Panasonic Kx Taw848 Installation Manual

							2.7 Connection of 2.4 GHz Portable Stations
Installation Manual 81
2.7.5 Site Survey
The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS. After installing the 
CSs temporarily, set the PS to Radio Signal Test mode and measure each CS coverage area. Then, record 
the results on the map of the installation site.
Testing the Radio Signal Strength
Note
Display prompts for the site survey are only available in English.
1.Enter Radio Signal Test mode.
Using the KX-TD7680
Using the KX-TD7690
Notes
*1: CS number and radio signal strength level.
*2: Scan data (test result) number. Empty memory space will be indicated by a number; stored memory 
space will be indicated by a -.
Display example:
Press 1, 9, and POWER
for more than 2 seconds.
 >CS NO.1 LEVEL:12*1
SAVE:0123456789*21 to 9
CS No.199
0 to 9
Scan Data No.
To store the scan data
0
Display example:
Press 1, 9, and POWER
for more than 2 seconds.
 >CS NO.1 LEVEL:12*1
SAVE:0123456789*21 to 9
CS No.199
0 to 9
Scan Data No.
To store the scan data
0 
						

							2.7 Connection of 2.4 GHz Portable Stations
82 Installation Manual
2.Measure the radio signal strength by moving towards and away from the CS.
a.Move to the CS until the radio signal strength level becomes 12.
b.Move away from the CS and identify the CS coverage area within which the radio signal strength 
level is greater than 8. Draw the area on the map.
c.Move away from the CS and identify the CS coverage area within which the radio signal strength 
level is greater than 3. Draw the area on the map.
3.Repeat steps 1 and 2 for other CSs, and relocate the CSs when necessary.
a.Overlap adjacent CS coverage areas where the radio signal strength level is 8 by 5 to 10 meters 
(16 to 33 feet).
CS no. 1PS
PS
PSCS NO.1 LEVEL: 3
CS NO.1 LEVEL: 12
Radio Signal Strength Levels
CS NO.1 LEVEL: 8
Out of range
Receives noise easily or disconnects
May receive noise
Good
Better Level: 00
Level: 01 to 02
Level: 03 to 07
Level: 08 to 10 
Level: 11 to 12
5 m to 10 m
(16 ft to 33 ft)
CS no. 1 CS no. 2 
						

							2.7 Connection of 2.4 GHz Portable Stations
Installation Manual 83
b.Overlap the CS coverage areas of at least 2 CSs at any location in the installation site.
c.Make sure that the radio signal strength level is greater than 3 at any location in the service area 
required by the user.
Referring to the Stored Scan Data
Using the KX-TD7680
Using the KX-TD7690
CS no. 1 CS no. 2
CS no. 3
CS no. 4
Press 1, 9, and POWER
for more than 2 seconds.0 to 9
Scan Data No.191
Display example:
When there is scan data
When there is no scan data
NO.1
CS No.2 LEVEL: 9
NO.0
NOT SAVED
To the Desired Scan Data No.
Press 1, 9, and POWER
for more than 2 seconds.0 to 9
Scan Data No.191
Display example:
When there is scan data
When there is no scan data
NO.1
CS No.2 LEVEL: 9
NO.0
NOT SAVED
To the Desired Scan Data No. 
						

							2.7 Connection of 2.4 GHz Portable Stations
84 Installation Manual
Deleting the Stored Scan Data
Using the KX-TD7680
Using the KX-TD7690
Press 1, 9, and POWER
for more than 2 seconds.0 to 9, or # for all data
Scan Data No.19
To the Desired Scan Data No.
2
Press 1, 9, and POWER
for more than 2 seconds.0 to 9, or # for all data
Scan Data No.19
To the Desired Scan Data No.
2 
						

							2.7 Connection of 2.4 GHz Portable Stations
Installation Manual 85
2.7.6 After Site Survey
After obtaining the proper measurement results, exit Radio Signal Test mode before connecting the CS to 
the PBX.
1.Keep pressing the POWER button on the PS until the PS is turned OFF.
2.Disconnect the AC adaptor or battery box from the CS and stop supplying electricity.
3.Switch all DIP switches on the CS from ON to OFF.
1
2
3
4
5
6
OFF ON 
						

							2.7 Connection of 2.4 GHz Portable Stations
86 Installation Manual
2.7.7 Connecting a Cell Station to the PBX
Refer to the following example to connect a CS to the PBX.
Accessories and User-supplied Items for the CS
Accessories (included): Screws × 2, Washers × 2
User-supplied (not included): RJ11 connector
Note
For details about HLC4 card, refer to 2.4.1 HLC4 Card (KX-TAW84870). 
A Hybrid Port or HLC4 card (RJ11)
CS (RJ11) Cable Maximum Distance
26 AWG: 222 m (728 ft)
24 AWG: 347 m (1138 ft)
22 AWG: 500 m (1640 ft)
CAT 5: 347 m (1138 ft)
Signal NameSignal Name
Pin No.
1
2
3
4
D1
D2D1
D2 Pin No.
1
2
3
4 Hybrid Port 
						

							2.7 Connection of 2.4 GHz Portable Stations
Installation Manual 87
Connecting the CS
1.Connect the cable from a Hybrid Port or the HLC4card to the CS.
2.Pass the cable through the groove of the CS (in any direction depending on your preference).
Modular
To a Hybrid Port,
or HLC4 card
To a Hybrid Port,
or HLC4 card
TO MAIN UNIT
/ PABX 
						

							2.7 Connection of 2.4 GHz Portable Stations
88 Installation Manual
Registering the PS
The PS must be registered to the PBX before it can be used. Programming of both the PS and PBX is 
required. An APT with multiline display (e.g., KX-T7735) is required to perform the PBX system 
programming.
Note
For details about system programming using an APT, refer to 1.13.15 PT Programming in the Feature 
Manual and 2.1 PT Programming in the PT Programming Manual.
Entering the System Programming Mode
APT (Administrator Level)
PS (Using the KX-TD7680)
PS (Using the KX-TD7690)
Note
 means default value throughout this section.
#
= 1234
System Password for Administrator—
for PT ProgrammingProgramming No.
3 digits
PROGRAM/
PAUSE
System Setting Menu
Select 
SYSTEM SET.Press POWER 
for 2 seconds.Select
PS PROGRAM.
4 digits
System Lock Password
If required
FUNC
System Setting Menu
Select 
SYSTEM SETTING.Press POWER 
for 2 seconds.S1S1
MENUSEL
S1
SEL
Select
PS PROGRAM.
4 digits
System Lock Password
If requiredENTR
S1 
						

							2.7 Connection of 2.4 GHz Portable Stations
Installation Manual 89
PS Registration
When the PS has not been registered yet
When registering the PS for the first time, it is possible to select the desired language for the display. 
(You do not need to enter the PS system programming mode when registering for the first time.)
Using the KX-TD7680
Using the KX-TD7690
When the PS has already been registered to another PBX
One PS can be registered to a maximum of 4 different PBXs.
Using the KX-TD7680
Using the KX-TD7690
Setting the System Lock
When a system lock has been set, the system lock password will be required for PS system setting.
Using the KX-TD7680
[690]
001 to 028
PS No.
1 to 4 digits
To the PS
operation
belowExtn. No.
STORESTOREEND
Press
POWER for
2 seconds.Press S3 
for 2 
seconds.C.TonePress S2 repeatedly 
to select the desired 
language.
[ F2 ][ F3 ]
Press
POWER for
2 seconds.Press S3 
for 2 
seconds.C.TonePress S2 repeatedly
to select the desired
language.
F2F3
Choose 
SYSTEM 1–4. Select 
REGISTRATION.C.Tone
Choose 
SYSTEM 1–4. Select 
REGISTRATION.S1 S1
SELSEL
C.Tone
Choose 
Enable/Disable.Select 
SYSTEM LOCK.
C.Tone
4 digits
4 digits ENABLEDISABLE
System Lock PasswordSystem Lock Password 
						

							2.7 Connection of 2.4 GHz Portable Stations
90 Installation Manual
Using the KX-TD7690
Setting the Personal Identification Number (PIN) for PS Registration
To prevent registering the PS to a wrong PBX, a PIN for PS registration can be set to the PBX. Before 
registering the PS to the PBX, enter the PIN set to the PBX into the PS. By doing so, the PS will only be 
registered to the PBX with the matching PIN. 
Notes
 By default, the PIN for PS registration is 1234 for both the PBX and PS. Therefore, the PS can 
be registered to the PBX without setting the PIN.
 The PIN for PS registration will only be used when registering the PS to the PBX. Therefore, during 
normal operation after registration, even if there is more than 1 PBX with the same PIN near the 
PS, the PS will not be inadvertently linked to a different PBX.
Setting the PIN for PBX
Setting the PIN for PS
Using the KX-TD7680
Using the KX-TD7690
S1Choose 
Enable/Disable.
SEL
ENTR
S1
S1
S1 S1
CHNG
SEL
ENTR
Select 
SYSTEM LOCK.
C.Tone
4 digits
4 digits ENABLEDISABLE
System Lock Password
System Lock Password
[692]
4 digits
PIN for PS Registration
1234STORESTORE
END
Select 
CHANGE PINC.Tone1 to 4 digits
1234
PIN for PS Registration
Select 
CHANGE PINS1
ENTR
S1
SEL
C.Tone1 to 4 digits
1234
PIN for PS Registration