Panasonic Kx Tda5480 Getting Started Manual

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
Getting Started 31
4.2.2 Changing the Status of the VoIP Gateway Card
When programming the VoIP Gateway Card, place the card in the STOP status.
1.Click 2.1 Change RUN/STOP status in the 
main menu.
2.
a.Click STOP for Status after changing.
b.Click OK.
3.Click OK.
4.Click OK. 

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
32 Getting Started
4.2.3 Assigning the IP Address
When programming the VoIP Gateway Card for the first time, a new IP address must be 
assigned. Once this is done and the card is on-line, it will be able to communicate with the other 
cards over the VoIP network.
The specific setting values are based on the table under IP Addressing Information in 1.2.2 
Numbering Plan Example.
Note
For more details about IP address assignment, refer to...

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
Getting Started 33
4.2.4 Assigning the Hunt Pattern
The hunt pattern determines how to route incoming calls through the VoIP Gateway Card to 
the PBX.
Note
For more details about hunt pattern assignment, refer to 2.2.5 Hunt Pattern Parameters 
of the VoIP Gateway Card Programming Guide.1.Click 1.5 Hunt Pattern (for Incoming Calls) 
in the main menu.
2.
a.In the Hunt Pattern No. box, type 1.
A hunt pattern will be created with this...

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
34 Getting Started
4.2.5 Programming the Address Translation Table
The function of an address translation table in a VoIP network is to provide two-way translation 
of telephone numbers and IP addresses
*1. The address translation table is owned jointly by all 
VoIP Gateway Cards in the network. Therefore, whenever the address translation table is 
changed, it is important to update all the cards in the network with the latest information;...

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
Getting Started 35
3.Do the following to configure the gateway 
entry for the Los Angeles office:
a.In the GW No. box, type 0.
A gateway entry for the card will be 
created with this numbering.
b.In the Comment box, type Los Angeles 
(a unique identifier of the card in the VoIP 
network).
c.In the IP Address box, type 
200.45.11.35.
d.In the Group No. box, type 0.
Note
Having the value 0 for Group No. means 
that the card does not belong to...

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
36 Getting Started
Note
For more details about address translation programming, refer to 2.2.6 Address 
Translation Table—GW Entry and 2.2.7 Address Translation Table—DN2IP Entry of the 
VoIP Gateway Card Programming Guide.6.Click PREVIOUS.
7.Click 1.6.2 DN2IP Entry.
8.Do the following to configure the Los Angeles 
extensions:
a.In the Leading Number box, type 352 
(PBX code [35] + extension starting digit 
[2]).
b.In the Remaining Number of...

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
Getting Started 37
4.2.6 Downloading the Address Translation Table from the 
VoIP Gateway Card
After the address translation table has been fully programmed, download the data from the 
VoIP Gateway Card.
The downloaded data can be uploaded to the other cards on the VoIP network (see Uploading 
Address Translation Table to the VoIP Gateway Card in 4.3 Programming the VoIP Gateway 
Card in the Chicago Office), so that all the cards can...

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
38 Getting Started
4.2.7 Rebooting the VoIP Gateway Card
For all the changes to the parameters to become effective, you must reboot the VoIP Gateway 
Card.
1.Click REBOOT in the main menu.
2.Click REBOOT. 

4.2 Programming the VoIP Gateway Card in the Los Angeles Office
Getting Started 39
4.2.8 Confirming the IP Address Assignment
After programming of the VoIP Gateway Card is finished, try to access the card with the new 
IP addressing information. If you can connect to the card without problems, the card can be 
placed on the LAN for VoIP operations (see 2.2.2 Connection to the LAN or 3.2.2 Connection 
to the LAN).
Follow the procedure below, referring to 4.1.1 Preparing the PC and 4.2.1 Star ting the IP-...

4.3 Programming the VoIP Gateway Card in the Chicago Office
40 Getting Started
4.3 Programming the VoIP Gateway Card in the 
Chicago Office
This section details the procedure to program the VoIP Gateway Card in the Chicago office, 
which for the most part is a duplication of that for the Los Angeles office. For general 
information that is not discussed here, refer to the relevant sections in 4.2 Programming the 
VoIP Gateway Card in the Los Angeles Office.
There are differences in the procedure where...