Panasonic Kx Tg2239 Operating Instructions Manual

11
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Settings
Connections
•USE ONLY WITH Panasonic AC ADAPTOR PQLV1 (Order No. PQLV1Z).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
•To connect a standard telephone on the same line, see page 60.
•If your unit is connected to a PBX which does not support Caller ID and voice
mail services, you cannot access those services.
Single-Line
Telephone Jack
(RJ11C)
Telephone Line Cord
AC...

12
Settings
Battery Charge
Place the handset on the base unit and charge for about 15 hoursbefore
initial use.
•The CHARGE indicator lights and a beep sounds. 
Installing the Battery in the Handset
CHARGE Indicator
OR
Insert the battery into the handset as shown, matching the correct polarity
(
#). Press the battery down until it places into the compartment ($).
When finished, close the cover.
2
1 

13
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Up to 11 days
OperationOperating time
While in use (TALK)Up to 4.5 hours
While not in use (Standby)
•The battery operating time may be shortened depending on usage conditions,
such as viewing the Caller ID Caller List or directory list, and ambient
temperature.
•Clean the handset and the base unit charge contacts with a soft, dry cloth
once a month. Clean more often if the unit is subject to grease, dust or
high humidity.Otherwise the...

14
Dialing Mode
If you have touch tone service, set to “Tone”. If rotary or pulse service is
used, set to “Pulse”. Your phone comes from the factory set to “Tone”.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (FUNCTION).
2
Scroll to “Program” by pressing Öor Ñ.
3
Press á.
4
Scroll to “Set dial mode” by pressing
Öor Ñ.
5
Press á.
6
Select “Pulse” or “Tone” by pressing Ö
or Ñ.
7
Press á(Savekey).
•A beep sounds.
•To exit the programming mode, press (OFF).
•You...

15
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Line Mode
If the line is connected to a low voltage system such as a PBX, set to “B”.
Your phone comes from the factory set to “A”. 
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (FUNCTION).
2
Scroll to “Program” by pressing Öor Ñ.
3
Pressá.
4
Scroll to “Set line mode” by pressing
Öor Ñ.
5
Press á.
6
Select “B” or “A” by pressing Öor Ñ.
7
Press á(Savekey).
•A beep sounds.
•To exit the programming...

--------------
HSave directory
Ringer volume
Ringer tone
Program
--------------To store an item in the directory (p. 40).
To select the ringer volume (p. 18).
To select the ringer tone (p. 19).
--------------
HSet flash time
Save VM acces#
VM tone detect
Set line mode
Set dial mode
Auto talk
CallerID edit
LCD contrast
--------------
16
Programmable Functions
You can program the following function items using the handset near
the base unit. The display shows the programming instructions. See the...

17
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Auto Talk Feature
The Auto Talk feature allows you to answer a call by lifting the handset off
the base unit without pressing  or  . If you want to use this
feature, turn the feature ON by programming. Your phone comes from the
factory set to OFF.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (FUNCTION).
2
Scroll to “Program” by pressing Öor Ñ.
3
Pressá.
4
Scroll to “Auto talk” by pressing Öor
Ñ....

18
Programmable Functions
Ringer Volume
You can program the handset or base unit ringer volume to HIGH, LOW
or OFF. If set to OFF, the handset or base unit will not ring. Your phone
comes from the factory set to HIGH.
Make sure the unit is not being used and the handset is lifted off the
base unit.
With the handset
1
Press (FUNCTION).
2
Scroll to “Ringer volume” by
pressing 
Öor Ñ.
3
Press á.
4
Select the desired volume by
pressing 
Öor Ñ.
•Each time you press Öor Ñ, the volume
will change and ring.
•If...

19
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Ringer Tone
You can select the handset or the base unit ringer tone out of 6 patterns.
When an incoming call is being received, the unit rings in the selected
tone.
Your phone comes from the factory set to 1.
Make sure the unit is not being used and the handset is lifted off the
base unit.
With the handset
1
Press (FUNCTION).
2
Scroll to “Ringer tone” by pressingÖor
Ñ.
3
Press á.
•The current setting is displayed.
4
Select the desired...

20
LCD Contrast
You can program the handset LCD contrast (5 levels). To make the
handset display clearer, set to high level. Your phone comes from the
factory set to level 3.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (FUNCTION).
2
Scroll to “Program” by pressing Öor Ñ.
3
Press á.
4
Scroll to “LCD contrast” by pressing Ö
or Ñ.
5
Pressá.
6
Select the desired contrast by pressing Ö
or Ñ.
•Each time you press Öor Ñ, the LCD
contrast will change. 
7
Press...