Panasonic Indoor Pan Tilt Head Aw Ph405n Operating Instructions

11

Installation
For a stand-alone installation
 Assembling the pan-tilt head
When assembling the pan-tilt head, use the Allen key (provided) and screwdriver, and secure the head by tightening the screws 
firmly. After mounting the pan-tilt head, check there is no play in its installation.
  Attaching the camera mounting base
Attach the camera mounting base to the rotary arm using the three mounting screws (M5  mm, with flat washers, spring 
washers) provided. The installation direction...

1

Installation
 Mounting the tally lamp
Connect the cable connector which is taped to the top of the pan-tilt head to the tally\
 cable connector.
Mount the tally lamp on the top of the pan-tilt head using the two screws provided.
Mount the lamp while paying attention to the wire.
 
The cable for the tally cable connector is about -1/16” (50 mm) long.
When connecting the cable to the connector, do not pull it out beyond this length. 
 
If the tally lamp is not going to be used, insert the...

1

Installation
 Concerning the safety modes
This unit comes with two safety modes which are designed to safeguard the user and others from injury and to prevent damage 
to the pan-tilt head.
1. Mode for ensuring safety in the case of collisions
When the rotary arm of the pan-tilt head or some other unit installed on the head keeps colliding with an obstruction or a 
person (approx. 6 seconds when the head rotates at 45 degrees per second), the mode for ensuring safety in the case of 
collisions...

14

Installation
 Procedure for changing the settings of the CPU circuit board switches
Follow the steps below to change the settings of the CPU circuit board switches.
  Remove the four screws, and gently remove the housing case.
  Disconnect the tally cable connector.
   Set the switches on the CPU circuit board.  
After you have performed the settings, connect the tally cable connector, and then return the housing case to its original 
position, and attach it using the screws. (Take care to...

15

Installation
 Setting the CPU circuit board switches
  Setting SW1
These switches are used to set the operations of the AW-PH405. Before changing their settings, make sure that the power 
has been turned off.
No.1:    Auto focus (AF)/extender (EXT) selector switch.  Use this at the ON position when using an auto focus lens which is connected to the LENS I/F (1) connector; use it 
at the OFF position when using a lens with a motorized extender connected to the ND/EXT connector.No.2:    Diagonal...

16

Installation
 Pan-tilt head mounting conditions
Pan-tilt head weightMounting specificationsCompatible camerasCamera weight
Camera anti-drop measures
Compatible lensesLens weightCable weightTotal weight
Approx.  lbs (10 kg)
Stand-alone installation or installation on the celling
Convertible camera series 
AW-E50 AW-E650 AW-E655 AW-E750 AW-E860
Approx.  
.6 lbs 
(1. kg) 
max.Wire provided used for mounting
AW-LZ16MD55P 
AW-LZ16MD7P AW-LZ17MD9AG Approx. .9 lbs...

17

Installation
Note  
When installing the pan-tilt head, do not forcibly turn the rotary head or rotary arm 
manually. Doing so may result in malfunctioning.
For a stand-alone installationFor installation on the ceiling 

18

   Mounting the camera
 [Convertible camera AW-E350/E650/E655/E750/E860]
When mounting the camera, take sufficient care to ensure that the camera will not come off or fall down.
   Mount the lens onto the convertible camera.  
(Before mounting a large lens, consult with your dealer.)
   Mount the convertible camera after aligning it with the guide pins.  
Use a tool to tighten up the mounting screws so that they are securely tightened.

CameraLens
AW-E50AW-LZ16MD55P
AW-LZ10MD6
AW-E650...

19

Installation
   Attaching the wire
 [Convertible camera AW-E350/E650/E655/E750/E860]
The camera comes with a wire for preventing the camera from dropping. Follow the instructions below to use it to couple the 
camera to the pan-tilt head.
When mounting the cameras with fan (AW-E655, AW-E750, AW-E860)
   Use the wire mounting screw (M48 mm with flat washer and spring washer) to attach one end of the wire to the pan-tilt 
head’s arm.
 Mount the mounting spacer on the top panel of the camera. (The...

0

Installation
   Mounting the camera
 [Multi-purpose camera AK-HC1500G]
When mounting the camera, take sufficient care to ensure that the camera will not come off or fall down.
   Mount the lens onto the multi-purpose camera. 
(1)   Lenses that can be used
 
• Use any of the portable lenses which are listed below.
Fujinon HA18, HA1, HA series
CanonHJ17e, HJ1e series
  (2)   Lenses that cannot be used
 
•   Do not use the large-sized lenses [with a weight of 11 lbs (5 kg) or...