Panasonic Kx Tda5480 Getting Started Manual

Getting Started 61
Appendix B
Alternative Numbering Plan Example 

B1 Extension Number Method
62 Getting Started
B1 Extension Number Method
This section provides a numbering plan example using the extension number method, as 
supplementary information to the PBX code method discussed in 1.2.2 Numbering Plan 
Example.
B1.1 Example Network
The following diagram illustrates a simple VoIP network configured for the extension number 
method.
PSTN(Public Switched 
Telephone Network)
IP Network
Chicago Office
PSTN Trunk (CO Line) Number: 93
VoIP Gateway Trunk (CO Line) Access...

B1 Extension Number Method
Getting Started 63
B1.2 Numbering Plan Example
IP Addressing Information
The following table is a duplication of the table used for the PBX code method.
PBX Numbering Information
The following table contains VoIP Gateway Trunk (CO Line) Access Number, instead of PBX 
Code and TIE Line Access Number as used in the PBX code method.Los Angeles 
OfficeChicago 
OfficeDescription
Card IP 
Address 200.45.11.35 199.176.64.41Identifies the location of each VoIP Gateway 
Card in the...

B1 Extension Number Method
64 Getting Started
Dialing Examples
With the extension number method, the caller dials only the destination number of the called 
party to call through PBXs at different locations.
Calling from Los Angeles to Chicago
To extension 301 via VoIP network
To local telephone 123-4567 via VoIP network through local PSTN
Calling from Chicago to Los Angeles
To extension 201 via VoIP network
To local telephone 456-7890 via VoIP network through local PSTN
PBX Connection Information
Los...

B2 Programming for the Extension Number Method
Getting Started 65
B2 Programming for the Extension Number 
Method
When programming the VoIP Gateway Cards and PBXs for use in a network configured for the 
extension number method instead of the PBX code method, some of the steps in the 
programming procedures require different setting values.
The following two sections provide specific steps that require different setting values. The steps 
other than those provided here have common setting values, and are...

B2 Programming for the Extension Number Method
66 Getting Started
Programming the VoIP Gateway Card in the Chicago Office
Create hunt patterns with the setting values shown below, following the procedure in 
Assigning the Hunt Pattern under 4.3 Programming the VoIP Gateway Card in the Chicago 
Office.
B2.2 Programming the PBX
The steps below are provided in substitution for steps 6 and 7 of the procedure detailed in 5.1 
Programming the PBX in the Los Angeles Office and 5.2 Programming the PBX in the...

B2 Programming for the Extension Number Method
Getting Started 67
Step 7
Assign the leading number used to reach the extensions of the remote PBX:
In the Other PBX Extension Number (TIE) box (01 and 02), type 3 (for the Chicago office 
extensions) and 6 (for the Chicago office fax extensions).
Step 8
Assign the routing information to route calls to the remote PBX:
In the Leading Number box, type 3 (for the Chicago office extensions), 6 (for the Chicago 
office fax extensions), and 93 (for Chicago office...

B2 Programming for the Extension Number Method
68 Getting Started
Programming the PBX in the Chicago Office
Step 6
Assign the PSTN trunk (CO Line) access number:
In the Idle Line Access (Local Access) box, type 93 (for Chicago office PSTN access).
Step 7
Assign the leading number used to reach the extensions of the remote PBX:
In the Other PBX Extension Number (TIE) box (01 and 02), type 2 (for the Los Angeles office 
extensions) and 5 (for the Los Angeles office fax extensions).
Step 8
Assign the...

Getting Started 69
Appendix C
Initialization of the VoIP Gateway Card 

C1 Initializing the VoIP Gateway Card
70 Getting Started
C1 Initializing the VoIP Gateway Card
In case you have forgotten, for example, the IP address or log-in password you set to the VoIP 
Gateway Card, follow the procedure below to return the settings of the card to the factory 
default.
Note
Resetting the card will restore all settings, not just the IP address and log-in password, to 
the factory default.
KX-TDA5480
1.Install the card to the KX-TDA50 PBX, and then turn on the power to the PBX....