Panasonic Indoor Pan Tilt Head Aw Ph405n Operating Instructions

1

 Concerning the balance of the installed unit
The weight balance may be impaired when the pan-tilt head is used in combination with a camer\
a and long lens.  
Follow steps  to  below to check the balance, and then mount the camera. If, after this, the balance is still impaired and 
operations cannot be performed smoothly, it means that the balance must be adjusted. Consult your dealer.
Installation
How to obtain the balance
  Check the center of gravity position with the camera and lens set...



Installation
  Bearing in mind the length of the lens, set the movement range of the pan-tilt head using the limiters in such a way that the 
hood at the edge of the lens will not come into contact with the surface on which the pan-tilt head is installed when the pan-tilt 
head is tilted.
Lens must not come into contact with mounting surface.
   
   
To point the lens any further straight down in a 
stand-alone installation, insert a spacer between  
the pan-tilt head and mounting surface...



Installation
   Attaching the wire
 [Multi-purpose camera AK-HC1500G]
The camera comes with a wire for preventing the camera from dropping. Follow the instructions below to use it to couple the 
camera to the pan-tilt head.
   Use the wire mounting screw (M48 mm with flat washer and spring washer) to attach one end of the wire to the pan-tilt 
head’s arm.
   Use the wire mounting screw (Inch screw with flat washer and spring washer) to attach the other end of the wire on the top 
panel...

4

Connections
 Turn off the power of all the equipment before proceeding with the connections.
 Connect the AC power cable supplied with the AW-PH405 for the AW-PH405 indoor pan-tilt head.
  Use 10BASE-T straight cables to connect the RP connectors on the pan-tilt heads with the CONTROL OUT TO PAN/TILT 
HEAD (1 to 5) connectors on the AW-RP655 multi-function controller and AW-RP555 multi hybrid control panel. The maximum 
extension distance is 81 ft (1000 meters) when using UTP...

5

Connections
For the AK-HC1500G
 Use the connecting cables below to connect the pan-tilt head and camera.AW-CA15H9G
 Refer to the operating instructions for using the connecting cable to ensure that it is connected properly.
Motorized zoom lensIris control cable
Monitor
Camera cable AW-CA15H29G
Zoom/focus control cable
AW-PH405 Indoor Pan-tilt Head
Pan-tilt head/camera control signals
AW-RP655 Multi-function controllerAW-PS505A AC adapter
AW-RP555 Multi Hybrid Control Panel
AW-PS505A AC...

6

Cable specifications
When connecting a Fujinon extender change unit
SHELL
CVCC (12 V)
CGND
EXT Return
EXT Signal
ND Return
ND Signal
CanonEXT ()
CanonEXT ()
GND
GND
Connector:  HR10A-10P-10P (73) made by Hirose Electric
SHELL
Connect this connector to the ND/EXT connector on the pan-tilt head
Connect this connector to the EXT connector on the lens
When connecting a Canon lens with motorized extender unit
  For details on how to connect the extender change unit to the lens, consult the...

7

Replacing the consumable parts
 Replacing the motor
Replace the motor when it ceases to operate properly.
For details on the motor replacement, consult your dealer.
  Replacing the belt
Replace the belt when the preset stop accuracy has deteriorated.
For details on the belt replacement, consult your dealer.
  Replacing the gear
Replace the gear when the preset stop accuracy has deteriorated.
For details on the gear replacement, consult your dealer.
The motor, gear and belt are consumables....

8

Appearance
Unit: inch (mm)
5-/8 (17) 7-/16 (18)
1-9/16
 (19)
6-1/
 (165)
8-1/4 (09)
16-/8
 (416)
6-5/8 (168)
ø6-5/16 (160)
1-5/8
 
(4)
ø5-/4 (146)
ø6-5/16 (160)
ø5-/4
 (146)
4-M6 screws

1-7/8
 
(47)
ø6-5/16 (160)
-1/16 (71) -1/16 (97) 

9

Specifications
Genlock input:   
BNC 
Black burst or composite video signal, Tri Sync
Prompter input 
  (PROMPTER IN):   
BNC
 
Through output to PROMPTER connector
Prompter output 
  (PROMPTER OUT):  D-SUB 15-pin
Camera video output
 VIDEO:   BNC, 75-ohm output
  Y:  BNC, 75-ohm output
  Pr/C:   BNC, 75-ohm output
  Pb:  BNC, 75-ohm output
  SDI:   BNC
  AUX:   BNC
Camera, pan-tilt head control:  RJ45, RS-4, pan-tilt head control signal output
  RP    Connecting cable: 10BASE-T...

0

Memo
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — 
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — 
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — 
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — 
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — —\
 — — — — — — — — — — — — — — 
 — — — — — — — — — — — —...