Panasonic LCD Projector PT-AE100U Operating Instructions

							TQBJ 0095-1
LCD Projector 
Operating Instructions
Model No.
PT-AE100U
R
DIGITAL ZOOMENTERMENUNORMAL
FMUTEINPUTASPECTVOLUMEPROJECTOR
R
Before operating this product, please read the instructions carefully and save this
manual for future use.For assistance, please call : 1-888-VIEW-PTV(843-9788)
or send e-mail to : [email protected]
or visit us at www.panasonic.com (U.S.A)
For assistance, please call : 787-750-4300
or visit us at www.panasonic.co.jp/global/ (Puerto Rico)
ENGLISH 
						

							23
Preparation
IMPORTANT SAFETY NOTICEWARNING: 
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Dear Panasonic Customer:This instruction booklet provides all the necessary operating information that
you might require. We hope it will help you to get the most performance out
of your new product, and that you will be pleased with your Panasonic LCD
projector.
The serial number of your product may be found on its back. You should
note it in the space provided below and retain this booklet in case service is
required.Model number:  PT-AE100USerial number:
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
CAUTION:This equipment is equipped with a
three-pin grounding-type power
plug. Do not remove the grounding
pin on the power plug. This plug will
only fit a grounding-type power
outlet. This is a safety feature. If you
are unable to insert the plug into the
outlet, contact an electrician. Do not
defeat the purpose of the grounding
plug.
WARNING:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
–  Reorient or relocate the receiving antenna.
–  Increase the separation between the equipment and receiver.
–  Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–  Consult the dealer or an experienced radio/TV technician for help.
CAUTION:Any unauthorized changes or modifications to this equipment
will void the users authority to operate.Do not remove
Power Supply:This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60
Hz AC, house current only.
CAUTION:The AC power cord which is supplied with the projector as an accessory can
only be used for power supplies  up to 125 V, 7 A. If you need to use higher
voltages or currents than this, you will need to obtain a separate 250 V
power cord. If you use the accessory cord in such situations, fire may result.
Declaration of Conformity
Model Number:  PT-AE100U
Trade Name:Panasonic
Responsible party:  Matsushita Electric Corporation of America.
Address:  One Panasonic Way Secaucus New Jersey 07094
Telephone number:  1-888-843-9788
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. 
						

							5
Preparation
Precautions with regard to safetyWARNINGIf a problem occurs (such as no image or no sound) or if you notice
smoke or a strange smell coming from the projector, turn off the power
and disconnect the power cord from the wall outlet.
BDo not continue to use the projector in such cases, otherwise fire or
electric shocks could result.
BCheck that no more smoke is coming out, and then contact an Authorized
Service Center for repairs.
BDo not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place which is not strong enough to
take the full weight of the projector.
BIf the installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result.
Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.
BIf installation is not carried out correctly, there is the danger that injury or
electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, turn off the power and disconnect the
power cord from the wall outlet.
BContinued use of the projector in this condition may result in fire or electric
shocks.
BContact an Authorized Service Center for repairs.
Do not cover the air inlet or the air outlet.
BDoing so may cause the projector to overheat, which can cause fire or
damage to the projector.
Do not overload the wall outlet.
BIf the power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result.
Do not remove the cover or modify it in any way.
BHigh voltages which can cause fire or electric shocks are present inside
the projector.
BFor any inspection, adjustment and repair work, please contact an
Authorized Service Center.
Clean the power cord plug regularly to prevent it from becoming
covered in dust.
BIf dust builds up on the power cord plug, the resulting humidity can
damage the insulation, which could result in fire. Pull the power cord out
from the wall outlet and wipe it with a dry cloth.
BIf not using the projector for an extended period of time, pull the power
cord plug out from the wall outlet.
4ContentsPreparationIMPORTANT SAFETY NOTICE ..........2
Precautions with regard to safety ....5
Accessories ........................................9
Precautions on handling .................10
Location and function of 
each part........................................12
Using the remote control unit .........17
Inserting the battery ........................17
Operating range..............................17
Connections .....................................18
Notes on connections .....................18
Example of connecting to video
equipment ...................................18
Example of connecting to 
computer .....................................19
Example of connecting to equipments
compatible with YP
BPR(CBCR)
signals .........................................20
Setting-up .........................................21
Projection methods .........................21
Projector position ............................21
Basic OperationStarting to use ..................................22
Turning on the power......................22
Turning off the power......................23
On-screen menus.............................24
Menu screens .................................24
Menu operation guide .....................26
Unavailable on-screen 
menu items..................................26
Returning to the previous screen....26
Returning a setting to the factory
default .........................................27
Using the freeze function ................27
Using the DIGITAL ZOOM 
function .........................................28
Correcting keystone distortion.......29
Setting the ASPECT .........................30
Using the index window function ...32
Using the shutter function ..............33
Changing the display 
language ........................................33
Muting the sound .............................33
Adjusting the picture .......................34
PICTURE MODE ............................34COLOR ...........................................34
TINT................................................34
BRIGHT ..........................................34
CONTRAST ....................................35
SHARPNESS .................................35
TV SYSTEM ...................................35
Color Hue Setting  ..........................35
WHITE BALANCE R/G/B ...............35
SIGNAL MODE...............................35
Adjusting the position .....................36
HORIZONTAL POSITION ..............36
VERTICAL POSITION ....................36
DOT CLOCK...................................36
CLOCK PHASE ..............................36
ASPECT .........................................36
AUTO SETUP.................................37
Advanced OperationOption settings.................................37
OSD ................................................37
PC PRIORITY.................................37
BACK COLOR ................................37
4:3 H-POS ......................................37
FRONT/REAR ................................38
DESK/CEILING ..............................38
LAMP POWER ...............................38
LAMP TIME ....................................38
FUNCTION .....................................38OthersIndicators ..........................................39
Cleaning and replacing 
the air filter ....................................41
Replacing the lamp unit ..................42
Before asking for service ................45
Specifications...................................47
Appendix...........................................49
List of compatible signals ...............49
Connector pin wiring .......................50
Projection dimensions calculation
methods ......................................50
Dimensions.......................................51 
						

							7
Preparation
6
During a thunderstorm, do not touch the projector or the cable.
BElectric shocks can result.
Do not use the projector in a bath or shower.
BFire or electric shocks can result.
Do not look into the lens while the projector is being used.
BStrong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes.
Do not bring your hands or other objects close to the air outlet port.
BHeated air comes out of the air outlet port. Do not bring your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
When replacing the lamp, allow it to cool for at least one hour before
handling it.
BThe lamp cover gets very hot, and contact with it can cause burns.
Before replacing the lamp, be sure to unplug the power cord from the
power outlet.
BElectric shocks or explosions can result if this is not done.CautionDo not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.
BUsing the projector under such conditions may result in fire or electric
shocks.
When disconnecting the power cord, hold the plug, not the cord.
BIf the power cord itself is pulled, the cord will become damaged, and fire,
short-circuits or serious electric shocks may result.
Always disconnect all cables before moving the projector.
BMoving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur.
Do not place any heavy objects on top of the projector.
BFailure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
Do not short-circuit, heat or disassemble the battery or place it into
water or fire.
BFailure to observe this may cause the battery to overheat, leak, explode or
catch fire, and burns or other injury may result.
When inserting the battery, make sure the polarities (+ and -) are
correct.
BIf the battery is inserted incorrectly, it may explode or leak, and fire, injury
or contamination of the battery compartment and surrounding area may
result. Do not do anything that might damage the power cord or the power
cord plug.
BDo not damage the power cord, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
BIf the power cord is used while damaged, electric shocks, short-circuits or
fire may result.
BAsk an Authorized Service Center to carry out any repairs to the power
cord that might be necessary.
Do not handle the power cord plug with wet hands.
BFailure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
BIf the plug is not inserted correctly, electric shocks or overheating could
result.
BDo not use plugs which are damaged or wall outlets which are coming
loose from the wall.
Do not place the projector on top of surfaces which are unstable.
BIf the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result.
Do not place the projector into water or let it become wet.
BFailure to observe this may result in fire or electric shocks.
Do not place liquid containers on top of the projector.
BIf water spills onto the projector or gets inside it, fire or electric shocks
could result.
BIf any water gets inside the projector, contact an Authorized Service
Center.
Do not insert any foreign objects into the projector.
BDo not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric
shocks.
After removing the battery from the remote control unit, keep the
battery out of the reach of small children and infants.
BThe battery can cause death by suffocation if swallowed.
BIf the battery is swallowed, seek medical advice straight away.
Do not allow the + and - terminals of the battery to come into contact
with metallic objects such as necklaces or hairpins.
BFailure to observe this may cause the battery to leak, overheat, explode or
catch fire.
BStore the battery in a plastic bag and keep it away from metallic objects.
Please follow local codes and standards before disposing of batteries.
BContact recycling center for proper disposal of lithium batteries. 
						

							9
Preparation
8Use only the specified battery.
BIf an incorrect battery is used, it may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may
result.
Do not put your weight on this projector.
BYou could fall or the projector could break, and injury may result.
BBe especially careful not to let young children climb onto the projector.
Disconnect the power cord plug from the wall outlet as a safety
precaution before carrying out any cleaning.
BElectric shocks can result if this is not done.
Regular cleaning of internal parts and maintenance may be required
depending upon specific installation and location and/or usage.
BIf the projector is subjected to smoke, dust or humidity, please contact an
Authorized Service Center yearly to clean the projector.
We are in effort to hold your environment clean. Please bring the non
repairable unit your Dealer or a Recycling Company.Remote control unit
(N2QADC000003 x1)
Power cord
(K2CG3FR00001 x1) Video/Audio cable [3.0
m (9´10˝),
K2KA2FA00001 x1]Lithium battery for
remote control unit
(CR2025 x1)
AccessoriesCheck that all of the accessories shown below have been included with your
projector.
DIGITAL ZOOMENTER
MENU
NORMAL
F
MUTEINPUT
ASPECT
VOLUME
PROJECTOR
Carrying bag
(TPEP004-1 x1)
NOTICE:
BThis product has a High Intensity Discharge (HID) lamp that contains a
small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries
Alliance:  
						

							11
Preparation
10
About the screen
If the screen you are using is dirty, damaged or discolored, attractive
projections cannot be obtained. Do not apply any volatile substances to the
screen, and do not let it become dirty or damaged.Before carrying out cleaning and maintenance, be
sure to disconnect the power cord plug from the
wall outlet.Wipe the cabinet with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in water with a small amount
of neutral detergent in it, squeeze the cloth very well, and then wipe the
cabinet. After cleaning, wipe the cabinet dry with a dry cloth.
If using a chemically-treated cloth, read the instructions supplied with
the cloth before use.
Do not wipe the lens with a cloth that is dusty or which produces lint.
If any dust or lint gets onto the lens, such dust or lint will be magnified and
projected onto the screen. Use a blower to clean any dust and lint from the
lens surface, or use a soft cloth to wipe off any dust or lint.
Precautions on handlingCautions regarding transportationBe sure to attach the lens cover before transporting the projector.
The projection lens is extremely susceptible to vibration and shocks. When
carrying the projector, use the accessory carrying bag.
When placing the projector inside the carrying bag, position it so
that the lens is facing upward.Cautions regarding setting-upObserve the following at all times when setting up the projector.
Avoid setting up in places which are subject to vibration or shocks.
If the projector is set up in locations with strong vibration, such as near a
motor, or if it is installed inside a vehicle or on board a ship, the projector
may be subjected to vibration or shocks which can damage the internal parts
and cause malfunctions or accidents. Accordingly, set up the projector in a
place which is free from such vibrations and shocks.
Do not set up the projector near high-voltage power lines or near
motors.
The projector may be subject to electromagnetic interference if it is set up
near high-voltage power lines or motors.
If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.
If the projector is to be suspended from the ceiling, you will need to purchase
the separate installation kit (Model No.: ET-PKE100). Furthermore, all
installation work should only be carried out by a qualified technician.
If using of this projector at high elevations (above 1400 m), consult
your dealer or Authorized Service Center.
Special measures will be necessary to use this projector at high elevations,
so consult your dealer or Authorized Service Center about preparations.
Failure to observe this may cause malfunctions.Notes on useIn order to get the best picture quality
If outside light or light from indoor lamps is shining onto the screen, the
images projected will not have good contrast. Draw curtains or blinds over
any windows and turn off any fluorescent lights near the screen to prevent
reflection.
Do not touch the surfaces of the lens with your bare hands.
If the surface of the lens becomes dirty from fingerprints or anything else, this
will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it with the accessory lens cover. 
						

							13
Preparation
12
#Air outlet port
Do not cover this port.WARNINGDo not bring your hands or other
objects close to the air outlet
port.
BHeated air comes out of the air
outlet port. Do not bring your
hands or face, or objects which
cannot withstand heat close to
this port, otherwise burns or
damage could result.
$Connector panel 
(page 16)
%Power input socket (AC IN)
(page 22)
The accessory power cord is
connected here.
Do not use any power cord other
than the accessory power cord.
&MAIN POWER switch
(pages 22 and 23)'Lamp unit holder
(page 43)
NOTE:
BDuring projection of an image, the
cooling fan will operate, emitting
a small noise as it operates.
Turning the lamp on or off will
cause this noise to increase a
little.
BBy using the OPTION menu to
set “LAMP POWER” to LOW, the
operating sound of the fan can be
reduced. (Refer to page 38.)Projector 
Location and function of each part#Speaker
$Zoom ring
(page 23)
%Focus ring
(page 23)
&Projection lens
'Air inlet ports
Do not cover this port.
(Front adjustable legs(L/R)
(page 23)
)Lens cover
*Leg adjuster buttons(L/R)
(page 23)
This button is used to unlock the
front adjustable legs. Press to
adjust the angle of tilt of the
projector.
+Air filter
(page 41)
,Remote control signal receptor
(page 17)-Security lock
This can be used to connect a
commercially-available theft-
prevention cable (manufactured
by Kensington). This security lock
is compatible with the Microsaver
Security System from
Kensington. Contact details for
this company are given below.
Kensington Technology Group
ACCO Brands Inc.
2855 Campus Drive
San Mateo, CA 94403 USA
Tel (650)572-2700
Fax (650)572-9675
http://www.kensington.com/
http://www.gravis.com/
.Projector control panel
(page 14)Projector 
#
$
%
&
'
(
)
*-
+ , '
.
#
$
%
&
' 
						

							15
Preparation
14
+MENU button 
(page 24)
This button is used to display
menu screens. When a menu
screen is being displayed, it can
be used to return to a previous
screen or to clear the screen.
,NORM button 
(page 27)
This button is used to reset the
projector adjustment values to the
factory default settings.
-DIGITAL ZOOM +/- buttons 
(page 28)
These buttons are used to
enlarge certain portions of the
projected image.
.ENTER button 
(page 26)
This button is used to accept and
to activate items selected in the
on-screen menus.
/Arrow (F F
, G G
, I I
and H H
)
buttons
(page 26)
These buttons are used to select
and adjust items in the on-screen
menu screens.
0F(function) button 
(page 38)
This button momentarily freezes
a moving image (FREEZE menu
item), and it can be used to split
the screen into one frozen image
and one moving image (INDEX
menu item). Use the FUNCTION
item in the OPTION menu to
select which of these two
operations you want to use with
this button.1ASPECT button 
(page 30)
This button is used for aspect
adjustment (vertical and
horizontal proportions).
#TEMP indicator 
(page 39)
This indicator illuminates if an
abnormally high temperature is
detected inside the projector. If
the temperature rises above a
certain level, the power supply
will be turned off automatically
and the indicator will illuminate or
flash.
$LAMP indicator 
(page 40)
This indicator illuminates when it
is time to replace the lamp unit. It
flashes if a circuit abnormality is
detected.
%Power indicator
(pages 22 and 23)
This indicator illuminates red
when the main power is switched
on (Standby Mode), and it
illuminates green when projection
of an image begins.&POWER button
(pages 22 and 23)
'INPUT select button
(page 22)
(KEYSTONE buttons
(page 29)
These buttons are used to correct
keystone distortion of the
projected image when the
projector position is tilted upward
or downward.
)VOLUME +/- buttons
These buttons are used to adjust
the volume of the sound output
from the projector’s built-in
speaker.
*MUTE button
(page 33)
This button momentarily stops
output of the projector’s built-in
speaker.

STANDBY(R)
ON(G) LAMP TEMP
POWER
KEYSTONE VOLUME INPUT
DIGITAL ZOOMENTER
MENU
NORMAL
F
MUTEINPUT
ASPECTVOLUME
PROJECTOR
(
*+
''
&&
%
)
#
$
1
)
0
,
-.
/
BThe wireless remote control and the projector itself have the same control
buttons available. 
						

							17
Preparation
Inserting the batteryInsert the lithium battery which is
supplied with the remote control
unit, making sure that the polarities
are correct.
#While pushing the battery
holder tab to the right, pull out
the battery holder.
$Insert the battery into the
battery holder so that the “+”
side is facing upwards.
%Insert the battery holder.
NOTE:
BDo not drop the remote control
unit.
BKeep the remote control unit
away from liquids.
BRemove the battery if not using
the remote control unit for long
periods.
BUse only CR2025 batteries as
replacement batteries.Using the remote control unit
Operating rangeIf the remote control unit is held so
that it is facing directly in front of the
front remote control signal receptor,
the operating range is within
approximately 7 m (23´) from the
surfaces of the receptors.
Furthermore, the remote control unit
can be operated from an angle of
±30 °to the left or right and ±15 °
above or below the receptors.
NOTE:
BIf there are any obstacles in
between the remote control unit
and the receptors, the remote
control unit may not operate
correctly.
BIf strong light is allowed to shine
onto the remote control signal
receptor, correct remote control
operation may not be possible.
Place the projector as far away
from light sources as possible.
BIf facing the remote control unit
toward the screen to operate the
projector, the operating range of
the remote control unit will be
limited by the amount of light
reflection loss caused by the
characteristics of the screen
used.
Push the tab
Pull out
16
L
|
  AUDIO
|
RAUDIO
VIDEO INPC IN
VIDEO S2 VIDEOL
|
  AUDIO
|
RY
PB/CBPR/CR
COMPONENT IN
#
$
%
&
'
(
)
#AUDIO L-R input jacks (for
VIDEO/S-VIDEO)
(page 18)
Only one system is provided, so
connect the appropriate
connector when using VIDEO or
S-VIDEO.
$VIDEO input jack 
(page 18)
This jack is used to input video
signals from a video equipment
such as a video deck.
%S2 VIDEO input connector 
(pages 18 and 30)
This connector is used to input
signals from an S-VIDEO-
compatible equipment such as a
video deck. The connector is
compatible with S2 and S1
signals, and projector aspect is
automatically adjusted according
to the type of signal received.
&AUDIO input jack (for PC)
(page 19)
'RGB input connector
(page 19)
This connector is used to input
RGB signals from a PC.
(AUDIO L-R input jacks (for
YP
BPR)
(page 20))YP
BPR(C
BCR) input jacks
(page 20)
These jacks are used to input
YP
BPRsignals from compatible
equipment such as DVD players.
Match the “+”
surface of the
battery with the
“+” marked side of
the battery holder. 
						

							L
|
  AUDIO
|
RAUDIO
VIDEO INPC IN
VIDEO S2 VIDEOL
|
  AUDIO
|
R
COMPONEN
19
Preparation
18Example of connecting to video equipment
DVD player
Video deck
NOTE:
BOnly one audio system circuit is available for the AUDIO L-R input jacks
for S-VIDEO/VIDEO signals, so if you wish to change the audio input
source, you will need to remove and insert the appropriate plugs.
BIf the signal cables are disconnected or if the power supply for the
computer or video deck is turned off while the digital zoom or index
window functions are being used, these functions will be cancelled.NOTE:
BIt is better to shut down the computer before turning off the MAIN POWER
switch of the projector.
BRefer to the list of compatible signals on page 49 for the types of RGB
signals which can be input to the projector by connecting a computer.
Example of connecting to computer
ConnectionsNotes on connectionsBRead the instruction manual for each system component carefully before
connecting it.
BTurn off the power supply for all components before making any
connections.
BIf the cables necessary for connecting a component to the system are not
included with the component or available as an option, you may need to
fashion a cable to suit the component concerned.
L
|
  AUDIO
|
RAUDIO
VIDEO INPC IN
VIDEO S2 VIDEOL
|
  AUDIO
|
RY
PB/CBPR/CR
COMPONENT IN
Computer
To video output To audio 
output To audio
outputTo S-Video outputTo RGB output
To audio output
To audio
input
Audio
systemor