Panasonic LCD Projector PT-AE300U PT-AE200U Operating Instructions

40-E
NGLISH
ENGLISH
-41
Advanced Operation
4:3 H-POS(4:3 aspect mode only)
This sets the horizontal positioning
of the projected image when the 4:3
aspect ratio is selected. (Refer to
page 31.)FRONT/REARThis setting should be changed in
accordance with the projector
setting-up method.
Set to “FRONT” when using a
normal reflective screen with the
projector positioned in front of the
screen, and set to “REAR” when
using a translucent screen with the
projector positioned behind the
screen.DESK/CEILINGThis...

42-E
NGLISH
ENGLISH
-43
Advanced Operation
Inserting and removing the SD memory card
About the SD menuThe still image data and moving image data that is stored on SD memory
cards can be played back using the SD menu.Displaying the SD menuPress the SD button to change the display to the SD CARD screen.
Inserting the SD
memory cardInsert the SD memory card so that it
is facing the correct way.
#Open the slot cover at the side
of the projector.
$Insert the SD memory card as
shown in the illustration below....

44-E
NGLISH
ENGLISH
-45
Advanced Operation
Playing back still imagesThe PICTURE option lets you play back still image data.
Slide playback of still images“SLIDE SHOW” lets you play back still images in a certain order using one of
three available playback methods. Use the 
FandG
buttons to select an
item, and then press the ENTER button. Use the 
IandH
buttons to change
the setting for the selected item. #Use the Fand Gbuttons to
select “PICTURE”, and then
press the ENTER button.
BIf there is no still...

46-E
NGLISH
ENGLISH
-47
Advanced Operation
SETTING1
MANUAL MODE
NEW
USER SET AUTO MODE
SETTINGUSER SETIf adding settings for a new user, use the
Iand Hbuttons to select “NEW” and
then press the ENTER button. The user
setting edit screen will then be displayed.
If you would like to change the settings
for an existing user, use the Iand H
buttons to select the user setting file (0 -
9) that you would like to change, and
then press the ENTER button.User setting edit screen
(A) Still images set by user...

48-E
NGLISH
ENGLISH
-49
Advanced Operation
SETUPThis describes how to set the playback
interval and angle of rotation for still
images in the user settings.#Use the F, G, Iand H
buttons to select a still image
from the user settings, and
then press the ENTER button.
$Select “SETTING” and then
press the ENTER button.
“INTERVAL
”
Use the Iand Hbuttons to select
the time interval (seconds) between
playback of each still image.“ROTATE
”
Use the Iand Hbuttons to select the
angle of rotation for the still...

50-E
NGLISH
ENGLISH
-51
Advanced OperationOthers
IndicatorsThere are two indicators on the control panel of the projector which give
information about the operating condition of the projector. These indicators
illuminate or flash to warn you about problems that have occurred inside the
projector, so if you notice that one of the indicators is on, turn off the power
and check the table below for the cause of the problem.ProblemIndicator
display
Flashing (red)
(Lamp unit on)
The surrounding
temperature or...

52-E
NGLISH
ENGLISH
-53
Others
Cleaning and replacing the air filterIf the air filter becomes clogged with dust, the internal temperature of the
projector will rise, the TEMP indicator will flash and the projector power will
turn off. The air filter should be cleaned every 100 hours of use,
depending on the location where the projector is being used.Cleaning procedure#Turn off the MAIN POWER
switch and disconnect the
power cord plug from the wall
outlet.
Turn off the MAIN POWER switch
according to the...

54-E
NGLISH
ENGLISH
-55
Others
Lamp unit replacement procedureNOTE:
BIf the lamp usage time has passed 2000 hours (when LAMP POWER has
been set to “HIGH”), the projector will switch to standby mode after
approximately 10 minutes of operation. The steps *to -on the next
page should thus be completed within 10 minutes.
#Turn off the MAIN POWER
switch according to the
procedure given in “Turning off
the power” on page 23, and
then disconnect the power
cord plug from the wall outlet
and check that the area...

56-E
NGLISH
ENGLISH
-57
Others
Before calling for serviceBefore asking for service, check the following points.
Problem Possible cause
Power does not
turn on.
No picture appears.
The picture is
fuzzy.COLOR is too light or
TINT is poorNo sound can be
heard.BThe power cord may not be connected.
BThe MAIN POWER switch is turned off.
BThe main power supply is not being supplied to the
wall outlet.
BTEMP indicator is illuminated or flashing. (Refer to
page 51.)
BLAMP indicator is illuminated or flashing....

58-E
NGLISH
ENGLISH
-59
Others
SpecificationsPower supply: 100 V–240 V ~, 50 Hz/60 Hz
Power consumption: 180 W (During standby (when fan is
stopped): Approx. 1.5 W)
Amps: 2.2 A–1.0 A
LCD panel:
Panel size (diagonal): 0.7 type (17.78 mm)
Aspect ratio: 16:9
Display method: 3 transparent LCD panels (RGB)
Drive method: Active matrix method
Pixels:
PT-AE300U: 518 400 (960 x 540) x 3 panels
PT-AE200U: 415 272 (858 x 484) x 3 panels
Lens: Manual zoom (1 - 1.2) / focus lens 
F 2.0 - 2.3, f 22.0 mm - 26.2 mm...