Panasonic Kx Tda5480 Getting Started Manual

							4.3 Programming the VoIP Gateway Card in the Chicago Office
Getting Started 41
Assigning the IP Address
Note that the card in the Chicago office requires different IP address settings from the card in 
the Los Angeles office.
Assigning the Hunt Pattern
Note that the card in the Chicago office requires a different PBX code from the card in the Los 
Angeles office.1.Click 1.1 Network Settings, General in the 
main menu.
2.
a.In the IP Address box, type 
199.176.64.41.
b.In the Subnet Mask box, type 
255.255.255.0.
c.In the Default Gateway box, type 
199.176.64.1.
d.Click OK.
3.Confirm your entry, and then click OK.
1.Click 1.5 Hunt Pattern (for Incoming Calls) 
in the main menu.
2.
a.In the Hunt Pattern No. box, type 1.
b.In the Receive Leading Number box, 
type 41 (PBX code).
c.Click ENTRY.
d.Click OK.
3.Confirm your entry, and then click OK. 
						

							4.3 Programming the VoIP Gateway Card in the Chicago Office
42 Getting Started
Uploading Address Translation Table to the VoIP Gateway Card
For the VoIP Gateway Cards in the Los Angeles and Chicago offices to communicate properly 
over the VoIP network, the cards must share the same address translation table.
Follow the procedure below to upload the address translation table downloaded from the card 
in the Los Angeles office (see 4.2.6 Downloading the Address Translation Table from the VoIP 
Gateway Card) to the card in the Chicago office.
1.Click 3.3 Upload of DN2IP data (PC –> VoIP 
Gateway) in the main menu.
2.
a.Click Browse and choose a file to 
upload.
b.Click UPLOAD(PC–>VoIP Gateway).
3.Click REBOOT.
4.Click REBOOT. 
						

							4.3 Programming the VoIP Gateway Card in the Chicago Office
Getting Started 43
Note
For more details about uploading the address translation table, refer to 2.4.3 Upload of 
Address Translation Table of the VoIP Gateway Card Programming Guide.
Confirming the IP Address Assignment
Note that the card in the Chicago has been assigned a different IP address from the card in the 
Los Angeles office.
1.Set the IP address settings of the PC to the following values:
IP address: 199.176.64.100
Subnet Mask address: 255.255.255.0
2.Start Internet Explorer from the Start menu.
3.In the Address box of Internet Explorer, type http://199.176.64.41 (the new IP address of 
the card).
4.Press the ENTER key on the keyboard.
If you can log in, then the card has been successfully programmed.
After you have confirmed that the card has been successfully programmed, it is strongly 
recommended that you download the configuration data from the card and save it on your PC 
for backup and archive purposes.
The procedure for downloading the configuration data is provided in 2.4.2 Download of 
Configuration Data of the VoIP Gateway Card Programming Guide. 
						

							4.3 Programming the VoIP Gateway Card in the Chicago Office
44 Getting Started 
						

							Getting Started 45
Section 5
Programming the PBX
For successful operation of a VoIP network using the 
VoIP Gateway Card as a QSIG network interface, the 
PBX at each location in the network must be 
programmed appropriately. For a detailed discussion of 
related features, refer to the Hybrid IP-PBX Feature 
Guide.
This section details the procedure to program the PBX 
to use the card. 
						

							5.1 Programming the PBX in the Los Angeles Office
46 Getting Started
5.1 Programming the PBX in the Los Angeles 
Office
This section details the procedure to program the PBX in the Los Angeles office. After the PBX 
in the Los Angeles office has been fully programmed, repeat the procedure for the PBX in the 
Chicago office with the appropriate setting values (see 5.2 Programming the PBX in the 
Chicago Office).
Note
It is assumed that you have already installed the KX-TDA50 Maintenance Console (PC 
programming software for the KX-TDA50 PBX) in your PC.
1.Start the KX-TDA50 Maintenance Console 
from the Start menu.
2.
a.Type the Installer Level Programmer 
Code (default: INSTALLER).
b.Click OK.
3.
a.Click Connect  RS-232C or USB.
b.In the next screen, type the system 
password for installer (default: 1234).
c.Click OK.
The program menu appears.
4.
a.Double-click Configuration.
b.Double-click IP-GW Port.
Confirm that ports 1 and 2 are in service 
(INS).
5.
a.Double-click CO & Incoming Call.
b.Double-click CO Line Setting.
c.Type the CO Name and assign an 
unused Trunk Group Number to be 
used for all VoIP gateway trunks (CO 
lines).
d.Click OK. 
						

							5.1 Programming the PBX in the Los Angeles Office
Getting Started 47
Note
For details about network parameter settings, refer to the relevant sections of the Hybrid 
IP-PBX Feature Guide.6.
a.Double-click System.
b.Double-click Numbering Plan.
c.Double-click Feature.
d.In the Tie Line Access box, type the 
dialing number.
e.Click OK.
7.
a.Double-click Private Network.
b.In the Own PBX Code box, type 35 (the 
PBX code of the local PBX in the 
network).
c.In the Leading Number box, type 41 
(the PBX code of the remote PBX in the 
network).
d.In the corresponding Trunk Group list, 
click the number of the trunk (CO line) 
group to be used when making calls.
e.Set the number modification pattern, if 
necessary.
f.Click OK.
8.
a.Double-click Configuration.
b.Double-click Slot.
c.Click Status of the card.
d.Set the status to OUS.
e.Click Card Type of the card.
f.In the Va l u e list, click Overlap (default) 
or En-bloc
*1.
g.Click OK.
h.Click Status of the card.
i.Set the status to INS.
*1When En-bloc is selected, you need to press # after dialing the phone number. 
						

							5.2 Programming the PBX in the Chicago Office
48 Getting Started
5.2 Programming the PBX in the Chicago Office
This section details the procedure to program the PBX in the Chicago office. Follow the same 
procedure as you did for the PBX in the Los Angeles office, entering the setting values as 
appropriate for the Chicago office.
Note
It is assumed that you have already installed the KX-TDA Maintenance Console (PC 
programming software for the KX-TDA100/KX-TDA200 PBX) in your PC.
1.Start the KX-TDA Maintenance Console from 
the Start menu.
2.
a.Type the Installer Level Programmer 
Code (default: INSTALLER).
b.Click OK.
3.
a.Click Connect  RS-232C or USB.
b.In the next screen, type the system 
password for installer (default: 1234).
c.Click OK.
The program menu appears.
4.
a.Double-click Configuration.
b.Double-click IP-GW Port.
Confirm that ports 1 and 2 are in service 
(INS).
5.
a.Double-click CO & Incoming Call.
b.Double-click CO Line Setting.
c.Type the CO Name and assign an 
unused Trunk Group Number to be 
used for all VoIP gateway trunks (CO 
lines).
d.Click OK. 
						

							5.2 Programming the PBX in the Chicago Office
Getting Started 49
Note
For details about network parameter settings, refer to the relevant sections of the Hybrid 
IP-PBX Feature Guide.6.
a.Double-click System.
b.Double-click Numbering Plan.
c.Double-click Feature.
d.In the Tie Line Access box, type the 
dialing number.
e.Click OK.
7.
a.Double-click Private Network.
b.In the Own PBX Code box, type 41 (the 
PBX code of the local PBX in the 
network).
c.In the Leading Number box, type 35 
(the PBX code of the remote PBX in the 
network).
d.In the corresponding Trunk Group list, 
click the number of the trunk (CO line) 
group to be used when making calls.
e.Set the number modification pattern, if 
necessary.
f.Click OK.
8.
a.Double-click Configuration.
b.Double-click Slot.
c.Click Status of the card.
d.Set the status to OUS.
e.Click Card Type of the card.
f.In the Va l u e list, click Overlap (default) 
or En-bloc
*1.
g.Click OK.
h.Click Status of the card.
i.Set the status to INS.
*1When En-bloc is selected, you need to press # after dialing the phone number. 
						

							5.2 Programming the PBX in the Chicago Office
50 Getting Started