Panasonic Lcd Monitor Dvd Receiver Cq Vd7005u Operating Instructions

							40
41CQ-VD7005U
English
Note:
¡This adjustment is common to video mode.
¡
You cannot change the aspect in the menu screen and a
screen in the CD, MP3/WMA, radio and CD changer
mode. These are fixed to “FULL” as well as a Navigation
Image.
¡When the rear view camera is in operation with the
transmission gear shift in the reverse position, the
image is shown on the “FULL” screen only.
¡In some cases, the picture looks different from the
original one due to your selection of aspect.
Caution
¡This is to remind you that compression or extension
of the screen using the aspect ratio (screen mode)
changing function of this product for commercial
purpose of profit making or viewing/listening by the
public could infringe on the rights of the author pro-
tected by the copyright law.
¡If you expand normal picture (4 to 3) by using
“JUST”, “ZOOM” or “FULL” aspect to the full of the
screen, you might not see the periphery of the pic-
ture, or you might see a distorted picture.
Therefore, use the “NORMAL” mode to see the orig-
inal picture as the author intended it.
❑Private Mode
You can mute the sounds from the rear speakers if nec-
essary. Activation of the private mode allows you to enjoy
the front monitor and rear monitor (e.g. CY-VHD9401U)
independently with different sources at the same time.
Default: Private mode off
Press and hold [ASP]on the main unit for more than 2
seconds to activate the private mode function or inacti-
vate it in turn.
Note:
¡Be sure to set to OFF when you do not use the private
mode.
¡It is not possible to choose and set the  (CS
Auto Setting) (
apage 35) and 
(speaker delay) (
apage 37) on the sound setting
menu while private mode is active. 
TIME ALIGNMENT
CS Auto
“P • MODE” indicator
lights when the
Private Mode is acti-
vated.
It is recommended
to use optional
Over-head Monitor
(CY-VHD9401U)
and headphones
supplied to 
CY-VHD9401U.
Radio
DVD
Private modeOffPrivate modeOn
Mute
Radio
DVD
Radio 
						

							41
42CQ-VD7005U
English
Troubleshooting
■Common
❑If You Suspect Something Wrong
Check and take steps as described below.
If the described suggestions do not solve the problem, it is rec-
ommended to take the unit to your nearest authorized Panasonic
Servicenter. The product should be serviced only by qualified per-
sonnel. Please refer checking and repair to professionals.
Panasonic shall not be liable for any accidents arising out of neg-
lect of checking the unit or your own repair after your checking.
Never take measures especially those other than indicated by
italicletters in “Possible Solution” described below because
those are too dangerous for users to handle themselves.
Warning
¡Do not use the unit in an irregular condi-
tion, for example, without sound, or with
smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop
using the unit and consult your dealer.
¡Never try to repair the unit by yourself
because it is dangerous to do so.
ProblemPossible cause
aPossible solution
No power to the unit
The power cord (battery, power and ground) is connected in the wrong way.
aCheck the wiring.
Fuse blows out.
aEliminate the cause of fuse blowout and replace the fuse with new one.
Consult your dealer.
Sound is not 
generated.
MUTE is set to ON.
aSet MUTE to OFF.
The wiring of speaker lines is not correct, or a break or poor contact arises.
aCheck the wiring in accordance with the wiring diagram. (Installation
Instructions)
Noise
There is an electromagnetic-wave generator such as a cellular phone near the unit
or its electrical lines.
aKeep the electromagnetic-wave generator such as a cellular phone away
from the unit and the wiring of the unit. In case noise cannot be eliminated
due to the wiring harness of the car, consult your dealer.
The contact of the ground lead is poor.
aMake sure that the ground lead is connected to an unpainted part of the
chassis securely.
Noise is made in step
with engine revolutions.Alternator noise comes from the car.
aChange the wiring position of the ground lead.
aMount a noise filter.
Some operations are not
executable.Some operations are not executable in particular modes such as menu mode
aRead the operating instructions carefully and cancel the mode. If the unit is
still out of order, consult your dealer.
No sound from
speaker(s)There is a break, a short circuit, poor contact or wrong wiring regarding the
speaker wiring.
aCheck the speaker wiring. 
						

							42
43CQ-VD7005U
English
■Radio ■Common (continued)
■
CD
The speaker channels
are reversed between
right and left.The speaker wiring is reversed between right and left.
aPerform the speaker wiring in accordance with the wiring diagram.
The power of the unit
fails unintentionally.The safety device works.
aConsult your dealer, or your nearest Panasonic Servicenter.
Poor reception or noise
Antenna installation or wiring of antenna cable is faulty.
aCheck whether the antenna mounting position and its wiring are correct. In
addition, check to see whether the antenna ground is securely connected to
the chassis.
No power is supplied to the antenna amplifier (when using a film antenna, etc.).
aCheck the wiring of the antenna power lead.
The number of auto
preset stations is less
than 6.The number of receivable stations is less than 6.
aMove to an area where receivable stations number is maximum, and try pre-
setting.
Preset stations cannot
be stored.The contact of the battery lead is poor, or the battery lead is not always powered.
aMake sure that the battery lead is connected securely, and preset stations
again.
Sound skipping or noiseThere is a flaw or foreign object on the disc.
aRemove the foreign object, or use a flawless disc. 
No playback or disc
ejected
The disc is inserted upside down.
aInsert a disc correctly.
There is a flaw or foreign object on the disc.
aRemove the foreign object, or use a flawless disc.
Sound skipping due to
vibration 
The unit is not sufficiently secured.
aSecure the unit to the console box.
The unit is tilted at over 30˚ in the front-to-end direction.
aMake the angle 30˚ or less.
Disc unejectable
Something such as a peeled label obstructs the disc coming out.
aPress and hold the [u] for more than 10 seconds (disc forced ejection). In
case that the disc forced ejection does not work, consult your dealer.
The microcontroller in the unit operates abnormally due to noise or other factors.
aUnplug the power cord and plug it again. In case the unit is still out of order,
consult your dealer.  
						

							43
44CQ-VD7005U
English
Troubleshooting (continued)
No playback or disc
ejectedThe disc has unplayable formatted data.
aRefer to the description about MP3/WMA for playable sound data except CD-
DA (i.e. music CD).
The CD-R/RWs that are
playable on other
devices are not playable
on this unit.The playability of some CD-R/RWs may depend on the combination of media,
recording software and recorder to be used even if these CD-R/RWs are playable
on other devices such as a PC.
aMake CD-R/RWs in a different combination of media, recording software
and recorder after referring to the description about MP3/WMA.
Sound skipping or noise
There is a flaw or foreign objects on the disc.
aRemove the foreign objects, or use a flawless disc. For MP3/WMA, refer to
the description about MP3/WMA.
Playing VBR (Variable Bit Rate) files may cause sound skipping.
aPlay Non-VBR files.
■MP3/WMA
Cannot switch the audio
language/subtitle 
language/angle.¡It is not possible to switch if the disc does not have multiple audio
languages/subtitle languages/angles recorded on it. (Refer to the guide provid-
ed with your disc.)
¡Some discs permit switching through a menu screen.
¡Sometimes, switching angles is possible only with certain scenes.
The audio/subtitle 
language selected in the
DVD settings is not
used.If audio or subtitles in that language are not recorded on the disc, the audio or
subtitles do not switch to that language. (Some discs permit switching through a
menu screen. Refer to the guide provided with your disc.)
A DVD–R or DVD–RW is
not playable.
The disc is still unfinalized.
aFinalize the disc. 
Refer to “Before Disc Playback” (
apage 18) or “Notes on Discs” 
(apage 48) for other cases.
The disc is in the video recording (VR) format.
aPlay video formatted discs. 
Refer to “Before Disc Playback” (
apage 18) or “Notes on Discs” 
(apage 48) for other cases.
■
DVD
Note:
¡Refer to “Notes on MP3/WMA” (apage 24)
The brightness of the
screen is not stable.dimmer is selected.
aSelect one of the dimmer levels from among 1 to 4 to make the dimmer
adjustment become free from light intensity.AUTO
The picture is dark. The
picture is whitish. Something
is wrong with the picture.
The picture is light in color.
The screen is not adjusted properly.
aMake every adjustment of the screen.
The display does not go
back into the unit.The monitor stops on the way to the home position.aPress [OPEN] (CLOSE).
■
Display Settings 
						

							No sound from the
subwoofer
Playing back a disc having a subwoofer channel
¡Subwoofer is set to in the speaker setting.
aSet subwoofer to  .
¡Private mode is set to  .
aSet private mode to   .
¡Pro Logic is set to  .
aSet Pro Logic to  .
OFF
ON
OFF
ON
YES
NO
44
45CQ-VD7005U
English
No sound from left,
right, front, or rear
speaker.Cables are not correctly connected.
aConnect the cables correctly.
Left and right sounds are
reversed.The speaker leads are connected in reverse between right and left.
aConnect the speaker wires to the correct one.
No sound on the
speaker.The speaker setting is  or  .
aSet it correctly.NONENO
■
Sound Settings
No response to pressing
buttons
The battery is inserted in the wrong direction. A wrong battery is inserted.
aInsert a correct battery in the correct direction.
The battery is weak.
aReplace the battery with new one.
The aiming direction of the remote control unit is wrong.
aAim the remote control unit at the sensor of the unit and press buttons.
The sensor is exposed to direct sunlight. (The remote control unit may not be
operable when the sensor is exposed to direct sunlight. In such a case, the sys-
tem is not faulty.)
aBlock off sunlight to the sensor.
is selected for the remote control setting. 
aSelect   for the remote control setting.
FRONT
REAR
■
Remote Control Unit
Unable to turn on the
power of the main unit
through the remote
controlis selected for the ACC selection. 
aSelect   for the ACC selection.
aPress [SRC] (PWR) of the main unit to turn on the power.
ON
OFF 
						

							45
46CQ-VD7005U
English
Troubleshooting (continued)
❑
Error Display Messages
Note:
¡There may be cases when the disc numbers affected by an error are displayed before “NON PLAYABLE DISC”.
■CD/MP3/WMA/DVD/VCD (Video CD)
Display
Possible cause
aPossible solution
NON PLAYABLE DISC
Disc is dirty, or is upside down.
aCheck disc.
Disc has scratches.
aCheck disc.
MECHANISM ERROR
No operation by some cause.
aPress [u]. If failure persists, press the reset switch. If normal operation is not
restored, call the store where you purchased the unit or the nearest Panasonic
Servicenter.
FILE ERRORThe type of  the file that is selected is not supported.
aCheck disc.
PROTECTEDA WMA file can be copyrighted. 
aThe file protected by copyright is not playable.
NO DISCNo disc is in the player.
aInsert disc into the disc slot.
REGION ERRORAn attempt was made to play a disc with a region number other than “1” or “ALL”.
aPress [u] and check the disc.
❑In case you forget the ID code...
Model No. CQ-VD7005U
ID CODE
In case you forget the ID code, please consult your nearest Panasonic Servicenter.
ID code memo
Copy the memo below, fill in the ID code, and keep it in a secure location. 
						

							46
47CQ-VD7005U
English
❑Product Servicing
If the suggestions in the charts do not solve the problem,
we recommend that you take it to your nearest authorized
Panasonic Servicenter. The product should be serviced
only by a qualified technician.
❑Replacing the Fuse
Use fuses of the same specified rating (15 A). Using dif-
ferent substitutes or fuses with higher rating, or connect-
ing the product directly without a fuse, could cause fire or
damage to this unit.
If the replacement fuse fails, contact your nearest
Panasonic Servicenter for service.
❑If the Unit Begins to
Malfunction...
Reset switch
Insert a hard, slender stick into the hole and push the
switch.
Important
Push the switch only when the unit fails to operate with
any buttons. (Stored settings and adjustments are not
cleared.) 
If the unit fails to return to normal condition, call the near-
est Panasonic Servicenter and ask for repairs.
Note:
¡If the ID-CODE has been already set, you will be asked to
enter the ID-CODE right after the unit is restarted.
ENTER
TILTO/COPEN / CLOSE
TEXT
Reset switch
Maintenance
❑Cleaning this Unit
When the unit is dirty, wipe the surface of the display
using the Wiping Cloth (supplied).
Cleaning without the supplied cloth
1Moisten the soft cloth in dishwashing
soap diluted with water and wring well.
2Wipe lightly. Go over the same surface
with a dry cloth.
Note:
¡Since there is the possibility of water drops getting
inside of the unit, do not directly apply cleanser to the
surface.
¡Do not scratch the screen with your nails or other hard
objects. The resulting scratches or marks will obscure
the images.
❑Caution on Cleaning
Your product is designed and manufactured to ensure a
minimum of maintenance. Use a dry soft cloth for routine
exterior cleaning. Never use benzine, thinner or other sol-
vents.
Alcohol
Pesticide
Wax
Benzine Thinner
Caution
¡If water drops or similar wet substances get inside
the monitor, it may cause a malfunction.
Alcohol
Pesticide
Wax
Benzine Thinner 
						

							47
48CQ-VD7005U
English
Notes on Discs
How to hold the disc
¡Do not touch the underside of the disc.
¡Do not scratch the disc.
¡Do not bend disc.
¡When not in use, keep disc in the case.
Do not use discs that fit any of the descriptions given
below. Using these discs may damage the discs or
cause the unit to malfunction.
¡Special discs in a shape which is not round
¡Partly or wholly transparent disc
*Wholly semi-transparent disc may not be played back.
¡Discs with adhered labels, etc. on them
¡Damaged or deformed discs
Discs with burrsPlease remove the burrs
before use.
Discs with cracks,
scratches or parts missing Shoddily made discs
Disc accessories (stabiliz-
ers, etc.) Protective films or sheets
Labels created by a printer Disc with adhered stickers
or tape
Partly transparent disc Wholly transparent disc*
Disc insert
The surfaces of new discs tend to be slippery. Therefore,
when using such a disc for the first time, it may not load
satisfactorily even when it has been inserted into the
unit.  At a time like this, insert the disc into the unit as far
as it will go until it is loaded properly.
¡When inserting a disc into or ejecting and removing
it from the unit, insert it straight in or eject and
remove it straight out in parallel with the unit.
Otherwise, the disc may be scratched or marked in
the process.
¡When inserting a disc, do not put one disc on anoth-
er.  Failure to observe this may cause the discs to
be jammed.
Do not leave discs in the following places:
¡Direct sunlight
¡Near car heaters
¡Dirty, dusty and damp areas
¡On seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label in a heavy pen or ballpoint
pen.
Notes on CD-Rs/RWs, 
DVD–Rs/RWs
¡You may have trouble playing back some CD-R/RW,
DVD-Rs/RWs discs recorded on CD/DVD recorders
(CD-R/RW, DVD–Rs/RWs drives), either due to their
recording characteristics or dirt, fingerprints, scratch-
es, etc. on the disc surface.
¡CD-R/RW, DVD–Rs/RWs discs are less resistant to
high temperatures and high humidity than ordinary
music CDs.  Leaving them inside a car for extended
periods may damage and make playback impossible.
¡The unit may not successfully playback a CD-R/RW,
DVD–Rs/RWs that was made by the combination of
writing software, a CD/DVD recorder (CD-R/RW,
DVD–Rs/RWs drive) and a disc if they are incompati-
ble with one another.
¡This player does not play CD-R/RW, DVD–Rs/RWs
discs if the session is not closed.
¡Be sure to observe the handling instructions of CD-
R/RW, DVD–Rs/RWs discs.
¡This player does not play CD-R/RW discs which con-
tain other than CD-DA or MP3/WMA data.
 
Printed side 
						

							48
49CQ-VD7005U
English
Language Code List
8277 Rhaeto-Romance
8279 Romanian
8285 Russian
8365 Sanskrit
8368 Sindhi
8372 Serbo-Croatian
8373 Singhalese
8375 Slovak
8376 Slovenian
8377 Samoan
8378 Shona
8379 Somali
8381 Albanian
8382 Serbian
8385 Sundanese
8386 Swedish
8387 Swahili
8465 Tamil
8469 Telugu
8471 Tajik
8472 Thai
8473 Tigrinya
8475 Turkmen
8476 Tagalog
8479 Tonga
8482 Turkish
8484 Tatar
8487 Twi
8575 Ukrainian
8582 Urdu
8590 Uzbek
8673 Vietnamese
8679 Volapük
8779 Wolof
8872 Xhosa
8979 Yoruba
9072 Chinese
9085 Zulu
Code Language Name
In “OTHER” cases... (apage 38)
Note:
¡Setting is finished and the display returns to the main menu.
¡For retrying selection during number entry, touch/press  /[RETURN]
.
DVD language menu (apage 38)
7289 Armenian
7365 Interlingua
7378 Indonesian
7383 Icelandic
7384 Italian
7387 Hebrew
7465 Japanese
7473 Yiddish
7487 Javanese
7565 Georgian
7575 Kazakh
7576 Greenlandic
7577 Cambodian
7578 Kannada
7579 Korean
7583 Kashmiri
7585 Kurdish
7589 Kirghiz
7665 Latin
7678 Lingala
7679 Laothian
7684 Lithuanian
7686 Latvian, Lettish
7771 Malagasy
7773 Maori
7775 Macedonian
7776 Malayalam
7778 Mongolian
7779 Moldavian
7782 Marathi
7783 Malay
7784 Maltese
7789 Burmese
7865 Nauru
7869 Nepali
7876 Dutch
7879 Norwegian
7982 Oriya
8065 Panjabi
8076 Polish
8083 Pashto, Pushto
8084 Portuguese
8185 Quechua
Code Language Name
6565 Afar
6566 Abkhazian
6570 Afrikaans
6577 Ameharic
6582 Arabic
6583 Assamese
6589 Aymara
6590 Azerbaijani
6665 Bashkir
6669 Byelorussian
6671 Bulgarian
6672 Bihari
6678 Bengali; Bangla
6679 Tibetan
6682 Breton
6765 Catalan
6779 Corsican
6783 Czech
6789 Welsh
6865 Danish
6869 German
6890 Bhutani
6976 Greek
6978 English
6979 Esperanto
6983 Spanish
6984 Estonian
6985 Basque
7065 Persian
7073 Finnish
7074 Fiji
7079 Faroese
7082 French
7089 Frisian
7165 Irish
7168 Scots Gaelic
7176 Galician
7178 Guarani
7185 Gujarati
7265 Hausa
7273 Hindi
7282 Croatian
7285 Hungarian
Code Language Name
Input the four digit language code pressing the buttons to .
Touch to determine. 
						

							49
50CQ-VD7005U
English
Definition of Terms
Dolby Digital
This fully discrete format divides the music signals
into 5.1 channels: Front Left (L), Front Right (R),
Center (C), Left Surround (LS), Right Surround (RS)
and Subwoofer (SW: 0.1 channel) for recording and
playback. The number of channels that are recorded
depends on the software. (1 to 5.1 channels)
Dolby Pro Logic
This format records signals from four channels
[Front Left (L), Front Right (R), Center (C), and
Monaural Surround (S)] in two channels, decodes
those channels through a Dolby Pro Logic decoder,
and then outputs the resulting signals in four chan-
nels.
dts
This format requires more data than Dolby Digital,
and provides higher quality surround playback.
Similar to Dolby Digital, this fully discrete format
divides the music signals into 5.1 channels: Front
Left (L), Front Right (R), Center (C), Left Surround
(LS), Right Surround (RS) and Subwoofer (SW: 0.1
channel) for recording and playback.
Interactive DVD
An interactive DVD is DVD software which includes
multiple angles, multiple plot endings, etc.
Letterbox screen
This refers to a screen on which the playback picture
of wide-screen DVDs or VCD (Video CD)s appears
with black bands running along the top and bottom.
LPCM (Linear PCM audio)
In this format, the audio signal is converted to digital
data and recorded in two channels without compres-
sion. Because the capacity of a DVD disc is large, it
can store more data with better accuracy than a CD.
Pan & Scan screen
This refers to a screen on which the playback picture
of wide-screen DVDs or VCD (Video CD)s is cut off
at the left and right sides. Playback control (VCD (Video CD))
If the VCD (Video CD) has “With Playback Control”
or others written on the disc surface or on the jacket,
the scenes or information to be viewed (or listened
to) can be selected interactively with the screen by
looking at the menu shown on the screen.
In these instructions, playback using the menu
screen is referred to as the “menu play” for video
CDs. This player supports Video CDs with playback
control.
Title, Chapter (DVD)
DVDs are divided into some large sections (titles) or
some small sections (chapters). Each section is
numbered; these numbers are called “Title number”
or “Chapter number”.
Track (Video CD/CD)
Video CDs or CDs are divided into some sections
(tracks). Each section is numbered; these numbers
are called “Track number”. Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”, and the 
double-D symbol are trademarks of Dolby
Laboratories. 
“DTS” and “DTS Digital Surround” are registered trade-
marks of Digital Theater Systems, Inc.
“This product incorporates copyright protection tech-
nology that is protected by U.S. patents and other
intellectual property rights. Use of  this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise author-
ized by Macrovision. Reverse engineering or disas-
sembly is prohibited.”
Chapter 1
Chapter 2……
Chapter 1…… Title 1 Title 2
Track 1Track 2Track 3Track ……