Panasonic Home Network System Water Leak Sensor Kx Hns103 Installation Guide

Installation Guide
Home Network System
Water Leak Sensor
Model No.    KX-HNS103 Thank you for purchasing a Panasonic product.
This document explains how to install the water leak sensor properly.
For details about how to use the system, refer to the User’s Guide
(page 18). Please read this document before using the unit and save it for future
reference. For assistance, please contact us at 1-800-272-7033 or visit
our Web 
site: www.panasonic.com/support  for 
customers in the U.S.A.
or Puerto Rico....

Introduction
Accessory information 
...............3
Important Information
About this system ......................4
For your safety ........................... 4
Important safety instructions ...... 5
For best performance 
................5
Other information .......................6
Setup
Part names and functions  ..........8
LED indicator  .............................8
Setup overview  ..........................8
Inserting the battery ...................9
Registering the sensor ...............9...

Accessory information
Supplied accessories
No. Accessory item/Part number Quantity
A Battery *1
1
B Wa
ll mounting adaptors *2
2
C Wa

ll mounting screws (25 mm (1 inch)) *3
/X
 TB4+25AVW3*1 When replacing the battery, see “Power source” of “Specifications”, page 19
for

 battery information.
*2 1 adaptor for the main unit: PNHR2107Z 1 adaptor for the probe unit: PNHR2108Z
*3 2 screws for the main unit and 1 screw for the probe unit
A B C
Other information
R
D
es

ign and specifications are subject to...

About this system
R
Thi
s system is an auxiliary system; it
is not designed to provide complete
protection from property loss.
Panasonic will not be held
responsible in the event that
property loss occurs while this
system is in operation.
R The system’s wireless features are
subject to interference, therefore
functionality in all situations cannot
be guaranteed. Panasonic will not
be held responsible for injury or
damage to property that occurs in
the event of wireless communication
error or failure....

R
Do not touch the terminals   and
 with metal objects.
R Ris
k of explosion if battery is
replaced by an incorrect type.
Dispose of used battery according to
local regulations.
R If any electrolyte should come into
contact with your hands or clothes,
wash it off thoroughly with water.
R If any electrolyte should come into
contact with your eyes, never rub
your eyes. Rinse your eyes
thoroughly with water, and then
consult a doctor. CAUTION
CR Lithium battery
R
Use

 only the battery noted on
page 3.
R...

antennas of mobile phone cell
st
a
tions. (Avoid putting the hub
on a bay window or near a
window.)
R If the reception for a hub location is
not satisfactory, move the hub to
another location for better reception. Environment
R
Kee

p the product away from
electrical noise generating devices,
such as fluorescent lamps and
motors.
R The product should be kept free
from excessive smoke, dust, high
temperature, and vibration.
R The product should not be exposed
to direct sunlight.
R Do not place heavy...

Note for the battery removal
pro
cedure
Refer to “Inserting the battery” on
page 9. Notice
For assistance, please visit www.panasonic.com/support
7Important Information
)/4@	FO@FO
@@WFSQEG





  

Part names and
fun
ctions Main unit
Main unit cover
M N
Us e

d to confirm the status of the
sensor or register the sensor to
the hub. LED indicator
Cable
Probe unit
Probes
LED indicator
Yo
u

 can press  M N
 and check the
L E

D indicator to confirm the sensor’s
status.
After confirming the sensor’s status, we
recommend turning the LED indicator off by pressing 
M N
 again as soon
a s

 possible, otherwise battery life may
be reduced. Indicator Status
Green, lit No water detected
Red, lit Water...

Inserting the battery
R
USE
 ONLY a CR2 Lithium battery.
R Confirm the polarities ( ,  ).
1 Rem

ove the main unit cover.
R Lift from the indented area ( A)
and open the main unit cover
( B ). 2
Insert the battery. 3
Attach the main unit cover. Registering the
sen

sor
This procedure is not required for
de v

ices that were included as part of
a bundle. Before you can use the sensor, it must
be 

registered to the hub.
If you purchased devices separately
(i.e., not as part of a bundle), you must
register...

group them by location. For more
in
f
ormation, refer to the User’s Guide
(page 18). Confirming the
us
a

ge area Wireless communication
ra
n

ge
The wireless communication range of
each device in the system from the hub
is approximately 50 m (160 feet)
indoors and approximately 300 m
(1,000 feet) outdoors. Wireless
communication may be unreliable
when the following obstacles are
located between the hub and other
devices.
R Metal doors or screens
R Walls containing aluminum-sheet
insulation
R Walls made...