.
Reconnect the video cable disconnected 
10)  
in 2) to the connecting terminal. 
						

							Care and replacement 
78 - ENGLISH
Maintenance
Remove the air filter cover.
1 1)  
Using a Phillips screwdriver to turn the fixing screw 
 
z
of the air filter cover until loose and remove the 
cover.
Air filter cover
Air filter cover fixing 
screw
Remove the air filter unit.
12)  
Hold the grips on the air filter unit, and remove it 
 
z
from the projector.
Air filter unit
Grips (
UP
 arrow engraved)
*  
After removing the air filter unit, remove any large 
build ups of dirt or dust in the air filter unit bay and 
the air intake port on the projector.
Press the protrusions of air filter unit 
13)  
removed from the projector in the 
direction of the black arrow and remove 
the air filter frame.
Replace the air filter/electrostatic filter.
14)  
Replace the air filter and electrostatic filter in the air 
 
z
filter unit with new ones.
*   Ensure you attach the electrostatic filter and air 
filter in the correct order.
Air filter caseAir filter (black)
Electrostatic filter 
(white)
Protrusions
Ribs Air filter frame
Catches
Assemble the air filter unit.
1 5)  
First insert the electrostatic filter (white) into the 
 
z
center of the case ensuring that its edges do not 
ride on top of the ribs, and then insert the air filter 
(black) so that its four corners are within the case 
before attaching the air filter frame.
*    Take care so that the air filter does not get caught 
between the air filter frame and the case.
*    Align the catches and protrusions on the air filter 
case and air filter frame when assembling the 
air filter unit. When attaching the air filter frame, 
ensure that the 4 catches are properly aligned with 
the protrusions on the air filter case and they have 
clicked into place.
Attach the air filter unit to the projector.
16)  
Attach the air filter unit to the projector using the 
 
z
reverse of the procedure in 12).
*   Insert the air filter unit into the projector in the 
direction of the arrow engraved into the air filter 
frame (
UP) until it clicks into place.
Attach the air filter cover, and firmly 
17)  
tighten the air filter cover fixing screw 
(one) with a Philips screwdriver.
Insert the power plug into a power outlet, 
18)  
and press the  side of the  switch to turn on the power.
Press the power <
19)  
/|> button on the 
projector or on the remote control to 
start video projection. 
						

							Care and replacement
ENGLISH - 79
Maintenance
Press the  button to display the 
20)  
menu screen and select [OPTION] with 
the ▲▼ buttons.
Press the  button and select 
21)  
[LAMP RUNTIME] with the ▲▼ buttons.
Hold the  button down for 3 
22)  
seconds.
The confirmation message is displayed.
 
z
LAMP  RUNTIME
LAMP RUNTIME RESET .
CANCELOK
Select [OK] with the ◄ ► buttons and 
23)  
then press the  button.
LAMP RUNTIME is reset to “0”, and the projector 
 
z
powers off. After a short while, the projector enters 
standby mode.
 
■ Attaching the top cover
Hold the top cover as shown in the 
diagram below, align the hinge with the 
support, and while pushing the arm in the 
direction of the arrow (towards the inner 
side of the projector), push it into the 
groove.
Support
Arm
Groove
Hinge 
						

							Troubleshooting 
80 - ENGLISH
Maintenance
Troubleshooting
Re-confirm these points. 
See the relevant page for details.
Problem CausePage
Power does not turn 
on.
The power cord may not be connected.
 
z
The  switch is turned .
 
z
The wall outlet may not be supplying electricity.
 
z
The circuit breakers may have tripped.
 
z
 indicator or  indicator is illuminated or flashes.
 
z
The lamp unit may not have been installed correctly.
 
z 27
28
—
—
71 
77
No picture appears.
The signal input source may not be connected to a terminal properly .
 
z
The input selection setting may not be correct.
 
z
The [BRIGHTNESS] adjustment setting may be at the minimum setting.
 
z
The external device connected to the projector may not be functioning correctly .
 
z
The [BLANK] function may be in use.
 
z
The lens cover may still be attached to the lens.
 
z 25
33
37
—
70
18
The picture is fuzzy.
The lens focus may not have been set correctly.
 
z
The projector may not be at the correct distance from the screen.
 
z
The lens may be dirty.
 
z
The projector may be over tilted.
 
z 30
21
18
21
The color is pale or 
grayish.[COLOUR] and [TINT] may not be adjusted correctly.
 
z
The device connected to the projector may not be adjusted correctly .
 
z 37
—
The remote control 
does not work.
The batteries may have run out.
 
z
The batteries may not have been inserted correctly.
 
z
The remote control signal receiver on the projector may be obstructed.
 
z
The remote control may be out of the range of operation.
 
z
Fluorescent lights may be interfering.
 
z —
17
17
17 —
The picture does not 
display correctly.[TV-SYSTEM] and [RGB/YC
 
zBCR, ] or [RGB/YPBPR] are not selected correctly.
There may be a problem with the VCR or other signal source.
 
z
A signal which is not compatible with the projector is being input.
 
z 52, 53
—
86
Picture from a 
computer  
does not appear.
The cable may be too long. (Cable must be less than 10 m in length.)
 
z
The external video output from a personal computer may not be correct.   
 
z
 (You may be able to change the external output settings by pressing the [Fn] + 
[F3] or [Fn] + [F10] keys simultaneously. The actual method varies depending on 
the type of computer; refer to the documentation provided with your computer for 
further details.)  —
—
Video from HDMI 
compatible device 
does not appear or it 
appears jumbled.The HDMI cable is not fully inserted.
 
z
Turn the power for the projector and the external device off and on.
 
z
A signal which is not compatible with the projector is being input.
 
z 26
27
86
*  If the projector still does not work correctly after checking the points above, contact your dealer.