Home
>
Panasonic
>
Car Satellite Radio System
>
Panasonic High Power Receiver Cr W400u Operating Instructions
Panasonic High Power Receiver Cr W400u Operating Instructions
Have a look at the manual Panasonic High Power Receiver Cr W400u Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 5
4
Power and Sound Controls
Power
If the vehicle is not running yet, turn the key in the ignition until the
accessory indicator lights.
Press
[PWR]to switch on the power.
Changing Audio Modes
Press this knob [SEL]to change the audio mode as follows.
VOLaBASSaTRE
(Volume) (Treble)
cdFADEbBAL
(Fader) (Balance)
Volume
µPress the knob to select the volume mode and then turn it
clockwise or counterclockwise to adjust the volume level.
Bass and Treble
Press the knob to select the BASS or TREBLE mode and then...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-4.png "Page 5
4
Power and Sound Controls
Power
If the vehicle is not running yet, turn the key in the ignition until the
accessory indicator lights.
Press
[PWR]to switch on the power.
Changing Audio Modes
Press this knob [SEL]to change the audio mode as follows.
VOLaBASSaTRE
(Volume) (Treble)
cdFADEbBAL
(Fader) (Balance)
Volume
µPress the knob to select the volume mode and then turn it
clockwise or counterclockwise to adjust the volume level.
Bass and Treble
Press the knob to select the BASS or TREBLE mode and then...")
![Page 6
5
Fader
Press the knob to select the FADER mode and then turn it
clockwise or counterclockwise to shift the sound volume to the front
or rear speakers.
Mute
µPress [MUTE]to mute the sound completely.
µPress [MUTE]again to cancel.
Note: In the audio mode (BASS/TRE/BAL/FADE), the display
will return to regular operation mode when there is no input for
more than 5 seconds (2 seconds in the VOL mode).
or R 1 to 15Fader Center
Balance
Press the knob to select the BALANCE mode and then turn it
clockwise or...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-5.png "Page 6
5
Fader
Press the knob to select the FADER mode and then turn it
clockwise or counterclockwise to shift the sound volume to the front
or rear speakers.
Mute
µPress [MUTE]to mute the sound completely.
µPress [MUTE]again to cancel.
Note: In the audio mode (BASS/TRE/BAL/FADE), the display
will return to regular operation mode when there is no input for
more than 5 seconds (2 seconds in the VOL mode).
or R 1 to 15Fader Center
Balance
Press the knob to select the BALANCE mode and then turn it
clockwise or...")
![Page 7
6
Radio Basics
Selecting a Band
Press [BAND]to change the band setting as follows.
FM1
aFM2aW/BaAM
(Weather Band)
cd
ST indicator lights when FM stereo breadcast is available.
Manual Tuning
Press [TUNE j j]or [TUNE i i]to tune in a higher or lower
frequency.
Seek Tuning
Press and hold [SEEK j j]or [SEEK i i]for more than 0.5
seconds, then release it.
Seek tuning will automatically stop when a signal of the next
broadcast station is received.
CRW400U
CRW400U
CRW400U
CRW400U
Hold and release](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-6.png "Page 7
6
Radio Basics
Selecting a Band
Press [BAND]to change the band setting as follows.
FM1
aFM2aW/BaAM
(Weather Band)
cd
ST indicator lights when FM stereo breadcast is available.
Manual Tuning
Press [TUNE j j]or [TUNE i i]to tune in a higher or lower
frequency.
Seek Tuning
Press and hold [SEEK j j]or [SEEK i i]for more than 0.5
seconds, then release it.
Seek tuning will automatically stop when a signal of the next
broadcast station is received.
CRW400U
CRW400U
CRW400U
CRW400U
Hold and release")
![Page 8
7
Tuning in a Preset Station
Press the corresponding preset buttons [1]to [6]to tune in a preset
station.
Auto Station Preset
Select a band and press and hold [SCAN](AUTO PRESETS) for
more than 2 seconds.
µThe 6 strongest available stations will be automatically saved in
the memory on preset buttons
[1]to [6].µOnce set, the preset stations are sequentially scanned for 5
seconds each.
Notes:µIn Auto Station Preset mode, only FM2 is available for FM
stations. (FM1 is not available.)
µAuto Station Preset...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-7.png "Page 8
7
Tuning in a Preset Station
Press the corresponding preset buttons [1]to [6]to tune in a preset
station.
Auto Station Preset
Select a band and press and hold [SCAN](AUTO PRESETS) for
more than 2 seconds.
µThe 6 strongest available stations will be automatically saved in
the memory on preset buttons
[1]to [6].µOnce set, the preset stations are sequentially scanned for 5
seconds each.
Notes:µIn Auto Station Preset mode, only FM2 is available for FM
stations. (FM1 is not available.)
µAuto Station Preset...")
![Page 9
8
Tuning in a Weather Band
Station
Press any of the buttons [1]to [6]to monitor the preset station.
Weather Band Stations
National Weather Radio Broadcasts from over 380 locations
throughout the U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information 24
hours a day on one of the following frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 162.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Occasionally the frequency of an existing or planned station...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-8.png "Page 9
8
Tuning in a Weather Band
Station
Press any of the buttons [1]to [6]to monitor the preset station.
Weather Band Stations
National Weather Radio Broadcasts from over 380 locations
throughout the U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information 24
hours a day on one of the following frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 162.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Occasionally the frequency of an existing or planned station...")
![Page 10
CRW400UCRW400U
CRW400U
9
Clock Basics (The clock system is 12-hours.)
Initial Time
Press and hold [CLK]to set time. Display blinks, and the time
setting mode is activated.
Press
[i i]to set the hour.
Press
[j j]to set the minute.
(Hold
[i i]or [j j]to change numbers rapidly.)
Once the time has been set, release [CLK].
Note:When the clock is not set yet, SET is displayed.
Time Reset
When you want to reset the time, repeat steps and above.
Clock Display
Press [CLK]to display the current time.
Press...](http://img.usermanuals.tech/thumb/58/65429/w64_cr-w400u_en_om_d-9.png "Page 10
CRW400UCRW400U
CRW400U
9
Clock Basics (The clock system is 12-hours.)
Initial Time
Press and hold [CLK]to set time. Display blinks, and the time
setting mode is activated.
Press
[i i]to set the hour.
Press
[j j]to set the minute.
(Hold
[i i]or [j j]to change numbers rapidly.)
Once the time has been set, release [CLK].
Note:When the clock is not set yet, SET is displayed.
Time Reset
When you want to reset the time, repeat steps and above.
Clock Display
Press [CLK]to display the current time.
Press...")
High Power Receiver CR-W400U Operating Instructions Please read these instructions carefully before using this product and save this manual for future use.
2 Panasonicwelcomes you to our ever growing family of electronic product owners. We know that this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family. ❏Use This Equipment Safely When Driving Keep the volume level low enough to be aware of road and traffic conditions. When Washing Vehicle Do not expose the equipment, including the speakers to water or excessive moisture. This could cause electrical shorts, fire or other damage. When Parked Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a chance to cool down before switching the unit on. Use the Proper Power Supply This equipment is designed to operate off a 12 volt, negative ground battery system (the normal system in a North American vehicle.) Use Authorized Service centers Do not attempt to disassemble or adjust this precision equipment. Please refer to the Service center list included with this product for service assistance. For Installation The product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30˚. Find the model number and serial number on either the back or bottom of the unit. Please record them in the space below and retain this booklet as a permanent record of your purchase to aid in identification in case of theft. MODEL NUMBER SERIAL NUMBER DATE PURCHASED FROMCR-W400U
3 Contents Use This Equipment Safely ...................................................................Page 2 ❏Power and Sound Controls ......................................................................4 How to adjust the volume, mute, balance, and tone for best listening ❏Radio Basics..............................................................................................6 Mode selection, manual and automatic tuning, band selection, preset stations ❏Clock Basics ..............................................................................................9 Setting the time, selecting the clock display ❏In case of Malfunction ............................................................................10 ❏Installation Guide ....................................................................................11 Step-by-step procedures, electrical connections ❏Troubleshooting ......................................................................................15 Troubleshooting tips, where to get service help Specifications .............................................................................................17 Part 15 of the FCC Rules ............................................................................17
4 Power and Sound Controls Power If the vehicle is not running yet, turn the key in the ignition until the accessory indicator lights. Press [PWR]to switch on the power. Changing Audio Modes Press this knob [SEL]to change the audio mode as follows. VOLaBASSaTRE (Volume) (Treble) cdFADEbBAL (Fader) (Balance) Volume µPress the knob to select the volume mode and then turn it clockwise or counterclockwise to adjust the volume level. Bass and Treble Press the knob to select the BASS or TREBLE mode and then turn it clockwise or counterclockwise to increase or decrease the bass / treble level. 0 to 40 -12 to 12-12 to 12 Volume Level CRW400U Anti-Volume-Blast Circuit At power on, the volume returns to the previous level slowly if the level was at 20 or higher. CRW400U CRW400U CRW400U CRW400U CRW400U d d
5 Fader Press the knob to select the FADER mode and then turn it clockwise or counterclockwise to shift the sound volume to the front or rear speakers. Mute µPress [MUTE]to mute the sound completely. µPress [MUTE]again to cancel. Note: In the audio mode (BASS/TRE/BAL/FADE), the display will return to regular operation mode when there is no input for more than 5 seconds (2 seconds in the VOL mode). or R 1 to 15Fader Center Balance Press the knob to select the BALANCE mode and then turn it clockwise or counterclockwise to shift the sound volume to the right or left speakers. or L 1 to 15Balance Center Power and Sound Controls(continued) (F: Front, R: Rear) Tone Enhancement (Loudness) µPress and hold [BAND](LOUD) for more than 2 seconds to enhance bass and treble tones when listening at low or medium volume. µPress and hold [BAND](LOUD) for more than 2 seconds again to deactivate when listening at higher volumes. CRW400U CRW400U Press and hold(R: Right, L: Left)
6 Radio Basics Selecting a Band Press [BAND]to change the band setting as follows. FM1 aFM2aW/BaAM (Weather Band) cd ST indicator lights when FM stereo breadcast is available. Manual Tuning Press [TUNE j j]or [TUNE i i]to tune in a higher or lower frequency. Seek Tuning Press and hold [SEEK j j]or [SEEK i i]for more than 0.5 seconds, then release it. Seek tuning will automatically stop when a signal of the next broadcast station is received. CRW400U CRW400U CRW400U CRW400U Hold and release
7 Tuning in a Preset Station Press the corresponding preset buttons [1]to [6]to tune in a preset station. Auto Station Preset Select a band and press and hold [SCAN](AUTO PRESETS) for more than 2 seconds. µThe 6 strongest available stations will be automatically saved in the memory on preset buttons [1]to [6].µOnce set, the preset stations are sequentially scanned for 5 seconds each. Notes:µIn Auto Station Preset mode, only FM2 is available for FM stations. (FM1 is not available.) µAuto Station Preset is not activated in Weather Band.µAny stations preset previously on the selected band will be erased. Radio Basics (continued) CRW400U d CRW400U CRW400U CRW400U CRW400U d Press and hold Manual Station Preset Press [BAND]to select a desired band.Use manual or seek tuning to find a station to be stored in the preset memory. Press and hold one of the preset buttons [1] to [6] until the display blinks once. Note:You can change the memory setting by repeating the above procedure. Preset Number CRW400U d Station Preset FM1, FM2 and AM can save maximum 6 stations each in their preset station memories. Caution:To ensure safety, never attempt to preset stations while you are driving.
8 Tuning in a Weather Band Station Press any of the buttons [1]to [6]to monitor the preset station. Weather Band Stations National Weather Radio Broadcasts from over 380 locations throughout the U.S. on seven VHF/FM frequencies. Tune to weather band to receive continuous weather information 24 hours a day on one of the following frequencies. 1. 162.550 MHz 2. 162.400 MHz 3. 162.475 MHz 4. 162.425 MHz 5. 162.450 MHz 6. 162.500 MHz 7. 162.525 MHz Occasionally the frequency of an existing or planned station must be changed because of unexpected radio frequency interference with adjacent NOAA Weather Radio Stations and/or with other Government or Commercial Operations within the area. If you have a question concerning NOAA Weather Radio, please contact your nearest National Weather Service Office. Note: The weather band (CH1-6) has been preset. CH7 is selected by pressing [j j]or [i i]. WBWeather Band Frequency Channel Number The frequency (162) remains unchanged.CRW400U
CRW400UCRW400U CRW400U 9 Clock Basics (The clock system is 12-hours.) Initial Time Press and hold [CLK]to set time. Display blinks, and the time setting mode is activated. Press [i i]to set the hour. Press [j j]to set the minute. (Hold [i i]or [j j]to change numbers rapidly.) Once the time has been set, release [CLK]. Note:When the clock is not set yet, SET is displayed. Time Reset When you want to reset the time, repeat steps and above. Clock Display Press [CLK]to display the current time. Press [CLK]again to return to previous display. Note: The current time will be displayed at all the time even the power of the radio is turned off. CRW400U CRW400U CRW400U d or CRW400U CRW400U