Panasonic Kx Tg2219 Operating Instructions Manual

							51
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4
Connect the telephone line cord.
Mount the unit, then slide down.
•Raise the antenna.
•Fasten the telephone line cord to
prevent it from being disconnected.
5
To charge the handset battery:
Fix the charge contacts (#) and insert
the hook to the handset hole ($).
•The IN USE/CHARGE/HOLD indicator
lights.
2
1
Hook
Hole
Hooks
OR 
						

							52
Battery Replacement
A nickel cadmium battery that is recyclable powers the
product you have purchased. At the end of its useful life,
under various state and local laws, it is illegal to dispose of
this battery into your municipal waste stream. Please call 
1-800-8-BATTERY for information on how to recycle this
battery. If “Recharge” is displayed and/or “” flashes after a few telephone
calls even if the battery was fully charged, replace the battery with a new
Panasonic N4HKGMA00001 (P-P511) battery. To order, call the
accessories telephone number on page 2.
1
Press the notch on the
handset cover firmly and
slide it as indicated by the
arrow.
2
Remove the old battery. Insert
the new battery into the
handset as shown, matching
the correct polarity (#). 
Press the battery down 
until it places into the
compartment ($).
3
Close the cover. Make sure you charge the new battery for about
15 hours in order to display the battery strength prompt correctly
(p. 12).
2
1 
						

							53
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Adding Another Phone
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard Telephone
Single-Line
Telephone Jack
T-Adaptor (KX-J66)Telephone
Line Cord 
						

							54
Troubleshooting
Problem
The unit does not work.
“No link to base
Place on cradle and
try again.” is displayed
and an alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The unit does not ring.
The handset display is blank.
You cannot program items,
such as the dialing mode.
Remedy
•Check the settings (p. 11–15).
•Charge the battery fully (p. 12).
•Clean the charge contacts and charge
again (p. 13).
•Install the battery properly (p. 12).
•Place the handset on the base unit and
unplug the AC adaptor to reset. Plug in,
and try again.
•Re-install the battery and place the
handset on the base unit (p. 52). Try
again.
•You are too far from the base unit. Move
closer and try again.
•Place the handset on the base unit and
try again.
•Plug in the AC adaptor.
•Raise the base unit antenna.
•Locate the handset and the base unit
away from other electrical appliances
(p. 3).
•Move closer to the base unit.
•Raise the base unit antenna.
•Press 
Üto select a clearer channel in
the talk or speakerphone mode.
•The ringer volume is set to OFF. Set to
HIGH or LOW (p. 18).
•Charge the battery fully (p. 12).
•Programming is not possible while the
unit is in the talk or speakerphone mode,
when viewing the Caller List/directory list.
•Do not pause for over 60 seconds while
programming.
•Move closer to the base unit.
•
Ö, Ñ, Üor ámay have been
pressed when you picked up the
handset. Press 
(OFF)and try again. 
						

							55
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
Previously programmed
information is erased.
You cannot store a name
and phone number in the
directory.
While programming or
searching, the unit starts to
ring and stops the program/
search.
The unit does not display the
caller’s name and/or phone
number.
The handset display exits
the Caller List.
When a second call is
received during a
conversation, the unit does
not display the new caller’s
name and/or phone number.
You cannot page the
handset.
Remedy
•If a power failure occurs, programmed
information may be erased. Reprogram
if necessary.
•You cannot store an item in the directory
while the unit is in the talk or speaker
mode.
•Do not pause for over 60 seconds while
storing.
•To answer the call, press or .
Start again from the beginning after
hanging up.
•You need to subscribe to a Caller ID
service.
•Other telephone equipment may be
interfering with your phone. Disconnect
it and try again.
•Other electrical appliances connected to
the same outlet may be interfering with
the Caller ID information.
•Telephone line noise may be affecting
the Caller ID information.
•Do not pause for over 60 seconds while
searching.
•The line mode selection is incorrect. See
page 15.
•The caller requested not to send his/her
information. See page 27.
•The handset is too far from the base unit.
•The handset is engaged in an outside
call, viewing the Caller List/directory list.
Wait until the IN USE/CHARGE/HOLD
indicator light goes out. 
						

							56
Problem
You cannot redial by
pressing 
(REDIAL/PAUSE).
“Recharge” is displayed,
“” flashes or the unit
beeps intermittently.
You charged the battery
fully, but “Recharge” is still
displayed and/or “”
continues to flash.
The IN USE/CHARGE/HOLD
indicator light does not go
out after the battery has
been charged.
You cannot have a
conversation using the
headset.
If you cannot solve your
problem
Remedy
•If the last number dialed was more than
32 digits long, the number will not be
redialed correctly.
•The button has a double function as
either redial or pause. It will redial the
last number dialed if pressed at the
outset of a call (p. 23). If another
number has been dialed first, it will
operate as a pause button (p. 47).
•Charge the battery fully (p. 12).
•Clean the charge contacts and charge
again (p. 13).
•Install a new battery (p. 52).
•This is normal.
•Make sure that an optional headset is
connected properly (p. 49).
•may have been pressed. 
If “SP-phone” is displayed on the
handset, press  to continue the
conversation with the headset.
•Call our customer call center at
1-800-211-PANA(7262).
•Panasonic’s e-mail address for customer
inquiries:
[email protected] 
for customers in the USA or Puerto Rico
ONLY
Troubleshooting 
						

							57
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Important Safety Instructions
When using this unit, basic safety precautions should always be followed
to reduce the risk of fire, electric shock, or personal injury.
11. Read and understand all instructions.
12. Follow all warnings and instructions marked on this unit.
13. Unplug this unit from AC outlets before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for cleaning.
14. Do not use this unit near water, for example, near a bathtub,
washbowl, kitchen sink, or the like.
15. Place this unit securely on a stable surface. Serious damage and/or
injury may result if the unit falls.
16. Do not cover slots and openings on the unit. They are provided for
ventilation and protection against overheating. Never place the unit
near radiators, or in a place where proper ventilation is not provided.
17. Use only the power source marked on the unit. If you are not sure of
the type of power supplied to your home, consult your dealer or local
power company.
18. Do not place objects on the power cord. Install the unit where no one
can step or trip on the cord.
19. Do not overload wall outlets and extension cords. This can result in
the risk of fire or electric shock.
10. Never push any objects through slots in this unit. This may result in
the risk of fire or electric shock. Never spill any liquid on the unit.
11. To reduce the risk of electric shock, do not disassemble this unit.
Take the unit to an authorized servicenter when service is required.
Opening or removing covers may expose you to dangerous voltages
or other risks. Incorrect reassembly can cause electric shock when
the unit is subsequently used.
12. Unplug this unit from the wall outlet and refer servicing to an
authorized servicenter when the following conditions occur:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the unit.
C. If the unit has been exposed to rain or water.
D. If the unit does not work normally by following the operating
instructions. Adjust only controls covered by the operating
instructions. Improper adjustment may require extensive work by
an authorized servicenter.
E. If the unit has been dropped or physically damaged.
F. If the unit exhibits a distinct change in performance.
13. During thunderstorms, avoid using telephones except cordless types.
There may be a remote risk of an electric shock from lightning.
14. Do not use this unit to report a gas leak, when in the vicinity of the
leak.
SAVE THESE INSTRUCTIONS 
						

							58CAUTION:
To reduce the risk of fire or injury to persons, read and follow these
instructions.
1. Use only the battery(ies) specified.
2. Do not dispose of the battery(ies) in a fire. They may explode. Check
with local waste management codes for special disposal instructions.
3. Do not open or mutilate the battery(ies). Released electrolyte is
corrosive and may cause burns or injury to the eyes or skin. The
electrolyte may be toxic if swallowed.
4. Exercise care in handling batteries in order not to short the battery to
conductive materials such as rings, bracelets, and keys. The battery
and/or conductor may overheat and cause burns.
5. Charge the battery(ies) provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in this manual.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR ANY TYPE OF MOISTURE. 
•The AC adaptor is used as the main disconnect device, ensure that the
AC outlet is located/installed near the unit and is easily accessible.
Important Safety Instructions 
						

							59
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
FCC and Other Information
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the bottom of this equipment is a label that contains,
among other information, a product identifier in the format US:ACJ-----. 
If requested, this number must be provided to the telephone company.
Registration No.  ....................................................(found on the bottom of the unit)
Ringer Equivalence No. (REN)...........................................................................0.1B
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular plug
is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. 
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is
part of the product identifier that has the format US:AAAEQ##TXXXX. The digits
represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). 
If this equipment causes harm to the telephone network, the telephone company
will notify you in advance that temporary discontinuance of service may be
required. But if advance notice isn’t practical, the telephone company will notify
the customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations
or procedures that could affect the operation of the equipment. If this happens the
telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information,
please contact a Factory Servicenter or other Authorized Servicer. If the
equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public
utility commission, public service commission or corporation commission for
information.
If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this equipment does not disable your alarm equipment. If
you have questions about what will disable alarm equipment, consult your
telephone company or a qualified installer. 
						

							60
FCC and Other Information
WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to the dispatcher the reason for the call.
2) Perform such activities in the off-peak hours, such as early morning or late
evenings.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Privacy of communications may not be ensured when using this phone.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.
Note:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Some cordless telephones operate at frequencies that may cause interference to
nearby TVs and VCRs. To minimize or prevent such interference, the base of the
cordless telephone should not be placed near or on top of a TV or VCR. If
interference is experienced, move the cordless telephone further away from the
TV or VCR. This will often reduce, or eliminate, interference.
Operating near 2.4GHz electrical appliances may cause interference. Move away
from the electrical appliances and/or press the CH (Channel) button.