Panasonic Kx Tg2480 Operating Instructions Manual

Preparation
For assistance, please visit http://www.panasonic.com/consumersupport11
If you use the unit as a single-line telephone only
TRANSPARENT plug
LINE 1
2-Wire telephone line cord
with TRANSPARENT plugsTo single-line 
telephone jack (RJ11C)
TG2480(e).book  Page 11  Monday, March 28, 2005  3:31 PM 

Preparation
12For assistance, please visit http://www.panasonic.com/consumersupport
If you subscribe to a DSL service
LPlease attach a noise filter (contact your DSL provider) to the telephone line between 
the base unit and the telephone line jack in the event of the following:
– Noise is heard during conversations.
– Caller ID features (page 29) do not function properly.
Connecting a 2 line telephone jack
For this connection, please purchase the Panasonic T-adaptor KX-J42. See page 5 for 
ordering...

Preparation
For assistance, please visit http://www.panasonic.com/consumersupport13
Connecting 2 single-line telephone jacks
Example: DSL line is LINE 2
12-wire telephone line cord with TRANSPARENT plugs
24-wire telephone line cord with GREEN plugs
2
1
TRANSPARENT
plugGREEN
plugLINE 2
Noise filter
LINE 1 To single-line 
telephone jacks (RJ11C)
(For DSL users)
TG2480(e).book  Page 13  Monday, March 28, 2005  3:31 PM 

Preparation
14For assistance, please visit http://www.panasonic.com/consumersupport
Battery installation
1Insert the battery (1), and press it 
down until it snaps into the 
compartment (2).
2Close the handset cover.
Battery charge
Place the handset on the base unit for 6 
hours before initial use.
LThe unit will beep once, the CHARGE 
indicator will light, and “Charging” will 
be displayed.
L“Charge completed” is displayed 
when the battery has been fully charged. 
The CHARGE indicator will remain lit....

Preparation
For assistance, please visit http://www.panasonic.com/consumersupport15
Battery strength
You can confirm the battery strength on the 
handset display.
Recharging the battery
Recharge the battery when:
–“Recharge battery” is displayed or 
7 flashes on the handset display.
– the handset beeps intermittently while it 
is in use.
Note:
LRecharge the handset battery for more 
than 15 minutes, or the display will 
continue showing the indication.
LIf the battery has been discharged, the 
handset...

Preparation
16For assistance, please visit http://www.panasonic.com/consumersupport
Battery replacement
If battery performance diminishes, make 
sure you have cleaned the charge 
contacts and fully charged the battery. The 
battery needs to be replaced if any of the 
following are displayed after a few phone 
calls even when you have fully charged the 
battery.
–“Recharge battery”
–7 (flashing)
–“Charge for 6h”
–8
LUse only the rechargeable Panasonic 
battery noted on page 5.
1Press the notch on the...

Preparation
For assistance, please visit http://www.panasonic.com/consumersupport17
Controls and display
Controls
Base unit
AHook
BLINE 1 indicator
CLINE 2 indicator
DV.M. (Voice Mail) indicator
EAntenna
FCharge contacts
GCHARGE indicator
LOCATOR indicator
H{HANDSET LOCATOR}
ABC D E
FGH
TG2480(e).book  Page 17  Monday, March 28, 2005  3:31 PM 

Preparation
18For assistance, please visit http://www.panasonic.com/consumersupport
Handset
ASpeaker
BSoft key
CHeadset jack
D{C} (TALK)
ENavigator key
F{s} (SP-PHONE)
G{*} (TONE)
H{HOLD}
IRinger indicator
Message indicator
JReceiver
KDisplay
L{OFF}
M{MENU}
N{FLASH} {CALL WAIT}
O{REDIAL} {PAUSE}
PMicrophone
QCharge contactsUsing the navigator key
The handset navigator key can be used to 
navigate through menus and to select 
items shown on the display, by pressing 
{^} or {V}.
Display
Handset display...

Preparation
For assistance, please visit http://www.panasonic.com/consumersupport19
Soft keys
The handset features 2 soft keys. By 
pressing a soft key, you can select the 
function displayed directly above it.
LThe functions displayed will vary 
depending on how you are using the 
unit.
LWhen a function does not appear above 
a soft key, the soft key has no function.
Soft key examples:
Backlit display and handset keypad
The handset display and the dialing 
buttons will light for a few seconds after...

Making/Answering Calls
20For assistance, please visit http://www.panasonic.com/consumersupport
Making calls
1Lift the handset and press {C}.
LAn available line is automatically 
selected and the line is displayed (to 
change the line selection, see page 
40).
LYou can select a line by pressing 
{Line1} or {Line2}, instead of 
pressing {C}.
L“Talk” will be displayed.
2Dial the phone number.
3When finished talking, press {OFF} or 
place the handset on the base unit.
Note:
Lk and l show the status of each...