Panasonic Home Network Systrem Oudoor Camera Kx Hnc600w Installation Guide

Installation location examples
I want to detect visitors approaching the house
Refer to the table below for detecting visitors at an entrance or gate without detecting cars in the
street.
Ideal examplePoor example
 Approx. 3 m (9.8 feet)
Visitors pass in front of the camera from side
to side, cars in the street are less likely to
cause false detections.Cars in the street are more likely to cause
false detections.
For assistance, please visit www.panasonic.com/support11
Installation Location1 1   

I want to detect people entering the garage
Refer to the table below for detecting people entering a garage without detecting cars in the
street.Ideal examplePoor example
Visitors pass in front of the camera from side
to side, cars in the street are less likely to
cause false detections.
R To prevent faces from being obscured by
tall vehicles, adjust the installation position
and angle of the camera.Cars in the street are more likely to cause
false detections.
12For assistance, please visit...

Do not install in these
locations
Installing in the following areas may
cause deformation, discoloration,
malfunction, or operational failure
R In direct sunlight or directly under an
outdoor light (even if the surroundings are
within operational temperature range, parts
of the product may become hot)
R Areas subject to frequent vibration, shock,
or impact
R Near fire, heating devices, magnetic fields
(such as near magnets), or air conditioners
(including outdoor equipment such as unit
compressors)
R...

RAreas affected by breezes from fans, air
conditioning unit compressors, water
heaters, or car exhaust (severe
temperature variations may cause false
detections)
R Areas with strong winds (wind can shake
the camera and cause false motion
detection)
R Areas with reflective objects, such as glass,
that can interfere with detection of
temperature variation
R Areas where brightness changes easily
(such as areas where shadows form in the
afternoon and lights turn on at night)
R Areas where backlight occurs...

Part names and functions
MicrophoneSensor range cap (Standard)Infrared sensorLED indicatorLens unitSpeakerMN
Used when registering the camera to the
hub.
Safety wireCamera mounting standDC cable
LED indicator
You can use the LED indicator to confirm the
camera’s status.
IndicatorStatusOffNo power, or LED
indicator is turned
off *1Green, litNormal operation *1Green, blinkingRegistration modeRedMotion detection
features were
triggeredIndicatorStatusRed, blinkingLive images are
being viewed or
recordedRed,...

Registering the camera
This procedure is not required for devices
that were included as part of a bundle.
Before you can use the camera, it must be
registered to the hub.
If the camera is not registered to a hub, the
camera’s LED indicator blinks in amber.
You can register each device by using the
registration buttons or the  [Home Network]
app.
Note:
R Before registering the camera, make sure
the AC adaptors of the hub and camera are
connected and each device is powered.
Using registration buttons
1...

Installation
Installation precautions
R Do not install the camera on a ceiling.
R Do not install the camera in areas directly
exposed to water or rain.
R Holes must be made in the wall for cables
and wires to pass through. Panasonic takes
no responsibility for issues related to
opening holes in walls.
R Make sure to waterproof the holes you
make in the wall.
R Make sure you attach the safety wire to
prevent the camera from falling.
R Do not use an impact driver. (This may lead
to damaged screws or...

Ideal example
Structure supports exterior surface
 Siding Structure behind siding
Concrete
R Do not use the included screws. Use screw
anchors (screw ø: 4 mm (5/32 inches))
designed for concrete walls.
R Carefully read the instructions supplied with
the anchors. Follow instructions regarding
drill bit diameter, hole depth, etc.
R Drill a pilot hole. Remove any debris after
drilling the pilot hole.
1 Mark the hole depth on the drill bit (
)
and then drill a pilot hole.
2 Remove debris.
3Insert an anchor,...

Installing the camera
1 Attach the safety wire to the camera.
R Place the ring of the safety wire ( A)
over the screw hole.
R Place a washer ( B) on top of the ring
of the safety wire.
R Tighten the screw ( C) for the safety
wire on top of the washer.
2 Attach the camera mounting stand to an
outdoor wall.
R Secure the stand to the wall by
tightening 4 screws ( A).
R
 37 mm (1 15/32 inches)
Note:
R Use the following template below when
determining the location of the screw
holes.For assistance, please...

3Attach the camera to the stand.
R Loosen the screw ().
R Insert the tip of the stand ( A) into the
stand attachment hole ( B) on the rear
or bottom side.
R Secure the camera by tightening the
screw (
).
Attaching to the hole on the rear side
Attaching to the hole on the bottom
side
4 Adjust the camera angle.
R Loosen the screw ( A), adjust the
camera to the desired angle, and then
tighten the screw ( B) to secure the
camera in place.20For assistance, please visit www.panasonic.com/support
Setup1 2 112
2...