Panasonic Home Network System Indoor Camera Kx Hnc200 Installation Guide

							Wall mounting
R
Mo u
nt the camera on the stable location
where the unit can be adequately
supported when installing.
R The AC adaptor should be connected to a
vertically oriented or floor-mounted AC
outlet. Do not connect the AC adaptor to a
ceiling-mounted AC outlet, as the weight of
the adaptor may cause it to become
disconnected.
R Do not mount the camera on a soft
material. It may fall down, break or cause
injury.
R Do not mount the camera on the following
places: plaster board, ALC (autoclaved
lightweight cellular concrete), concrete
block, plywood less than 25 mm (1 inch)
thick, and etc.
1 Drive the screws (not supplied) into the
wall.  Longer than 20 mm (25/32 inches)
 Space 1.3 mm (1/32 inches)
Note:
R
U
se

 the following template when
determining the location of the screw
holes. 2
Mount the camera to the wall.  Screws
 28 mm (1 3/32 inches)
3
Adjust the angle of the camera. For assistance, please visit http://shop.panasonic.com/support
11 Setup
HNC200_(en_en)_1005_ver.210.pdf   112015/10/06   13:23:031 2 12 (1 3/32 inches)28 mm 1 2 2
1   
						

							Testing the motion
de
t
ection range
After you have installed the  [Home Network]
app on your mobile device, you can use your
mobile device to test the performance of the
camera’s motion detection feature. For more
information, refer to the User’s Guide
(page 13).
1 Start the  [Home Network]  app and
display live images from the camera.
2 Move to an area within the camera’s
viewable area.
3 While moving near the camera, use your
mobile device to observe where you are
in the viewable area when the camera’s
motion detection feature is triggered.
RWhen the motion detection feature is
triggered, the camera’s LED indicator
lights in red for about 3 seconds.
4 Note the areas of the viewable area
where movement is detected, and make
adjustments as necessary.
Note:
R You can adjust the area detectable by the
visual sensor. For more information, refer to
the User’s Guide (page 13). Testing the microphone
To
 

test the microphone, speak loudly and
clearly into the microphone while a mobile
device user is viewing live images from the
camera. Features available when
us
i

ng the [Home Network]
app
Some of the features that are available when
using the  [Home Network]  app are listed
below. For more information, refer to the
User’s Guide (page 13).
– Alarm system
You can use the app to arm and disarm the
alarm system, confirm the current status of
the sensor, and view a log of previous
events.
– Live camera monitoring
You can view live images from the camera,
even while away from home.
– Listen and talk
You can use your mobile device to talk and
listen to anyone within range of the
camera’s microphone and speaker.
– Sensor adjustment
You can adjust the detection range of the
visual sensor and the setting levels of the
sound sensor and temperature sensor.
– Sensor integration
You can configure the camera’s sensor
features to trigger other system events,
such as camera recording *1
, turning on an
electric device (such as a lamp), etc.
(Appropriate device required.)
*1 A commercially-available microSD card must be inserted into the hub in
order to record images.
– Notification
You can configure the camera to send a
notification to the  [Home Network] app
when the camera’s sensor features are
triggered, for example, when motion is
detected, if a baby is crying (sound sensor)
or if the room becomes too warm or too
cold (temperature sensor).
12 For assistance, please visit http://shop.panasonic.com/supportAppendix
HNC200_(en_en)_1005_ver.210.pdf   122015/10/06   13:23:03 
						

							Accessing th
e  User’s Guide
The User’s Guide is a collection of online
documentation that helps you get the most out
of the  [Home Network]  app.
1 iPhone ®
/iPad ®
Tap   in the app’s home screen.
An d

roid™ devices
Tap   or press your mobile device’s
men

u button in the app’s home screen.
2 Tap [User’s Guide] .
Note:
R Microsoft ®
 Windows ®
 Internet Explorer ®
 8
and earlier versions are not supported.
R Android 4.1 or later versions are
recommended.
R You can also access the User’s Guide at
the web page listed below. www.panasonic.net/pcc/support/tel/
ho
m

enetwork/manual/ Specifications
R
Sta

ndards
DECT (Digital Enhanced Cordless
Telecommunications)
R Frequency range
DECT: 1.92 GHz – 1.93 GHz
R RF transmission power
DECT: 115 mW (max.)
R Power source
120 V AC, 60 Hz
R Power consumption
Standby: 2.2 W
During operation:
3.0 W (when the LED lights are not lit)
4.0 W (when the LED lights are lit)
R Operating conditions
0 °C – 40 °C (32 °F – 104 °F)
up to 90 % relative humidity
(non-condensing)
R Transmitting range
Approx. 50 m (160 feet) indoors
Approx. 300 m (1,000 feet) outdoors
R Image sensor
0.3 megapixel CMOS
R Minimum illuminance required
0 lx *1
R Focal length
Fixed (0.4 m (1.3 feet) – infinity)
R Angular field of view (camera angle)
Horizontal: approx. 70°
Vertical: approx. 50°
R Motion detection method
Visual sensor
R Motion detection range
Horizontal: approx. 70°
Vertical: approx. 50°
R Adjustable mounting angles
Horizontal: ±90°
Vertical: facing forward - facing down
approx. 60°
(adjustable when mounting)
R Dimensions (height  ´ width  ´ depth)
Approx. 102 mm  ´ 75 mm  ´ 75 mm
(4 inches  ´ 2 15/16 inches  ´ 2 15/16 inches)
R Mass (weight)
Approx. 160  g (0.35 lb)
*1 The infrared LEDs that surround the camera lens will illuminate in low-light
conditions.
For assistance, please visit http://shop.panasonic.com/support 13 Appendix
HNC200_(en_en)_1005_ver.210.pdf   132015/10/06   13:23:03    
						

							FCC and other information
Th
i
s device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept
any interference received, including
interference that may cause undesired
operation.
Privacy of communications may not be
ensured when using this device.
CAUTION:
Any changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate this device.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/ TV technician for help.
Some devices operate at frequencies that may
cause interference to nearby TVs and VCRs.
To minimize or prevent such interference, this
device should not be placed near or on top of a TV or VCR. If interference is experienced,
mo
v

e this device further away from the TV or
VCR. This will often reduce or eliminate
interference.
FCC RF Exposure Warning:
R This product complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.
R To comply with FCC RF exposure
requirements, the device must be installed
and operated 20 cm (8 inches) or more
between the product and all person’s body.
R This product may not be collocated or
operated in conjunction with any other
antenna or transmitter.
R For body-worn operation, the device must
be used only with a non-metallic accessory.
Use of other accessories may not ensure
compliance with FCC RF exposure
requirements.
Notice:
R FCC ID can be found on the rear of the unit.
14 For assistance, please visit http://shop.panasonic.com/supportAppendix
HNC200_(en_en)_1005_ver.210.pdf   142015/10/06   13:23:03 
						

							Customer services
For assistance, please visit http://shop.panasonic.com/support
15 AppendixHNC200_(en_en)_1005_ver.210.pdf   152015/10/06   13:23:03You may also contact us directly at: 1-800-272-7033,Monday - Friday 9 am to 9 pm;  
Saturday - Sunday 10 am to 7 pm, EST. Accessories!
http://shop.panasonic.com/support
Customer Services Directory Shop
for all your Panasonic gear
Go to 
Get everything you need to get the most out of your Panasonic products 
Accessories & Parts for your Camera, Phone, A/V 
products, TV, Computers & Networking, Personal 
Care, Home Appliances, Headphones, Ba!eries,  Backup Chargers & more…
For Product Informaon, Operang Assistance, 
Parts, Owner’s Manuals, Dealer and Service info
go to  http://shop.panasonic.com/support
For the hearing or speech impaired TTY: 1- 877-833-8855  
As of June 2015   
						

							Limited Warranty (ONLY FOR U.S.A.)
16
For assistance, please visit http://shop.panasonic.com/supportAppendixHNC200_(en_en)_1005_ver.210.pdf   162015/10/06   13:23:03Limited Warranty Coverage (For USA Only)LaborOne (1) Year
Parts
One (1) Year
To submit a new repair request and for quick repair status visit our Web Site at http://shop.panasonic.com/support
Panasonic Products Limited Warranty
Online Repair Request
Mail-In Service--
Online Repair Request
If your product does not work properly because of a defect in materials or workmanship,  Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts,(b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by the warrantor. During the “Labor” warranty period there will be no charge for labor. During the “Parts”  warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet). This warranty only applies to products purchased and serviced in the United States.This warranty is extended only to the original purchaser of a new product which was not sold “as is”.
Home Network System Products
microSD card (Included model only) 90 days  N/A
When shipping the unit, carefully pack, include all supplied accessories listed in the Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box. When shipping Lithium Ion batteries please visit our Web Site at http://shop.panasonic.com/support as Panasonic is committed to providing the most up to date information. Include a letter detailing the complaint, a return address and provide a daytime phone number where you can be reached. A valid registered receipt is required under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL  BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Product or Part Name  
						

							For assistance, please visit http://shop.panasonic.com/support
17 AppendixHNC200_(en_en)_1005_ver.210.pdf   172015/10/06   13:23:03Limited Warranty Limits and Exclusions(As examples, this excludes damages for lost time, travel to and from the servicer,  loss of or damage to media or images, data or other memory or recorded content. The items listed are not exclusive, but for illustration only.)This warranty ONLY COVERS failures due to defects in materials or workmanship,  and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributable to acts of God. THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER  “LIMITED WARRANTY COVERAGE”.THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY,  ARE YOUR RESPONSIBILITY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Service Center. If the problem is not handled to your satisfaction, then write to:
                          Consumer Affairs Department
                          Panasonic Corporation of North Ame
rica
                          661 Independence Pkwy                                           Chesapeake, VA 23320
As of June 2015  
						

							18NotesHNC200_(en_en)_1005_ver.210.pdf   182015/10/06   13:23:03 
						

							For your future reference
We
 
recommend keeping a record of the following information to assist with any repair under
warranty.
Serial No. Date of purchase
(found on the bottom of the stand) Na m

e and address of dealer Attach your purchase receipt here.
 
  
HNC200_(en_en)_1005_ver.210.pdf   202015/10/06   13:23:04A BReconnect the AC adaptor to the camera.
If your product is not working properly. . .
IMPORTANT!
Visit our Web site: http://shop.panasonic.com/support 
• FAQ and troubleshooting hints are available.
Use the 
Home Network app  to access the User’s Guide 
and refer to the  Troubleshooting  section. Two Riverfront Plaza, Newark, NJ 07102-5490
© Panasonic System Networks Co., Ltd. 2014