Home
>
Panasonic
>
Car Satellite Radio System
>
Panasonic High Power Receiver Cr W400u Operating Instructions
Panasonic High Power Receiver Cr W400u Operating Instructions
Have a look at the manual Panasonic High Power Receiver Cr W400u Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 6
5
Fader
Press the knob to select the FADER mode and then turn it
clockwise or counterclockwise to shift the sound volume to the front
or rear speakers.
Mute
µPress [MUTE]to mute the sound completely.
µPress [MUTE]again to cancel.
Note: In the audio mode (BASS/TRE/BAL/FADE), the display
will return to regular operation mode when there is no input for
more than 5 seconds (2 seconds in the VOL mode).
or R 1 to 15Fader Center
Balance
Press the knob to select the BALANCE mode and then turn it
clockwise or...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-5.png "Page 6
5
Fader
Press the knob to select the FADER mode and then turn it
clockwise or counterclockwise to shift the sound volume to the front
or rear speakers.
Mute
µPress [MUTE]to mute the sound completely.
µPress [MUTE]again to cancel.
Note: In the audio mode (BASS/TRE/BAL/FADE), the display
will return to regular operation mode when there is no input for
more than 5 seconds (2 seconds in the VOL mode).
or R 1 to 15Fader Center
Balance
Press the knob to select the BALANCE mode and then turn it
clockwise or...")
![Page 7
6
Radio Basics
Selecting a Band
Press [BAND]to change the band setting as follows.
FM1
aFM2aW/BaAM
(Weather Band)
cd
ST indicator lights when FM stereo breadcast is available.
Manual Tuning
Press [TUNE j j]or [TUNE i i]to tune in a higher or lower
frequency.
Seek Tuning
Press and hold [SEEK j j]or [SEEK i i]for more than 0.5
seconds, then release it.
Seek tuning will automatically stop when a signal of the next
broadcast station is received.
CRW400U
CRW400U
CRW400U
CRW400U
Hold and release](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-6.png "Page 7
6
Radio Basics
Selecting a Band
Press [BAND]to change the band setting as follows.
FM1
aFM2aW/BaAM
(Weather Band)
cd
ST indicator lights when FM stereo breadcast is available.
Manual Tuning
Press [TUNE j j]or [TUNE i i]to tune in a higher or lower
frequency.
Seek Tuning
Press and hold [SEEK j j]or [SEEK i i]for more than 0.5
seconds, then release it.
Seek tuning will automatically stop when a signal of the next
broadcast station is received.
CRW400U
CRW400U
CRW400U
CRW400U
Hold and release")
![Page 8
7
Tuning in a Preset Station
Press the corresponding preset buttons [1]to [6]to tune in a preset
station.
Auto Station Preset
Select a band and press and hold [SCAN](AUTO PRESETS) for
more than 2 seconds.
µThe 6 strongest available stations will be automatically saved in
the memory on preset buttons
[1]to [6].µOnce set, the preset stations are sequentially scanned for 5
seconds each.
Notes:µIn Auto Station Preset mode, only FM2 is available for FM
stations. (FM1 is not available.)
µAuto Station Preset...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-7.png "Page 8
7
Tuning in a Preset Station
Press the corresponding preset buttons [1]to [6]to tune in a preset
station.
Auto Station Preset
Select a band and press and hold [SCAN](AUTO PRESETS) for
more than 2 seconds.
µThe 6 strongest available stations will be automatically saved in
the memory on preset buttons
[1]to [6].µOnce set, the preset stations are sequentially scanned for 5
seconds each.
Notes:µIn Auto Station Preset mode, only FM2 is available for FM
stations. (FM1 is not available.)
µAuto Station Preset...")
![Page 9
8
Tuning in a Weather Band
Station
Press any of the buttons [1]to [6]to monitor the preset station.
Weather Band Stations
National Weather Radio Broadcasts from over 380 locations
throughout the U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information 24
hours a day on one of the following frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 162.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Occasionally the frequency of an existing or planned station...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-8.png "Page 9
8
Tuning in a Weather Band
Station
Press any of the buttons [1]to [6]to monitor the preset station.
Weather Band Stations
National Weather Radio Broadcasts from over 380 locations
throughout the U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information 24
hours a day on one of the following frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 162.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Occasionally the frequency of an existing or planned station...")
![Page 10
CRW400UCRW400U
CRW400U
9
Clock Basics (The clock system is 12-hours.)
Initial Time
Press and hold [CLK]to set time. Display blinks, and the time
setting mode is activated.
Press
[i i]to set the hour.
Press
[j j]to set the minute.
(Hold
[i i]or [j j]to change numbers rapidly.)
Once the time has been set, release [CLK].
Note:When the clock is not set yet, SET is displayed.
Time Reset
When you want to reset the time, repeat steps and above.
Clock Display
Press [CLK]to display the current time.
Press...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-9.png "Page 10
CRW400UCRW400U
CRW400U
9
Clock Basics (The clock system is 12-hours.)
Initial Time
Press and hold [CLK]to set time. Display blinks, and the time
setting mode is activated.
Press
[i i]to set the hour.
Press
[j j]to set the minute.
(Hold
[i i]or [j j]to change numbers rapidly.)
Once the time has been set, release [CLK].
Note:When the clock is not set yet, SET is displayed.
Time Reset
When you want to reset the time, repeat steps and above.
Clock Display
Press [CLK]to display the current time.
Press...")
10 CRW400U In Case of Malfunction Reset Switch If the unit does not respond when the function buttons are pressed, press the reset switch with a small pointed object, such as a pencil point. This will restore the unit to its default settings. All previously stored memory settings will be erased. Repeat the necessary steps in the previous pages to reprogram the clock and memory settings. If pressing the reset switch does not restore normal operation, please return the radio to the nearest authorized service center for service.
11 Installation Guide This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers in attempting to install this product. Any attempt to install this product in a motor vehicle by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. WARNING ❏Overview This equipment should be installed by a professional. However, if you plan to install this unit yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to WARNING statement above) . µIdentify and label the vehicle wires.µConnect the vehicle wires to the wires of the power connector. µInstall the unit in the dash.µCheck the operation of the unit. If you do encounter problems, please consult your nearest authorized dealer. Caution:This unit will operate with a 12 volt DC negative ground auto battery system only. Do not attempt to use it in any other system. Doing so could cause serious damage. Before you begin installation, look for the following items included in the packing with your unit. µInstallation Hardware...... Needed for in-dash installation ❏Installation Hardware No. 1 Item Mounting Collar Diagram Qty
12 ❏Installation Procedures Note: Disconnect the cable from the negative (–) battery terminal. 1 Mounting CollarDashboard Mounting Tab Screwdriver 2. Secure the rear of the unit. a) Insert Power Connector to the unit. b) Check the electrical connection by referring to this operating instructions. c) Insert the unit into Mounting Collar and push it in until click is heard. Unit Power Connector8 1. Secure the Mounting Collar . Insert Mounting Collar into the vehicles dashboard, and bend mounting tabs out with a screwdriver. µWhen bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. µWe strongly recommend you to wear gloves for installation work to protect yourself from injuries.
13 To remove the unit from the vehicles dashboard Insert each removal tool and pull. Note: Do not lose removal tools. They will be needed to remove the unit from the vehicles dashboard. Removal tool (U-shaped)
14 Electrical Connections Cautions:µThis product is designed to operate with a 12-volt negative ground battery system.µTo prevent damage to the unit, be sure to follow the connection diagram below.µDo not insert the power connector into the unit until the wiring is completed.µBe sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and keep cable terminals free from touching any metal parts. (Rear Side) Dimmer Control Lead Connect to vehicle dimmer control lead (Red) ACC Ground(Black) (Yellow) Battery Dimmer(Orange w/White stripe) Power Connector (Violet) (Violet w/black stripe) (Gray w/black stripe) (Green) (Green w/black stripe) (White w/black stripe)(Gray) (white) Left Speaker (Front)Right Speaker (Front)Left Speaker (Rear)Right Speaker (Rear) Receiver CR-W400U Antenna Power Lead (ACC or IGN) To ACC power, +12V DC Ground Lead To a clean, bare metallic part of the vehicle chassis Battery Lead To the vehicle battery, continuous +12V DC
15 Troubleshooting ❏Maintenance Your product is designed and manufactured to ensure a minimum of maintenance. Use a soft cloth for routine exterior cleaning. Never use benzine, thinner, or other solvent. ❏Product Servicing If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized PASC service center. The unit should be serviced only by a qualified technician. ❏When Something Doesnt Work Check the charts on page 16 for possible causes and solutions to any problem you might be experiencing. Some simple checks or minor adjustments may eliminate the problem.
16 Troubleshooting (continued) ❏Troubleshooting Tips PROBLEM Unit does not turn on. Radio has static. Radio memory buttons do not work. Inverted sound (Left/Right conn- ections.) No sound from front or rear speakers POSSIBLE CAUSE Dead vehicle battery Ignition or Acc is not on. Bad power line connection Antenna not hooked up Close to high power lines Not holding buttons down long enough The speaker cords are inverted. The fader control is set on the wrong position. PROBABLE SOLUTION Charge vehicle battery. Turn ignition to On or Acc. Check connections. Hook up antenna. Move away from high power lines. Press and hold buttons for more than 2 seconds. Check the speaker cords. Adjust the fader control of the unit correctly.
17 Specifications General Power Supply : 12 V DC (11V-16V) Test Voltage 14.4V, Negative ground Maximum Power Output : 37W ×4 channels at 400 Hz, Volume Control maximum Power Output : 18W per channel into 4 ohms, 40 to 30,000Hz at 3% THD. Tone Action : Bass; ± 12 dB at 100 Hz Treble; ± 12 dB at 10 kHz Current Consumption : Less than 2.5 A (0.5W 4-speaker) Speaker Impedance : 4 Ω(4-8 Ωacceptable) Dimensions (W ×H ×D) : 7 ×1-15/16 ×5-7/8 (178 ×50 ×150 mm) Weight : 1 lbs. 14 oz. (0.85 k 5—) AM Radio Frequency Range : 530-1,710 kHz Useable Sensitivity : 28 dB/µV (25 µV/ S/N 20 dB) FM Stereo Radio Frequency Range : 87.9-107.9 MHz Useable Sensitivity : 12 dBf. (1.1 µV / 75Ω, S/N 30 dB) 50 dB Quienting Sensitivity : 17 dBf. (1.8 µV / 75Ω) Frequency Response : 30-15,000 Hz ± 3 dB Alternate Channel Selectivity : 75 dB Stereo Separation : 35 dB at 1,000 Hz Signal/Noise Ratio : 70 dB (Mono) Weather Band Radio Frequency Range : 162.40-162.55 MHz Useable Sensitivity : 3 dB/µV (S/N 20 dB) Signal/Noise Ratio (40 dB/µV) : 50 dB *Above specifications comply with EIA standards. Note: Specifications and design are subject to modification without notice due to improvements in technology. This unit has been manufactured under the Part 15 of the FCC Rules. Do not attempt to make any changes or modifications to this unit. Part 15 of the FCC Rules
Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America One Panasonic Way, Secaucus, New Jersey 07094 YFM284C337ZA TAMACO0900-0 Printed in Taiwan