Panasonic Kx Tgd6841 Operating Instructions Manual

							Wall mounting
T he base unit can be mounted on a wall by
changing the wall mounting adaptor’s position.
Note:
R Make sure that the wall and the fixing
method are strong enough to support the
weight of the unit. Base unit
1
T

o remove the wall mounting adaptor,
push down the release levers ( A).
Remove the adaptor ( B). 2
A 
Turn the adaptor so that the words
“UP WALL” are facing up.
B Tuck the telephone line cord inside the
wall mounting adaptor.
C  Connect the AC adaptor cord and
telephone line cord. 3
I
nsert the lower tabs of the adaptor into
the unit’s bottom slots ( A), then insert by
pushing down the levers of the adaptor
into the upper slots ( B).
R The words “UP WALL” should be
facing up. 4
M
ount the unit on a wall then slide down
to secure in place. Charger
D

rive the screws (not supplied) into the wall. For assistance, please visit http://www.panasonic.com/help
51Useful Information
TG684x7x(en)_1127_ver021.pdf   512012/11/27   18:16:49AA
AA
B BB
B 3
12
Hook A A
A A B BB B 83 mm 
(31/4 inches)
or
102 mm 
(4 inches)
21
Wall phone plate
102 mm
83 mm 
(4 inches)
1
2 (3
1/4 inches) Screws 27.2 mm
(“inches)
1/16  
						

							Error messages
Display message Cause/solution
Base no power
o r
No link. Re-connect base
AC adaptor.
or
No link. R
The handset has lost communication with the base
unit. Move closer to the base unit and try again.
R Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset’s registration may have been canceled.
Re-register the handset (page 35).
R When  “No link. ” is displayed during a power
failure, place a handset on the base unit to supply
power to the base unit.
Busy RT
he called unit is in use.
ROther units are in use and the system is busy. Try
again later.
R The handset you are using is too far from the base
unit. Move closer and try again.
Call phone company for
y
 our access # R
You have not stored the voice mail access number.
Store the number (page 47).
Check tel line RT
he supplied telephone line cord has not been
connected yet or not connected properly. Check the
connections (page 10).
Error!! RR
ecording was too short. Try again.
Invalid RT
here is no handset registered to the base unit
matching the handset number you entered.
R The handset is not registered to the base unit.
Register the handset (page 35).
Requires subscription to
C
 aller ID. R
You must subscribe to a Caller ID service. Once you
receive caller information after subscribing to a Caller
ID service, this message will not be displayed.
Use rechargeable battery. RA
 wrong type of battery such as Alkaline or
Manganese was inserted. Use only the rechargeable
Ni-MH batteries noted on page 5, 7. 52
For assistance, please visit http://www.panasonic.com/helpUseful Information
TG684x7x(en)_1127_ver021.pdf   522012/11/27   18:16:49 
						

							Troubleshooting
I f you still have difficulties after following the instructions in this section, disconnect the base unit’s
AC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset,
and then insert the batteries into the handset again. General use
Problem Cause/solution
The handset does not turn on
e
 ven after installing charged
batteries. R
Place the handset on the base unit or charger to turn on
the handset.
The unit does not work. RM
ake sure the batteries are installed correctly (page 10).
RFully charge the batteries (page 10).
R Check the connections (page 10).
R Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset has not been registered to the base unit.
Register the handset (page 35).
I cannot hear a dial tone. RT
he base unit’s AC adaptor or telephone line cord is not
connected. Check the connections.
R Disconnect the base unit from the telephone line and
connect the line to a known working telephone. If the
working telephone operates properly, contact our service
personnel to have the unit repaired. If the working
telephone does not operate properly, contact your service
provider/
telephone company.
The base unit beeps. RN
ew messages have been recorded. Listen to the new
messages (page 41). Programmable settings
Problem Cause/solution
The display is in a language I
c
 annot read. R
Change the display language (page 14).
I cannot register a handset to a
b
 ase unit. R
The maximum number of handsets (6) is already
registered to the base unit. Cancel unused handset
registrations from the base unit (page 35). Battery recharge
Problem Cause/solution
The handset beeps and/or  flashes.
R
B
attery charge is low. Fully charge the batteries (page 10). For assistance, please visit http://www.panasonic.com/help
53Useful Information
TG684x7x(en)_1127_ver021.pdf   532012/11/27   18:16:49  
						

							Problem Cause/solution
I fully charged the batteries, but
–  still flashes,
–  is displayed, or
–
the operating time seems to be shorter. R
C
lean the battery ends ( ,  ) and the charge contacts
w
ith a dry cloth and charge again.
R It is time to replace the batteries (page 10). Making/answering calls, intercom
Problem Cause/solution
 is displayed.
R
T
he handset is too far from the base unit. Move closer.
RThe base unit’s AC adaptor is not properly connected.
Reconnect AC adaptor to the base unit.
R The handset is not registered to the base unit. Register it
(page 35).
Noise is heard, sound cuts in
a
 nd out. R
You are using the handset or base unit in an area with
high electrical interference. Re-position the base unit and
use the handset away from sources of interference.
R Move closer to the base unit.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base unit and
the telephone line jack. Contact your DSL/ADSL provider
for details.
The handset does not ring. RT
he ringer volume is turned off. Adjust the ringer volume
(page 17, 28).
R Silent mode is turned on. Turn it off (page 32).
The base unit does not ring. RT
he ringer volume is turned off. Adjust the ringer volume
(page 17, 30).
R Silent mode is turned on. Turn it off (page 32).
I cannot make a call. RT
he dialing mode may be set incorrectly. Change the
setting (page 15).
I cannot make long distance
c
 alls. R
Make sure that you have long distance service. 54
For assistance, please visit http://www.panasonic.com/helpUseful Information
TG684x7x(en)_1127_ver021.pdf   542012/11/27   18:16:49      
						

							Caller ID/Talking Caller ID
Problem Cause/solution
Caller information is not
d isplayed. R
You must subscribe to Caller ID service. Contact your
service provider/telephone company for details.
R If your unit is connected to any additional telephone
equipment such as a Caller ID box or cordless telephone
line jack, plug the unit directly into the wall jack.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base unit and
the telephone line jack. Contact your DSL/ADSL provider
for details.
R The name display service may not be available in some
areas. Contact your service provider/
telephone company for details.
R Other telephone equipment may be interfering with this
unit. Disconnect the other equipment and try again.
Caller information is displayed
o
 r announced late. R
Depending on your service provider/telephone company,
the unit may display or announce the caller’s information
at the 2nd ring or later.
R Move closer to the base unit.
Caller information is not
a
 nnounced. R
The handset or base unit’s ringer volume is turned off.
Adjust it (page 17, 28, 30).
R The Talking Caller ID feature is turned off. Turn it on
(page 28, 30).
R The number of rings for the answering system is set to  “2
rings ” or  “Toll saver ”. Select a different setting
(page 45).
R If the base unit and another handset are having an
intercom call, your handset does not announce caller
information.
The caller list/incoming phone
n
 umbers are not edited
automatically. R
The Caller ID number auto edit feature is turned off. Turn
it on and try again (page 29, 31).
R You need to call back the edited number to activate Caller
ID number auto edit.
I cannot dial the phone number
e
 dited in the caller list. R
The phone number you dialed might have been edited
incorrectly (for example, the long distance “1” or the area
code is missing). Edit the phone number with another
pattern (page 37).
Time on the unit has shifted. RI
ncorrect time information from incoming Caller ID
changes the time. Set the time adjustment to
“Manual ” (off) (page 28). For assistance, please visit http://www.panasonic.com/help
55Useful Information
TG684x7x(en)_1127_ver021.pdf   552012/11/27   18:16:49 
						

							Problem Cause/solution
The 2nd caller’s information is
n ot displayed during an outside
call. R
In order to use Caller ID, call waiting, or Call Waiting
Caller ID (CWID), you must first contact your service
provider/telephone company and subscribe to the desired
service.
After subscribing, you may need to contact your service
provider/telephone company again to activate this specific
service, even if you already subscribed to both Caller ID
and Call Waiting with Caller ID services (CWID). Answering system
Problem Cause/solution
The unit does not record new
m
 essages. R
The answering system is turned off. Turn it on (page 40).
RThe message memory is full. Erase unnecessary
messages (page 41).
R The recording time is set to  “Greeting only ”. Change
the setting (page 46).
R If you subscribe to a voice mail service, messages are
recorded by your service provider/telephone company,
not your telephone. Change the unit’s number of rings
setting or contact your service provider/telephone
company (page 46).
I cannot operate the answering
s
 ystem remotely. R
The remote access code is not set. Set the remote
access code (page 44).
R You are entering the wrong remote access code. If you
have forgotten your remote access code, enter the
remote access code setting to check your current code
(page 44).
R The answering system is turned off. Turn it on (page 45).
The unit does not emit the
s
 pecified number of rings. R
If the first ring is turned off, the number of rings decreases
by 1 from the specified number of rings. Liquid damage
Problem Cause/solution
Liquid or other form of moisture
h
 as entered the handset/base
unit. R
Disconnect the AC adaptor and telephone line cord from
the base unit. Remove the batteries from the handset and
leave to dry for at least 3 days. After the handset/base
unit are completely dry, reconnect the AC adaptor and
telephone line cord. Insert the batteries and charge fully
before use. If the unit does not work properly, contact an
authorized service center. Caution:
R
T

o avoid permanent damage, do not use a microwave oven to speed up the drying process.
56 For assistance, please visit http://www.panasonic.com/helpUseful Information
TG684x7x(en)_1127_ver021.pdf   562012/11/27   18:16:49 
						

							FCC and other information
For assistance, please visit http://www.panasonic.com/help
57Useful InformationTG684x7x(en)_1127_ver021.pdf   572012/11/27   18:16:49This equipment complies with Part 68 of the 
FCC rules and the requirements adopted by 
the ACTA. On the bottom of this equipment 
is a label that contains, among other 
information, a product identifier in the 
format US:ACJ----------.
If requested, this number must be provided 
to the telephone company.
L Registration No.............(found on the 
bottom of the unit)
L Ringer Equivalence No. (REN).......0.1B
A plug and jack used to connect this 
equipment to the premises wiring and 
telephone network must comply with the 
applicable FCC Part 68 rules and 
requirements adopted by the ACTA. A 
compliant telephone cord and modular plug 
is provided with the product. It is designed 
to be connected to a compatible modular 
jack that is also compliant.
The REN is used to determine the number 
of devices that may be connected to a 
telephone line. Excessive RENs on a 
telephone line may result in the devices not 
ringing in response to an incoming call. In 
most but not all areas, the sum of RENs 
should not exceed five (5.0). To be certain 
of the number of devices that may be 
connected to a line, as determined by the 
total RENs, contact the local telephone 
company. For products approved after July 
23, 2001, the REN for the product is part of 
the product identifier that has the format 
US:AAAEQ##TXXXX. The digits 
represented by ## are the REN without a 
decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the 
telephone network, the telephone company 
will notify you in advance that temporary 
discontinuance of service may be required. 
But if advance notice isnt practical, the 
telephone company will notify the customer 
as soon as possible. Also, you will beadvised of your right to file a complaint with 
the FCC if you believe it is necessary.
The telephone company may make changes 
in its facilities, equipment, operations or 
procedures that could affect the operation of 
the equipment. If this happens the 
telephone company will provide advance 
notice in order for you to make necessary 
modifications to maintain uninterrupted 
service.
If trouble is experienced with this 
equipment, for repair or warranty 
information, please contact a Factory 
Service Center or other Authorized Servicer. 
If the equipment is causing harm to the 
telephone network, the telephone company 
may request that you disconnect the 
equipment until the problem is resolved.
Connection to party line service is subject to 
state tariffs. Contact the state public utility 
commission, public service commission or 
corporation commission for information.
If your home has specially wired alarm 
equipment connected to the telephone line, 
ensure the installation of this equipment 
does not disable your alarm equipment. If 
you have questions about what will disable 
alarm equipment, consult your telephone 
company or a qualified installer.
This equipment is hearing aid compatible as 
defined by the FCC in 47 CFR Section 
68.316.
When you hold the phone to your ear, noise 
might be heard in your Hearing Aid. Some 
Hearing Aids are not adequately shielded 
from external RF (radio frequency) energy. If  
noise occurs, use an optional headset 
accessory or the speakerphone option (if 
applicable) when using this phone. Consult 
with your audiologist or Hearing Aid  
						

							58
For assistance, please visit http://www.panasonic.com/helpUseful InformationTG684x7x(en)_1127_ver021.pdf   582012/11/27   18:16:49manufacturer about the availability of 
Hearing Aids which provide adequate 
shielding to RF energy commonly emitted 
by digital devices.
WHEN PROGRAMMING EMERGENCY 
NUMBERS AND(OR)  MAKING TEST 
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to 
the dispatcher the reason for the call.
2) Perform such activities in the off-peak 
hours, such as early morning or late 
evenings.
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
interference, and (2) this device must 
accept any interference received, including 
interference that may cause undesired 
operation.
Privacy of communications may not be 
ensured when using this phone.
CAUTION:
Any changes or modifications not expressly 
approved by the party responsible for 
compliance could void the user’s authority 
to operate this device.
NOTE:
This equipment has been tested and found 
to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC 
Rules. These limits are designed to provide 
reasonable protection against harmful 
interference in a residential installation. This 
equipment generates, uses, and can radiate 
radio frequency energy and, if not installed 
and used in accordance with the 
instructions, may cause harmful 
interference to radio communications. 
However, there is no guarantee that 
interference will not occur in a particular 
installation. If this equipment does cause 
harmful interference to radio or television 
reception, which can be determined by
turning the equipment off and on, the user isencouraged to try to correct the interference 
by one or more of the following measures:
– Reorient or relocate the receiving 
antenna.
– Increase the separation between the 
equipment and receiver.
– Connect the equipment into an outlet on a 
circuit different from that to which the 
receiver is connected.
– Consult the dealer or an experienced 
radio/TV technician for help.
Some cordless telephones operate at 
frequencies that may cause interference to 
nearby TVs and VCRs. To minimize or 
prevent such interference, the base of the 
cordless telephone should not be placed 
near or on top of a TV or VCR. If  
interference is experienced, move the 
cordless telephone further away from the TV 
or VCR. This will often reduce or eliminate 
interference.
FCC RF Exposure Warning:
L This product complies with FCC radiation 
exposure limits set forth for an 
uncontrolled environment. 
L To comply with FCC RF exposure 
requirements, the base unit must be 
installed and operated 20 cm (8 inches) 
or more between the product and all 
person’s body (excluding extremities of 
hands, wrist and feet). 
L This product may not be collocated or 
operated in conjunction with any other 
antenna or transmitter.
L The handset may be carried and operated 
with only the specific provided belt-clip. 
Other non-tested belt-clips or similar 
body-worn accessories may not comply 
and must be avoided.
Notice:
L FCC ID can be found inside the battery 
    compartment or on the bottom of the 
units.  
						

							For assistance, please visit http://www.panasonic.com/help
59Useful InformationTG684x7x(en)_1127_ver021.pdf   592012/11/27   18:16:49Compliance with TIA-1083 standard: 
Telephone handsets identified with this logo 
have reduced noise and interference when 
used with T-Coil equipped hearing aids and 
cochlear implants.
T
Compatible with
Hearing Aid T-Coil
TIA-1083  
						

							Guía Rápida Española
60
Para obtener ayuda, visite http://www.panasonic.com/help (solo en inglés) Guía Rápida EspañolaTG684x7x(en)_1127_ver021.pdf   602012/11/27   18:16:49Instalación
Unidad base
LUse solo el adaptador de corriente Panasonic PNLV226 incluido.
CARGUE
APROXIMADAMENTE
DURANTE 7 HORASAuricular
Cargador
LUTILICE SOLO baterías de Ni-MH tamaño AAA (R03). LNO utilice baterías Alcalinas, de Manganeso o de Ni-Cd.LCompruebe que las polaridades son las correctas (S,T).
A la toma
de corriente
A la toma
de corriente
Correcto Incorrecto
*Se requiere un filtro DSL/ADSL (no incluido) si tiene servicio de DSL/ADSL.
A la toma de
teléfono de línea
única (RJ11C)
Filtro DSL/ADSL*
Gancho
Oprima firmemente
el contacto. 
SOLO baterías Ni-MH recargables
Confirme que
aparezca
“Cargando”. “Clic”
“Clic”