Panasonic High Definition Hospitality Plasma Display Th 37pr11 Operating Instructions

SERIAL
6789
1345
2
11
Connections
SERIAL Terminals connection
Notes:
•  Use the RS-232C straight cable to connect the computer 
to the Plasma Display.
•  The computer shown is for example purposes only.
•  Additional equipment and cables shown are not supplied  with this set.
The SERIAL terminal conforms to the RS-232C interface 
specifi  cation, so that the Plasma Display can be controlled 
by a computer which is connected to this terminal.
The computer will require software which allows the 
sending and...

POWER
12
Power ON / OFF 
Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug securely to the Plasma Display 
with the clamper. (see page 9) 
Connecting the plug to the Wall Outlet.
Note: 
When disconnecting the AC cord, be absolutely sure to disconnect 
the AC cord plug at the socket outlet fi rst.
Press the Power switch on the Plasma Display to turn the set on: 
Power-On. Power Indicator: Green
Press the  button on the remote control to turn the Plasma Display off.
Power Indicator:...

MENUENTER/INPUT
VOL
1/2
SIGNAL
PC
OFF
STANDBY SAVE OFF
POWER MANAGEMENTOFF
AUTO POWER OFF OFF
OSD LANGUAGE ENGLISH (
US )
COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL
POWER SAVE
SET UP
SCREENSAVER
13
Initial selections
Selecting the On-Screen Menu Language Selecting the input signal
Press to display the SET UP menu.
Press to select OSD LANGUAGE.
Press to select your preferred language.
  Selectable languages
Select the input signals to be connected by installing the optional Terminal Boards.
Press to select...

MENU
POWER
ENTER/INPUTVOL
14
Basic Controls
How to release button lock
MENU and ENTER/■ buttons are locked before 
shipping.
You can unlock them with unit buttons.
1. Press +/▲ 4 times.
2. Press INPUT 4 times.
3. Press –/▼  4 times.
4. Press ENTER/■.
Note:
After unlocking the buttons, Button lock in 
OPTIONS menu is set to “Off”. (see page 36) MENU Screen ON / OFF
This button is locked by initial setting.
Each time the MENU button is pressed, the 
menu screen will switch. (see page 20)
Power Indicator...

15
Basic Controls
POWER button
The Plasma Display must fi rst be plugged 
into the wall outlet and turned on at the 
power switch (see page 12).
Press this button to turn the Plasma 
Display On, from Standby mode. Press 
it again to turn the Plasma Display Off to 
Standby mode.
ACTION button
Press to make selections.
ASPECT button
Press to adjust the aspect. 
(see page 16)
POS. /SIZE button 
(see page 21)
PICTURE button  
(see page 22)
Sound mute On / Off  
Press this button to mute the sound.
Press again...

MENU ENTER/ INPUT 
VOL 
16
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its ma\
ximum size, including wide screen cinema format 
picture.
Press repeatedly to move through the aspect options:
For details about the aspect mode, please see “List of Aspect Modes” (page 41). 
Panasonic AUTO
The display will automatically become enlarged (depending on the pictur\
e source), allowing you to view the picture at its maximum size.
Panasonic AUTO41 6
39Notes:
• Panasonic AUTO...

A B  A B A B 
B A B A B A 
PC1 
VIDEO2 PC1 
VIDEO2 
VIDEO2 
VIDEO1 PC1 
VIDEO2 
A 
A 
A 
C B 
B 
B 
D 
17
Press repeatedly.
Each time pressing this button main picture and sub picture will be disp\
layed as follows below.
Press to swap main picture and 
sub picture.
Press to select the input mode.
Under main Picture and sub picture display, select the 
picture which you would like to change input modes.
Notes:
•  The sub picture sound is heard while a sub picture  operation is underway.
• The sub picture...

18
MULTI PIP
Advanced PIP
Notes:
•  If “INPUT lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.
•  Sound output is from the picture which is selected in Audio OUT (PIP) (see page 24).
•  In 2 screen display, the same input mode cannot be selected for the main picture and sub pi\
cture.
•  The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of the pictures. There may also be a difference in the picture...

MENU ENTER/ INPUT 
VOL 
2
EXIT
2
1
EXIT
× 1× 2× 3× 4
19
VOL button
Digital Zoom
This displays an enlargement of the designated part of the displayed ima\
ge.
Select the area of the image to be enlarged. Press on the enlargement location to select.
Return to normal display (quit Digital Zoom). Press to exit from the Digital Zoom.
Notes:
•  When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
•  The Digital Zoom function cannot be selected while in the following oper\
ation...

2/2 
ADVANCED SETTINGS  COLOR TEMP 
COLOR MANAGEMENT NORMAL 
OFF ON 
PICTURE 
0 
NORMAL NORMALIZE 
AUTO SETUP
POS. /SIZE 
V-POS 
0 
H-POS 
V-SIZE DOT CLOCK  H-SIZE 
CLOCK PHASE 
0 0 0 
0 
0 
0 
2.2 
BLACK EXTENSION 
AGC  GAMMA  INPUT LEVEL 
ADVANCED SETTINGS 
NORMAL NORMALIZE 
OFF 
1/2
SIGNAL
SET UP
PC
OFF
STANDBY SAVE OFF
POWER MANAGEMENTOFF
AUTO POWER OFF OFF
OSD LANGUAGE ENGLISH (
US )
COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL SCREENSAVER
POWER SAVE
2/2 SET UP 
SET UP TIMER
PRESENT TIME SETUP
0 
0 
0...