Home
>
Panasonic
>
Chair/Seating
>
Panasonic Household Massage Lounger Ep1080 Operating Instructions
Panasonic Household Massage Lounger Ep1080 Operating Instructions
Have a look at the manual Panasonic Household Massage Lounger Ep1080 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
10 English 2 POWERING UP THE UNIT See Warning No. 8 on page 1. 1 Make sure the power plug is functional. Make sure the power plug is undamaged. Make sure the power plug is free of foreign matter and debris. 2 Plug the power plug into an electrical outlet. 3 Verify that the lock switch key is turned to the “open” position. If in “lock” position, turn the lock switch key to “open”. 4 Slide the power switch to the “on” position. 3 CHECK THE UNIT 1 3 1 Make sure the covering is free of rips or tears. 2 Make sure there are no obstacles between the parts of the unit. 3 Make sure the massage heads are in the retracted position, i.e. they are parked to the left and right in the upper part of the backrest. If not retracted, press twice to return the massage heads to the retracted position. 4 Make sure the legrest is lowered. Do not sit on the legrest when it is raised. Doing so may cause it to collapse down or bend the legrest. The legrest is not meant to support full body weight. See Warning No. 14 on page 2.• 4 ADJUSTING FOR CORRECT PILLOW HEIGHT Velcroes Adjust the pillow height so that the bottom edge of the pillow is at ear level. If positioned too low, the pillow can lessen the effect of massage around the neck area. • 5 ADJUSTING THE RECLINING ANGLE Press and to adjust the angle of the backrest and legrest. With the button held down, movement will continue until a “beep-beep-beep” sound indicates the backrest has been raised or lowered as far as possible. The legrest will start to move shortly after the backrest. Approx. 80˚ Approx. 0˚ Approx. 120˚ Approx. 170˚ * The reclining operation is a function that adjusts the angle of the backrest and legrest. Avoid using it for any other purposes, such as continuous up/down operation etc. • • • •
11 English Pre-Program and Quick Massage Characteristics Shiatsu Uses mainly Soft Shiatsu, Tap and Knead actions to comfortably loosen and provide relief from tension held at pressure points. Recommended for those with severe stiffness or who prefer a stimulating massage. Swedish Uses mainly Swedish, Hawaiian and Knead actions to evenly apply muscle- relaxing strokes all over. Recommended for those who want a gentle relaxing massage. Chiro Uses Full Roll and Compression to stretch all your muscles. A kneading action is applied to a stiff back and joints to refresh the posture and strengthen you against fatigue. Recommended for those who want a fairly strong massage due to stiff muscles. Quick Covers all areas using a variety of massage actions, all in a span of just five minutes. Recommended for those who want a quick, relaxing massage. 1 2 4 1 Press the OFF/ON button. The OFF/ON indicator will come on. 2 Select the pre-program you want. Please press one of the flashing buttons. If you press another Pre-Program button or a manual operation button during your selected pre-program massage, the massage will switch to the newly selected massage. Pressing a Pre-Program button automatically moves the backrest and legrest into massage position. 3 Sit as far back in the seat as possible with your head centered on the pillow. 4 Adjusting shoulder position When the shoulder position indicator is flashing, adjust the position \ of the massage heads (upper heads) so that they lightly touch the shoulders. Too high Correct position Too low Lightly touching the shoulder. • Up Down Press PressAppr o ximate Height 6.0 ft. (185 cm) 5.2 ft. (160 cm) 4.5 ft. (140 cm) 5-Stage adjustment [up and down approx. 3.9 in. (10 cm)] It is possible to change the position of the massage heads during the massage. When it is not possible to correctly adjust the shoulder position, you may have to slide your body and adjust it again. • • • • • • • • About the Time Indicator Time Remaining Approx. 15 min. Approx. 9 min. Approx. 3 min. Displays remaining massage time via flashing LED. Starts counting down from 15 minutes in increments of approximately 3 minutes. Flashing speeds up one minute before end of massage. • • • USING PRE-PROGRAMS AND QUICK MASSAGE
12 English Persons whose height is less than 4.5 ft. (140 cm) or more than 6.0 ft. (185 cm) are recommended to use the unit in the manner described below when the massage heads do not touch their shoulders.Height is around 4.5 ft. (140 cm) or less Height is around 6.0 ft. (185 cm) or more Use by placing a cushion on the seat and sitting as far back as possible.Use by reclining the backrest and sliding your body downward. 5 Customize A Selecting an area for a focused massage Massaging the Neck and Shoulders Massaging the Lower Back PressThe upper and lower back will also be massaged slightly. •Press The neck and shoulders will also be massaged slightly. • *Press the button again to toggle it off. B Removing tapping from pre-programs Press *Press the button again to restore tapping to the program. 6 Auto shut-off in pre-programs The massage will end after approximately 15 minutes and the unit will automatically shut off. The massage heads will move to the retracted position and stop. The legrest will automatically lower. The OFF/ON indicator will flash until the heads have stopped moving. If you want to continue using the unit, press the OFF/ON button. Please rest at least 10 minutes between massages. • • • • • Stopping a pre-program Immediately stopping the massage PressPress the OFF/ON button. The massage heads will move to the retracted position, and the backrest and legrest will automatically return to their original position. • •Press Press the Quick Stop button. All movement will stop immediately. • •
13 English 2 3 1 Open the cover of the controller. 2 Press the OFF/ON button. The OFF/ON indicator will come on. All of the Manual Operation buttons will start to flash. 3 Select the massage type you want. Press the button of the massage you require. The button will light up and the massage will begin (See Page 14). The unit will automatically recline to the massage position. See Page 10 for a fine adjustment. 4 Customized adjustments You can adjust the position or speed of the massage heads, and you will hear a “beep-beep-beep” sound when it reaches its limit. A Adjusting the Vertical Position of the Massage Heads Up DownPress the button once to move the position slightly [approx. 0.6 in. (15 mm)]. Press and hold the button to move the position continuously; release the button to stop the movement. • B Adjusting the Width between Massage Heads Increasing DecreasingTap, Soft Shiatsu, Full Roll, and Regional Roll can be adjusted in 3 steps. • C Adjusting Massage Speed Increasing Decreasing Massage speed is adjustable in 5 steps. • 5 Auto shut-off in manual operation The massage will end after approximately 15 minutes and the unit will automatically shut off. The massage heads will move to the retracted position and stop. The legrest will automatically lower. The OFF/ON indicator will flash until the heads have stopped moving. If you want to continue using the unit, please press the OFF/ON button. Please rest at least 10 minutes between massages. • • • • • • • • • MANUAL OPERATION FOR THE UPPER BODY Massage Actions Knead Feels like the fingers and thumbs of two hands squeezing in unison as they carefully work their way upwards to loosen stiffness. Recommended for the area of the neck and shoulders. Swedish Feels like a two palms gliding over the skin as they rhythmically knead the muscles beneath. Recommended for loosening up large areas of the back. Soft Shiatsu Feels like a pair of thumbs carefully alternating between the right and left sides as they zero in on their target. Recommended for loosening up knots of tension. Full Roll From lower back to neck, you can f eel it mo ve 26.6 in. (67.5 cm) up and down the whole of the upper body. Recommended for overall stretching of the back muscles. Compression Applies fluent alternating strokes to the left and right sides as if drawing stiffness to the outside. Recommended for relaxation of the whole body. Hawaiian Feels like two hands moving rhythmically in a circular pattern to relax and refresh the back. Recommended for relieving tension in the lower back. Tap Feels like the edges of two hands rhythmically tapping to penetrate into the body and relax muscles. Recommended for use on the fine muscles of the neck or as a finishing massage. Regional Roll You can feel it travel up and do wn w orking on 3.9 in. (10 cm) localized areas of the back. Recommended for focused rolling out of back muscles.
14 English NOTE: A built-in timer prevents overuse of the unit. When using manual operation, the timer automatically stops operation after 15 minutes. *If you want to continue to use the unit, we recommend that you have a break of at least 10 minutes between massages to allow your body to rest. • • Combining Massages It is possible to combine massage types. It is not possible to combine massage types in the same category. • • E.g. 1 Adding Tap when Knead is selected. E.g. 2 Adding Full Roll to the selection. E.g. 3 Deselecting Full Roll. Changing Massage Types E.g. 1 Changing massage types in the same category. (Changing to Hawaiian when Knead is selected.) E.g. 2 Changing to a massage type outside the category. (Changing to Tap when Knead is selected.) • When Knead is combined with T ap, deselecting Knead will leave only Tap. Stopping mid-way through a massage Immediately stopping the massage Press Press the OFF/ON button. The massage heads will move to the retracted position, and the backrest and legrest will automatically return to their original position. • •Press Press the Quick Stop button. All movement will stop immediately. • •
15 English AFTER COMPLETING THE MASSAGE RETURN THE SEAT TO THE ORIGINAL POSITION 1 Check that there is nothing in the vicinity of the backrest or the legrest. 2 Press the OFF/ON button twice. The backrest and legrest will automatically return to their original positions. The backrest and the legrest can be returned with the reclining button. (See Page 10) 3 Place the controller in its holder. 4 Return the pillow and the back cushion to their original positions. • DISCONNECT THE POWER See Warning No. 2 on page 1, No. 2 on page 2, and No. 10 on page 3. 1 Slide the power switch to the “off” position. 2 Turn the lock switch key to the “lock” position. 3 Unplug the power cord. 4 The lock switch key must be stored out of the reach of children. CLEANING AND MAINTENANCE See Danger No. 1 on page 1. LEATHER COVERING ON THE PILLOW, THE BACK CUSHION AND THE UNIT Wipe these areas with a soft, dry cloth. (Do NOT use cloths containing any kind of chemical, etc.) If the leather is particularly dirty, dampen with liquid soap and brush the surface. Wipe with a cloth dampened with water. Allow to dry naturally. (Do NOT use a hair dryer to try to dry the surfaces more quickly.) Wearing of denim, colored, patterned or other clothing with a tendency to fade should be avoided during use, as it could lead to discoloration of the leather. Please do NOT use thinners, benzine or alcohol. PIPE AND PLASTIC AREAS 1 Wipe the unit with a cloth that has been soaked in a mild detergent and then thoroughly wring out. 2 Next wipe the unit with a cloth that has been moistened with just water and thoroughly wring out. *Make sure you thoroughly wring out the cloth first when cleaning the controller. 3 Allow the unit to dry naturally. Please do NOT use thinners, benzine or alcohol. COATED FABRIC 1 Wipe the seat fabric with a cloth that has been soaked in a mild detergent solution and then thoroughly wring out. 2 Use a brush to apply a mild detergent to areas where the coated fabric has become particularly soiled. Be careful not to brush the fabric too much as this may damage it. 3 Next wipe the fabric with a cloth that has been moistened with just water and then thoroughly wring out. 4 Allow the fabric to dry naturally. Please do NOT use thinners, benzine or alcohol. • • • • • •
16 English TROUBLESHOOTING Problem Cause and Remedy Motor NoisesIt sounds and feels like the massage heads are straining to get over wrinkles in the cloth. The motor groans when it comes under load. There is excessive noise during Tapping. (The noise is greater at the top of the unit.) There is a creaking noise when the massage heads are in operation. There is a rattling sound when the massage heads move up or down. The belt can be heard rotating. There is a rubbing sound produced by the massage heads rubbing on the seat fabric. There is a noise when the backrest cushion moves over the armrest when the seat is reclining. There is a noise when I sit down. There is a strange sound when the massage heads move in and out. When the power switch is turned on there is a humming sound. The legrest rattles. • • • • • • • • • • • • These sounds are perfectly normal and will not have any effect on the operation of the unit. The massage heads stop during operation. When excessive force is applied to the massage heads during operation, in the interests of safety the massage heads may stop moving. If all markings and buttons on the controller start to flash, which is extremely unusual, turn off the power switch, wait for approximately 10 seconds and then turn the power switch on again. If the massage heads stop again, position yourself so that your back is not completely in contact with the backrest. The massage heads do not come up to the shoulder or neck. The position of the massage heads is incorrect. (See Page 11) The height of the left and right massage heads is different. An alternating tapping method is employed, which means that this phenomenon will naturally occur. There is nothing wrong with the unit. It is not possible to recline the unit. The legrest cannot be raised or lowered. If the unit encounters an obstacle or if excessive force is exerted on it during operation, in the interests of safety the unit will come to a stop. If all markings and buttons on the controller start to flash, which is extremely unusual, turn off the power switch, wait for approximately 10 seconds and then turn the power switch on again. Rec lining does not take place even though a massage is started in pre-programs. (The seat does not automatically recline.) In some cases the seat may not automatically recline depending on the position (angle) of the b\ ackrest or the legrest. Automatic reclining will not activate when the backrest is reclined to flat position more than massage position and legrest is in upper position. The backrest does not return to the upright position. The backrest will not return to the upright position if the timer is activated or the button is pressed. (Pressing twice will return the backrest to its original position.) (See Page 15) It is not possible to switch from Swedish and Knead to Hawaiian and Compression. Switching can be hindered when the user’s body weight is not resting on the massage heads. Shift your weight so that your body is contact with the massage heads. The legrest will not return to its original position. If the length of the legrest has been extended, the legrest will strike the floor, preventing from returning to its original position. Try again after retracting it to its original length. The unit will not operate at all. The power cord has been disconnected. (See Page 10) The power switch on the unit has not been turned on. (See Page 10) A Pre-Program button or Manual Operation button hasn’t been pressed after pressing . (See Pages 11, 13) • • • The unit has been damaged. Stop using the unit immediately. The power cord or power plug is abnormally hot. Stop using the unit immediately. See Warning No. 5 and 13 on page 3. If service is needed please contact your local dealer or all 1-877 Panafix (723-2349).
No. 1 EN, SP Printed in China P93101080231 Impreso en China Panasonic Consumer Electronics Company One Panasonic Way 1H-1 Secaucus, New Jersey 07094 1-800-338-0552 for questions and comments. www.panasonic.com/massage