Panasonic LCD Projector PT-AH1000E Operating Instructions

							Remote control operation
ENGLISH - 31
Basic Operation
 
You can operate the projector with the remote control 
within a range of 7 m (23').
Operating by pointing at the projector
 
z
Ensure the remote control transmitter is facing the remote 
control signal receiver on the front of the projector during 
use.
Facing to the screen
 
z
Ensure the remote control transmitter is facing the screen 
and press the required buttons to operate the projector. 
The signal will be reflected off the screen. The operating 
range may differ due to the screen material. This function 
may not be effective with a translucent screen.
Note
Do not let strong light shine onto the signal receiver. The 
 
z
remote control may malfunction under strong light such 
as fluorescent light.
If there are any obstacles between the remote control 
 
z
and the remote control signal receiver, the remote control 
may not operate correctly.
Illuminating button lights
You can illuminate the button lights on the remote 
control.
Press 
Press the  button again to extinguish the 
button lights.
Note
Button lights dim if no actions are carried out for 
 
z
approximately 5 seconds, and then extinguish if no 
actions are carried out for a further 5 seconds.
After the button lights have automatically extinguished, 
 
z
they automatically illuminate again if any button is 
pressed. 
(If the  button is pressed within 10 seconds 
of illuminating, the button lights extinguish and do 
not automatically illuminate even if another button is 
pressed.)
Selecting the picture mode
You can switch to your desired picture mode settings.
Press 
The settings change as follows each time the button 
is pressed.
[NORMAL][DYNAMIC][GAME][SPORTS]
[VIVID CINEMA][CINEMA1][REC709]
Note
You can also switch the picture mode settings using the 
 
z
on-screen menu.   
For details see [PICTURE MODE] in the [PICTURE] 
menu. (
 page 37)
Adjusting the picture
Switchable setting items from the [PICTURE] menu of 
the on-screen menu can be displayed in a list.
Press 
Press the button to switch between [PICTURE] menu 
and [ADVANCED MENU] menu. Press ▲ ▼ to select 
the required menu item and ◄ ► to adjust.
[PICTURE] menu items  
 
z
[PICTURE MODE], [CONTRAST], [BRIGHTNESS], 
[COLOUR], [TINT], [COLOUR TEMPERATURE], 
[SHARPNESS ] and [DYNAMIC IRIS]
[ADVANCED MENU] menu items   
 
z
[GAMMA HIGH], [GAMMA MID], [GAMMA LOW], 
[CONTRAST], [BRIGHTNESS], [NR], [MPEG NR],   
[MOTION EFFECT], [x.v.Colour], [DETAIL CLARITY], 
[CINEMA REALITY], [TV-SYSTEM], [RGB/YC
BCR] and 
[RGB/YP
BPR]
Note
For details regarding the adjustment method, see the 
 
z
[PICTURE] menu (
 page 37)  and the [ADVANCED 
MENU] menu (
 page 42).
Press the  or  button or wait for 7 
 
z
seconds without performing any operation to clear the 
adjustment screen.
Set the [ADJUSTMENT MODE] to [SIMPLE] for adjusting  
 
z
[GAMMA HIGH], [GAMMA MID], and [GAMMA LOW] 
(
 page 42).
The items for [SHARPNESS] that can be adjusted differ 
 
z
depending on the [ADJUSTMENT MODE].  
[SIMPLE]:  [SHARPNESS] 
[ADVANCED]:  [H-SHARPNESS] 
    [V-SHARPNESS]
Remote control operation 
						

							Remote control operation
32 - ENGLISH
Basic Operation
Loading a saved setting
Displays the [MEMORY LOAD] menu.
Press 
Attention
Setting can also be performed using the on-screen menu. 
 
z
For details, see [MEMORY LOAD] in the [PICTURE] 
menu. (
 page 54)
Displaying the  [VIERA LINK 
MENU] menu
You can control some functions of the external device 
with this projector remote control.
Press 
Note
See “Using VIERA Link” for details.  (
 
z page 82)
Displaying the waveform 
monitor
By displaying the input signal from a connected 
external device with a waveform, you can check if the 
video signal (luminance) level is set to a value within 
this projector’s recommended range, and can adjust it 
accordingly.
Press 
The settings change as follows each time the 
 button is pressed.
[FULL SCAN (Y)][FULL SCAN (R)]
[SINGLE LINE SCAN (B)] [FULL SCAN (G)]
[SINGLE LINE SCAN (G)] [FULL SCAN (B)]
[SINGLE LINE SCAN (R)][SINGLE LINE SCAN (Y)]
The waveform monitor disappears when the 
 button is pressed again.
Note
Setting can also be performed using the on-screen menu. 
 
z
For details, see [WAVEFORM MONITOR] in [PICTURE] 
menu. (
 page 39)
[FULL 
SCAN] Checks that the waveform for each of the 
Y
- (brightness), R- (red), G- (green), and 
B- (blue) values for the whole image is 
within the recommended range.
[SINGLE  LINE 
SCAN]
Checks that the waveform for each of the 
Y - (brightness), R- (red), G- (green), and 
B- (blue) values for an arbitrary number 
of lines from the top of the screen to the 
bottom is within the recommended range.
Enables more detailed confirmation than 
 
z
[FULL SCAN].
Line position can be changed with the ▲▼ 
 
z
buttons.
The display position of the [WAVEFORM 
 
z
MONITOR] changes depending on the line 
position.
Note
Signals lower than 0 % in the waveform monitor will be 
 
z
displayed as same as 0 % on the projected image.
[SINGLE LINE SCAN] can display horizontal lines in Y - 
 
z
(brightness), R- (red), G- (green), and B- (blue) from the 
top of the screen to the bottom more finely than [FULL 
SCAN], and each item can be adjusted in the same way 
as [FULL SCAN].
When selecting [FULL SCAN], the display position of the 
 
z
waveform can be set using the ▲▼
▲
▼ buttons.
So that the display of individual adjustment screen in 
 
z
[PICTURE] does not interfere with the waveform monitor, 
the positioning of this screen differs depending on the 
circumstances at the time.
The [AUTO ADJUST] is executed by pressing the 
 
z
 button while the waveform is displayed. 
(
 page 39)
While the waveform monitor is displayed, you cannot 
 
z
adjust the [COLOUR MANAGEMENT] settings.
Resetting to the default 
settings
You can reset most of the settings or adjustment 
values for submenus to factory default settings.
Press 
For details, see “Navigating through the menu - 
Returning adjusted values to default settings” of “Menu 
navigation”. (
 page 34) 
						

							Remote control operation
ENGLISH - 33
Basic Operation
Submenu
When the VIERA Link control is enabled, the function 
menus of external devices can be displayed.  
(
 page 82)
Furthermore, points for a gamma adjustment can be 
altered. (
 page 42)
Press 
Switching the input signal
The input for projection can be switched.
Press 
The settings change as follows each time the button 
is pressed.
[COMPONENT IN]
[COMPUTER IN] [S-VIDEO IN]
[HDMI 2 IN][VIDEO IN]
[HDMI 1 IN]
[COMPONENT 
IN]COMPONENT signals (YCBCR/
YP
BPR) from the device connected 
to COMPONENT IN.
[S-VIDEO IN]S-VIDEO signal from the device  
connected to S-VIDEO IN.
[VIDEO IN]VIDEO signal from the device  
connected to VIDEO IN.
[HDMI 1/2 IN]
HDMI signal from the device 
connected to  
HDMI IN 1/HDMI IN 2.
[COMPUTER IN]
RGB signal and   
COMPONENT signals (YC
BCR/
YP
BPR) from the device connected 
to COMPUTER IN.
When [INPUT GUIDE] on the [OPTION] menu is 
set to [DETAILED] (
 page  63), graphical guidance 
will be displayed on the upper right of the projected 
image, and the currently selected input terminal 
can be checked. (The selected input method will be 
highlighted in yellow.)  
Press the button several times or press ▲ ▼ ◄ ► to 
cycle through the input methods.   
It may take time for the video to change after 
switching input.
Attention
Input a signal noted in the “List of compatible signals”. 
 
z
(
 page 86)
Note
See “Connecting terminals” regarding input ports. 
 
z
(
 page 19)
If no operations are performed for approximately 3 
 
z
seconds, the input guidance display automatically 
disappears.
If a port that has no input is selected, the whole input port 
 
z
graphic flashes. This graphic is displayed until an input is 
present.
Using the  button
Functions used often can be allocated to the 
 button on the remote control and this 
can be used as a short cut button.
Press 
Allocating operations to the 
 
■
 button
Press the  button in the controls 
1)  
of the projector or on the remote control 
to display the menu items for allocation 
(main menu, submenu, or detailed menu).
For how to use the on-screen menu, see “Navigating 
 
z
through the menu”. (
 page 34)
Hold the  button on the 
2)  
remote control down for at least 3 
seconds.
After setup is complete the allocated menu items 
 
z
are displayed under the on-screen menu.
Note
While the menu is displayed, the projector does not 
 
z
operate even when the button is pressed.
Displaying the [ ECO 
MANAGEMENT] menu
The settings screen for ECO MANAGEMENT can be 
displayed. (
 page 67)
Press  
						

							Menu navigation
34 - ENGLISH
Settings
Menu navigation
Navigating through the menu
Operating procedure
 
■
Press 
Press the <
1)   MENU> button on the remote 
control or in the controls of the projector.
The main menu is displayed.
 
z
PICTURE MODE
CONTRAST
BRIGHTNESS
COLOUR
TINT
COLOUR T EMPERATURE
SHARPNESS
DYNAMIC IRIS
LIGHT  HARMONIZER
WA VEFORM MONIT OR
SPLIT  ADJAST
ADVA NCED MENU
PICTURE MEMOR YNORMAL
SIMPLE
ON
0
0
0
0
0
PICTURE
POSITION
LANGUAGE OPTION
Press the ▲▼ buttons to select main 
2)  
menu items.
Select the item to be adjusted from the 4 items 
 
z
[PICTURE], [POSITION], [LANGUAGE] and 
[OPTION]. The selected item is indicated with a 
yellow cursor, and the submenu is displayed on the 
right hand side.
H-POSITION
V-POSITION
ASPECT
WSS
OVER SCAN
KEYST ONE
SCREEN A REA MEMORY 16:9
ON
0
0
0
0
PICTURE
POSITION
LANGUAGE OPTION
Press the  button.
3)  
The submenu is displayed, and submenu items 
 
z
become selectable.
Press the ▲▼ buttons to select the 
4)  
submenu item you wish to alter, then 
press the 
▲
▼ to switch settings/adjust.
For items where the setting is switched or that have 
 
z
a bar scale, the menu screen disappears and only 
the selected item (individual adjustment screen) is 
displayed, as shown in the diagram below.
H-POSITION 0
For items that are only names, pressing the 
 
z
 button displays the next screen and 
advanced settings can be performed.
Note
Pressing the  or  button when the 
 
z
menu screen is displayed returns to the previous screen.
Depending on the signal input, some items may not be 
 
z
adjustable and some functions may not be usable.
Some items can be adjusted even if a signal is not input.
 
z
See page 
 
z 35 for the submenu items.
 
■ Returning adjusted values to default 
settings
Press the  button on the remote control 
to return the settings/adjustment values to default 
settings.
Press 
This function differs depending on the screen 
displayed.
When the submenu screen is displayed:  
 
●
 The submenu items displayed are returned to 
their default settings.
When individual adjustment screen is displayed:  
 
●
Only the item currently being adjusted is returned 
to its default settings.
H-POSITION 0
Note
All settings cannot be simultaneously returned to default 
 
z
settings.
Some items do not return to default settings even you 
 
z
press the  button. Please set those items 
individually.
The vertical bar above the bar scale on the individual 
 
z
adjustment screen indicates the default setting.  
The position of the vertical bar varies depending on the 
input signal.
 
0
Current setting Default setting 
						

							Menu navigation
ENGLISH - 35
Settings
Menu list
The on-screen menu is used for settings and 
adjustments on this projector. 
See “Navigating through the menu” for details of on-
screen menu operation. (
 page 34)
The submenu of the main menu is displayed, and 
setting/adjustment for each item can be performed.
[
 
■ PICTURE] 
S-VIDEO IN/VIDEO IN/COMPONENT (YC
 
●BCR/
YP
BPR) signal input/HDMI
Submenu items Default 
setting Page
[PICTURE MODE] [NORMAL]37
[CONTRAST] [0]37
[BRIGHTNESS] [0]37
[COLOUR] [0]37
[TINT] [0]37
[COLOUR 
TEMPERATURE] [0]
38
[SHARPNESS] [SIMPLE]38
[DYNAMIC IRIS] [ON]38
[LIGHT HARMONIZER] Š38
[WAVEFORM MONITOR] —39
[SPLIT ADJUST] —41
[ADVANCED MENU] —42
[PICTURE MEMORY] —53
SIGNAL MODE 
*154
*1: COMPONENT IN/HDMI IN only
COMPUTER (RGB) signal input
 
●
Submenu items Default 
setting Page
[PICTURE MODE] [NORMAL]37
[CONTRAST] [0]37
[BRIGHTNESS] [0]37
[COLOUR 
TEMPERATURE] [0]
38
[SHARPNESS] [SIMPLE]38
[DYNAMIC IRIS] [ON]38
[LIGHT HARMONIZER] Š38
[WAVEFORM MONITOR] —39
[SPLIT ADJUST] —41
[ADVANCED MENU] —42
[PICTURE MEMORY] —53
SIGNAL MODE 54
[
 
■ POSITION] 
S-VIDEO IN/VIDEO IN
 
●
Submenu items Default 
setting Page
[H-POSITION] [0]55
[V-POSITION] [0]55
[ASPECT] [AUTO]56
[WSS] 
*1[ON] 58
[OVER SCAN] [+7]58
[KEYSTONE] [0]58
[SCREEN AREA MEMORY] Š59
*1: PAL signal input only
COMPONENT IN/COMPUTER IN
 
●
Submenu items Default 
setting Page
[H-POSITION] [0]55
[V-POSITION] [0]55
[DOT CLOCK] 
*1[0] 55
[CLOCK PHASE] 
*2[0] 55
[ASPECT] [16:9]56
[WSS] 
*3[ON] 58
[OVER SCAN] 
*4[0] 58
[KEYSTONE] [0]58
[AUTO SETUP] 
*5— 58
[SCREEN AREA MEMORY] Š59
*1: COMPUTER IN only (exc. 480i, 576i, 480p, 576p)
*2: Exc. 480i/576i
*3: COMPONENT IN (576i, 576p) only
*4: COMPONENT IN and COMPUTER signal (movie 
based signals) input only
*5: COMPUTER IN (RGB) signals only (exc. movie  based signals)
HDMI IN
 
●
Submenu items Default 
setting Page
[H-POSITION] [0]55
[V-POSITION] [0]55
[ASPECT] [16:9]56
[OVER SCAN] [0]58
[KEYSTONE] [0]58
[SCREEN AREA MEMORY] Š59
Note
The default settings may be different depending on the 
 
z
picture menu. 
						

							Menu navigation
36 - ENGLISH
Settings
[
 
■ LANGUAGE] 
Language
[DEUTSCH]
[FRANÇAIS]
[ESPAÑOL]
[ITALIANO]
[PORTUGUÊS]
[SVENSKA]
[NORSK]
[DANSK]
[POLSKI]
[
]
[MAGYAR]
[РУССКИЙ]
[
]
[
]
[ENGLISH]
[ ¤ ]
[ ÔŠ  ]
[
 
■ OPTION] 
Submenu items Default 
setting Page
[ON-SCREEN DISPLAY] —63
[BACK COLOUR] [BLUE]63
[STARTUP LOGO] [ON]64
[AUTO SEARCH] [ON]64
[HDMI SIGNAL LEVEL] *1[NORMAL] 64
[FRAME RESPONSE] [NORMAL]64
[PROJECTION METHOD] [FRONT/
DESK] 64
[TRIGGER 1 SETTING] [OFF] 65
[TRIGGER 2 SETTING] [OFF]65
[HIGH ALTITUDE MODE] [OFF]66
[LAMP POWER] [NORMAL]66
[ECO MANAGEMENT] Š67
[FUNCTION BUTTON] —68
[VIERA LINK SETTINGS] —68
[OTHER FUNCTIONS] —70
[TEST PATTERN] —70
[LAMP RUNTIME] —70
*1: HDMI IN only
Note
Display of submenu items and default settings differs 
 
z
depending on the selected input port. 
						

							[PICTURE] menu
ENGLISH - 37
Settings
Select [PICTURE] from the main menu of 
“Navigating through the menu” (
 page 34), 
and choose an item from the submenu.
After selecting an item, adjust the image with the 
 
z▲
▼ 
buttons.
Remote contro lProjector controls
[PICTURE MODE]
You can use these preset parameter settings to 
optimize image projection according to image source 
or projection environment.
Switch settingsSwitch settings
The settings change as follows each time the button 
is pressed.
[NORMAL][DYNAMIC][GAME][SPORTS]
[VIVID CINEMA][CINEMA1][REC709]
[NORMAL]
For a general image.
[DYNAMIC] For viewing at high brightness and 
sharpness.
[GAME] For use with games.
[SPORTS] For sports program.
[REC709] For HDTV standard (ITU-R BT. 
709) color temperature 6 500 K at 
the default setting of the [PICTURE] 
menu items.
[CINEMA1] Tuned by top Hollywood colorists 
 
for watching a movie with smooth 
image quality.
[VIVID 
CINEMA] For use with a high luminance, 
clear picture mode.
Note
It may take a few seconds for the picture to stabilize after 
 
z
a picture mode change.
[CONTRAST]
You can adjust the contrast of the colors.
Lower
Higher
Setting range: -64 to +64
 
z
Attention
Adjust the [BRIGHTNESS] in advance if necessary.
 
z
[BRIGHTNESS]
You can adjust the dark (black) part of the projected
image.
Darker
Brighter
Setting range: −32 to +32
 
z
[COLOUR]
You can adjust the color saturation of the projected
image.
Lighter
Darker
Setting range: −32 to +32
 
z
Note
When COMPUTER signal is input, only movie based 
 
z
signals can be adjusted.
Movie based signals are 480i, 576i, 480p, 576p, 720/60p, 
 
z
720/50p, 1 080/60i, 1 080/50i, 1 080/60p, 1 080/50p and 
1 080/24p.
[TINT]
You can adjust the skin tone in the projected image.
Less greenish
Less reddish
Setting range: −32 to +32
 
z
Note
When COMPUTER signal is input, only movie based 
 
z
signals can be adjusted.
Movie based signals are 480i, 576i, 480p, 576p, 720/60p, 
 
z
720/50p, 1 080/60i, 1 080/50i, 1 080/60p, 1 080/50p and 
1 080/24p.
[PICTURE] menu 
						

							[PICTURE] menu
38 - ENGLISH
Settings
[COLOUR TEMPERATURE]
You can adjust the color temperature if the white 
areas of the projected image are bluish or reddish.Less bluish
Less reddish
Setting range: -6 to +6
 
z
[SHARPNESS]
With regards to the input signal, adjust video 
sharpness using one of [SIMPLE] which adjusts 
horizontal direction and vertical direction 
simultaneously or [ADVANCED] which adjusts each 
individually.
Softer
Sharper
Note
Setting range will vary according to the selected input 
 
z
signal.
[SHARPNESS] can be adjusted using either [SIMPLE] or 
 
z
[ADVANCED]. Both settings cannot be used at the same 
time.
Adjusting the [SHARPNESS].  
 
z
(When [SIMPLE] is selected for the 
[ADJUSTMENT MODE].)
Press 
1)  
▲
▼ buttons to select [SIMPLE].
 SHARPNESS
 A DJUSTMENT  MODE
 SHARPNESS
 H-SHARPNESS
 V -SHARPNESS SIMPLE
0
PICTURE
POSITION
LANGUAGE OPTION
Select [SHARPNESS] with the ▲▼ 
2)  
buttons, and adjust with the 
▲
▼ buttons.
Adjusting the [SHARPNESS].  
 
z
(When [ADVANCED] is selected for the 
[ADJUSTMENT MODE].)
Press the ◄► buttons to select 
1)  
[ADVANCED].
 SHARPNESS
 ADJUSTMENT  MODE
 SHARPNESS
 H-SHARPNESS
 V -SHARPNESS  A
DV ANCED
0
0
PICTURE
POSITION
LANGUAGE OPTION
Select item with the ▲▼ buttons, and 
2)  
adjust with the 
▲
▼ buttons.
Pressing the ▲▼ buttons on the screen during 
 
z
adjustment switches to the [H-SHARPNESS] or 
[V-SHARPNESS] adjustment screen.
 H-SHARPNESS
 V-SHARPNESS 0
0
The setting range varies according to the selected 
 
z
picture mode and input signal.
[DYNAMIC IRIS]
You can switch automatic adjustment of the lamp and 
the lens iris on/off. This augments the video to create 
a video expression with sharp contrast between light 
and shade.
Switch settingsSwitch settings
[ON] Automatic adjustment
[OFF] No adjustment
[LIGHT HARMONIZER]
You can optimize the video according to the 
brightness and color of the surroundings.
 LIGHT HARMONIZER
 MODE
 MANUAL  ADJUST MANUAL
PICTURE
POSITION
LANGUAGE OPTION
0
Switch settingsSwitch settings
[AUTO] Light harmonizer on (automatic 
augmentation). The color sensor 
detects the brightness of the 
surroundings and automatically 
augments the video display.
[MANUAL] Light harmonizer on (manual 
setting). When [MANUAL] is 
selected, [MANUAL ADJUST] can 
be set using the 
▲
▼ buttons 
(setting range: 0 to +3).
[OFF] Light harmonizer off.
Note
[AUTO] mode may not function correctly if an object is 
 
z
placed on the color sensor (
 page 18) or the projector 
is placed in a recess.  
						

							[PICTURE] menu
ENGLISH - 39
Settings
[WAVEFORM MONITOR]
By using a commercial test disk etc. and setting the 
luminance level of the output (brightness) signal from 
a connected external device to a value within this 
projector’s recommended range, you can perform 
adjustment so the display performance of the projector 
can be fully leveraged.
Press the  button.
1)  
The [WAVEFORM MONITOR] menu is displayed.
 
z
 W AV EFORM MONITO R
    OFF
    FULL  SCAN(Y)
    FULL  SCAN(R)
    FULL  SCAN(G)
    FULL  SCAN(B)
    SINGLE LINE SCAN(Y)
    SINGLE LINE SCAN(R)
    SINGLE LINE SCAN(G)
    SINGLE LINE SCAN(B)
 MONIT OR POSITION
 A UT O ADJUST UPPER LEFTÔ
Press the ▲▼ buttons to select the 
2)  
required item.
The waveform monitor is displayed.
 
z
Select [OFF] to close the waveform monitor.
 
z
Press the  button.
3)  
Note
For details, see “Displaying the waveform monitor” in 
 
z
“Remote control operation”. (
 page 32)
 
■ [MONITOR POSITION]
You can set the display position of the input waveform 
during the FULL SCAN display.
Switch settingsSwitch settings
[
 
■ AUTO ADJUST]
The luminance level of the output signal from a connected 
external device is automatically adjusted by setting the 
automatic waveform adjustment items.
Press the  button.
1)  
Press the ▲▼ buttons to select the 
2)  
required item.
Automatic waveform 
adjustment items Default 
setting
[BLACK LEVEL ADJUST] [ON]
[WHITE LEVEL ADJUST] [ON]
[RGB ADJUST (BLACK)] [OFF]
[RGB ADJUST (WHITE)] [OFF]
Press the ◄► buttons to switch 
3)  
adjustment.
Press the ▲▼ buttons to select [START 
4)  
AUTO ADJUST] and press the  
button.
[PROCESSING] message is displayed. When 
 
z
adjustment is complete, a confirmation message for 
applying results is displayed.
Select [OK] with the 
5)  ▲
▼ buttons.
Press the  button.
6)  
Note
When [BLACK LEVEL ADJUST] is [ON], the display 
 
z
signal Y (brightness) value’s black level is automatically 
adjusted to the 0% position.
When [WHITE LEVEL ADJUST] is [ON], the display 
 
z
signal Y (brightness) value’s white level is automatically 
adjusted to the 100% position.
When [RGB ADJUST (BLACK)] is [ON], the display signal 
 
z
R (Red), G (Green), and B (Blue) value’s black level are 
all automatically adjusted to the 0% position.
When [RGB ADJUST (WHITE)] is [ON], the display signal 
 
z
R (Red), G (Green), and B (Blue) value’s white level are 
all automatically adjusted to the 100% position.
[AUTO ADJUST] cannot be executed if the [WAVEFORM 
 
z
MONITOR] is [OFF].
Project the luminance adjustment signal of a commercial 
 
z
test disk etc., and perform automatic adjustment. 
However, even with an adjustment disk, correct 
adjustment may not be possible if noise is included on 
the disk itself or the playback device generates noise.
[AUTO ADJUST] adjusts based on the 0% and 100% 
 
z
standard signal within the screen, so correct adjustment 
cannot be performed if standard signals are not displayed 
on the screen because of overscan etc., or if a signal that 
is less than 0% or greater than 100% is displayed on the 
screen. 
						

							[PICTURE] menu
40 - ENGLISH
Settings
Adjust the waveform
 
■
Project the brightness adjustment signal of a commercial 
test disk (0% [0 IRE or 7.5 IRE] - 100% [100  IRE] ) and 
perform adjustment.
 
RETURN
MOVE DISPLA
Y
CHANGE WF MODE
Adjust to 100%
Signal (luminance) level
Signal (luminance) level
Monitor 
position
Monitor 
position Adjust to 100%
Adjust to 0 %
With COMPUTER (except 1 080 
signal) or HDMI (Expand)
Adjust to 0 % Image 
displayable 
area
Image 
displayable 
area
With the [WAVEFORM MONITOR] displayed, press the 
 button on the remote control and adjust using 
[ADVANCED MENU] and [PICTURE] from the on-screen 
menu.
Adjust [FULL SCAN(Y)] / [SINGLE LINE 
1)  
SCAN(Y)].
Set on [PICTURE] and use the 
 
z▲
▼ buttons to 
adjust [BRIGHTNESS] and then [CONTRAST].
[BRIGHTNESS]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
Setting range:  
 
z
−32 to +32
[CONTRAST]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
Setting range:  
 
z
−64 to +64
Adjust [FULL SCAN(R)] / [SINGLE LINE 
2)  
SCAN(R)].
Set on [ADVANCED MENU] and use the 
 
z▲
▼ 
buttons to adjust [BRIGHTNESS R] and then 
[CONTRAST R].
[BRIGHTNESS R]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
Setting range:  
 
z
−16 to +16
[CONTRAST R]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
Setting range:  
 
z
−32 to +32
Adjust [FULL SCAN(G)] / [SINGLE LINE 
3)  
SCAN(G)].
Set on [ADVANCED MENU] and use the 
 
z▲
▼ 
buttons to adjust [BRIGHTNESS G] and then 
[CONTRAST G].
[BRIGHTNESS G]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
Setting range:  
 
z
−16 to +16
[CONTRAST G]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
Setting range:  
 
z
−32 to +32