Panasonic Kx Tge260 Operating Instructions Manual

Turning on the answering system
r
emotely
1 Dial your phone number from a
touch-tone phone.
2 Let the phone ring 15 times.
RA long beep is heard.
3 Enter your remote access code within 10
seconds after the long beep.
RThe greeting message is played back.
R You can either hang up, or enter your
remote access code again and begin
remote operation (page 60). Answering system settings
Call screening
Handset / Base unit
*
 1
While a caller is leaving a message, you can
listen to the call through the unit’s...

Selecting “
G reeting only ”
You can select  “Greeting only ” which sets
the unit to announce a greeting message to
callers but not record messages.
Select  “Greeting only ” in step 2 on
“Caller’s recording time”, page 61.
Note:
R When you select  “Greeting only ”:
– If you do not record your own message, the unit will play the pre-recorded
greeting-only message asking callers to
call again later.
– If you use your own message, record the greeting-only message asking callers to
call again later (page...

Voice mail service for
l andline
Voice mail is an automatic answering service
offered by your service provider/telephone
company. After you subscribe to this service,
your service provider/telephone company’s
voice mail system answers calls for you when
you are unavailable to answer the phone or
when your line is busy. Messages are
recorded by your service provider/telephone
company, not your telephone. Please contact
your service provider/telephone company for
details of this service.
Important:
R To...

Listening to voice mail messages
T
he unit lets you know that you have new
voice mail messages in the following way:
– “Voice mail msg. via phone co. ”
is displayed if message indication service is
available. Handset
1 MM

ENUN#330
R The speakerphone turns on.
2 Follow the pre-recorded instructions.
3 When finished, press  MOFF N.
Note:
R You can also use the  MACCESS N soft key,
if displayed, to play new voice mail
messages.
R If the handset still indicates there are new
messages even after you have...

3
Insert the hooks on the wall mounting
adaptor into holes ( ) and ( ) on the
b
ase unit. 4
A
djust the adaptor to hold the base unit,
then push it in the direction of the arrow
until it clicks into place. 5
M
ount the unit on a wall then slide down
to secure in place.  AC adaptor cord
R T

his product is compliant with the
following wall phone plate sizes (2
types).  83 mm (3 
1
/4  
 inches)  102 mm (4 inches)
F

it the slots of the unit onto the
corresponding wall phone plate tabs
for ( ) and ( )...

Charger
D
rive the screws ( ) (not supplied) into the
w

all.  27.2 mm (1 
1
/1
 6 inches) 66
For assistance, please visit http://www.panasonic.com/helpUseful Information
TGE26x_27x(en)_0123_ver110.pdf   662015/01/23   9:57:451 2 1 2  

Error messages
Display message Cause/solution
Ask phone
c ompany for
VM access # R
You have not stored the voice mail access number.
Store the number (page 63).
Base no power
o
 r
No link. Re-
connect base
AC adaptor.
or
No link. R
The handset has lost communication with the base
unit. Move closer to the base unit and try again.
R Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset’s registration may have been canceled.
Re-register the handset (page...

Display message Cause/solution
Requires
s ubscription
to Caller ID. R
You must subscribe to a Caller ID service. Once you
receive caller information after subscribing to a Caller
ID service, this message will not be displayed.
Use
r
 echargeable
battery. R
A wrong type of battery such as Alkaline or
Manganese was inserted. Use only the rechargeable
Ni-MH batteries noted on page 4, 8. Troubleshooting
I
 f you still have difficulties after following the instructions in this section, disconnect the base...

Problem Cause/solution
I cannot connect a cellular
p hone to the base unit. R
Confirm that your cellular phone is turned on.
RConfirm that your cellular phone is within base unit range
(page 14).
R Your cellular phone’s Bluetooth feature is turned off. Turn
it on.
R Depending on the state of the wireless environment, such
as the presence of any electrical interference, there may
be a delay even if the auto connection feature is turned
on. You can connect to the base unit manually (page 20).
R The...

Making/answering calls, intercom
Problem Cause/solution
 is displayed.
R
The handset is too far from the base unit. Move closer.
RThe base unit’s AC adaptor is not properly connected.
Reconnect AC adaptor to the base unit.
R The handset is not registered to the base unit. Register it
(page 48).
Noise is heard, sound cuts in
a
 nd out. R
You are using the handset or base unit in an area with
high electrical interference. Re-position the base unit and
use the handset away from sources of interference.
R...