Panasonic Hdc Sdt750 Operating Instructions

							11VQT3B18
Accessories
Check the accessories before using this unit.
Keep the accessories out of reach of children to prevent swallowing.
Product numbers correct as of Aug. 2010. These may be subject to change.
Battery pack
VW-VBG130
AC adaptor
VSK0697
AC cable
K2CA2CA00025
DC cable
K2GJYDC00004
Remote control
(Built-in battery)
N2QAEC000024
AV multi cable
K1HY12YY0004
USB cable
K1HY04YY0032
HDMI mini cable
VFA0531
Stylus pen
VGQ0C14
Lens hood
VDW2053
Shoe adaptor
VYC0996
CD-ROM
Software3D Conversion Lens
Lens storage bag
VFC4619
Lens front cap
*
VYK4K64
Lens rear cap
*
VGQ0M57
* This is attached to the 3D Conversion  Lens at the time of purchase.
HDC-SDT750&TMT750-P-VQT3B18_mst.book  11 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							12VQT3B18
Quick Guide
∫Charging the battery
1 Connect the AC cable to the AC adaptor 
and the AC outlet.
2 Insert the battery into the AC adaptor by 
aligning the arrows.
∫Inserting the battery
Install the battery by inserting it in the 
direction shown in the figure.
A Insert the battery until it clicks and locks.
∫Inserting/removing an SD card
1) Open the LCD monitor.
≥Check that the access lamp has gone off.
2) Open the SD card/terminal cover and  insert (remove) the SD card into (from) 
the card slot.
≥ Face the label side  B in the direction 
shown in the illustration and press it 
straight in as far as it will go.
≥ Press the center of the SD card and then 
pull it straight out.
3) Securely close the SD card/terminal  cover.
≥ Securely close it until it clicks.
∫ Turning the unit on/off
Turning the unit on and off with the 
power button
Press the power button to turn on the unit.
A The status indicator lights on.
≥ To turn off the unit, hold down the power 
button until the status indicator goes off.
Turning the unit on and off with the LCD 
monitor/viewfinder
Opening the LCD monitor or extending the 
viewfinder turns on the unit. Closing the LCD 
monitor/viewfinder turns off the unit.
To turn on the unit
A The status indicator lights on.
Access lamp [ACCESS] A
≥
When this unit is accessing the SD 
card, the access lamp lights up.


Charging lamp 
[CHARGE]
A
Lights up:
Charging
Goes off:
Charging completed



HDC-SDT750&TMT750-P-VQT3B18_mst.book  12 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							13VQT3B18
To turn off the unit
BThe status indicator goes off.
∫Selecting a mode
Operate the mode dial to change the mode 
to ,  or .
∫How to use the touch screen
You can operate by directly touching the 
LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied) 
for detailed operation or if it is hard to 
operate with your fingers.
Touch and release the touch screen to select 
icon or picture.
∫Language selection
1) Press the MENU button, then touch 
[SETUP]  # [LANGUAGE].
2) Touch [English].
∫ Recording motion pictures
1) Change the mode to  .
2) Open the LCD monitor or extend the 
viewfinder.
3) Press the recording start/stop button to  start recording.
A When you begin recording,  ; changes 
to  ¥.
∫ Recording still pictures
1) Change the mode to  .
2) Open the LCD monitor or extend the 
viewfinder.
3) Press the   button fully to take the  picture.Motion Picture Recording 
Mode ( l31)
Still Picture Recording Mode 
( l 33)
Playback Mode ( l37, 90)

≥Align with the status indicator  A.
HDC-SDT750&TMT750-P-VQT3B18_mst.book  13 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							14VQT3B18
∫Motion picture/Still picture 
playback
1) Change the mode to  .
2) Touch the play mode select icon  A.
3) Select the [VIDEO/PICTURE] you wish  to play back.
≥ Touch [ENTER].
4) Touch the scene or the still picture to be  played back.
B  is displayed when [1080/60p] is 
touched or   is displayed when 
[AVCHD] is touched in step 3.
≥ Next (previous) page can be displayed by 
touching / .
5) Select the playback operation by  touching the operation icon.
COperation icon (Motion picture playback)
1
/;: Playback/Pause
6 : Rewind playback
5 : Fast forward playback
∫ : Stops the playback and shows 
the thumbnails.
1 : Displays the direct playback bar. 
(l 91)
(Still picture playback)
1 /;: Slide show (playback of the still 
pictures in numerical order) start/
pause.
2; : Plays back the previous picture.
;1 : Plays back the next picture.
∫ : Stops the playback and shows 
the thumbnails.
≥ Touch 
/ to display/not-display the 
operation icon.


F
0h00m00s 0h00m00s
0h00m00s

FF
HDC-SDT750&TMT750-P-VQT3B18_mst.book  14 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							15VQT3B18
Preparation
Before using
1
Parts identification and 
handling
1 Speaker
2 Power button [ ] (l25)
3 Inlet (cooling fan) ( l30)
4 Intelligent auto/Manual button  [iA/MANUAL] ( l35, 86)
5 Optical image stabilizer button  [ O.I.S.] ( l52)
6 Eyepiece corrector dial ( l28)
7 1080/60p button [1080/60p] ( l55)
8 Battery release lever [BATT] (l 20)
9 Battery holder ( l20)
10 DC input terminal [DC IN] ( l22)
≥ Always use the supplied AC adaptor or a 
genuine Panasonic AC adaptor 
(VW-AD21PP-K; optional).
11 HDMI mini connector [HDMI]  (l 104, 110)
12 USB terminal [ ] ( l113, 120, 133)
13 AV multi connector ( l104, 122)
≥ Use the AV multi cable (only the supplied 
cable).
14 Card slot ( l24)
15 Access lamp [ACCESS] ( l24)
16 Lens cover
≥The lens cover opens in   Motion 
Picture Recording Mode or   Still 
Picture Recording Mode. ( l26)
17 Multi manual ring ( l86, 89)
18 Camera function button  [CAMERA FUNCTION] ( l86)
19 Remote control sensor ( l50)
20 Built-in flash ( l65)
21 3D Conversion Lens attachment part  (concave) ( l56)
22 Lens (LEICA DICOMAR)
≥ Please refer to page 30 for details about 
attaching the lens hood.
23 AF assist lamp ( l85)
24 Recording lamp ( l45)
10
89
2
3 45 6
7 11
12
131
1415
16
17
18
19
20
22 21
23
24
HDC-SDT750&TMT750-P-VQT3B18_mst.book  15 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							16VQT3B18
25 LCD monitor (Touch screen) (l27)
≥ It can open up to 90 o.
≥ It can rotate up to 180 o A towards the lens 
or 90 o B  towards the viewfinder.
26 Viewfinder ( l28)
27 Quick menu button [Q.MENU] ( l41)
28 Sub recording start/stop button 
(l 30)
≥ This button functions in the same manner 
as the recording start/stop button.
29 Adjust zoom buttons ( l51)
30 Menu button [MENU] ( l40)
31 Delete button [ ] (l 99)
32 Tripod receptacle
2526
28
27 29 30 31
Due to limitations in LCD production 
technology, there may be some tiny bright 
or dark spots on the LCD monitor screen. 
However, this is not a malfunction and 
does not affect the recorded picture.
Due to limitations in LCD production 
technology, there may be some tiny bright 
or dark spots on the viewfinder screen. 
However, this is not a malfunction and 
does not affect the recorded picture.
32
HDC-SDT750&TMT750-P-VQT3B18_mst.book  16 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							17VQT3B18
33 Shoe adaptor mount (l166)
34 Shoe adaptor cover ( l166)
35 Shoe adaptor release lever  [SHOE ADAPTOR RELEASE] ( l166)
36 Photoshot button [ ] ( l33)
37 Zoom lever [W/T] (In Motion Picture  Recording Mode or Still Picture 
Recording Mode) (l 51)
Thumbnail display switch [ / ]/
Volume lever [ sVOL r] (In Playback 
Mode) ( l39)
38 Status indicator ( l25)
39 Internal microphones
40 Recording start/stop button (l 31)
41 Mode dial ( l26)
42 Shoulder strap fixture
43 Grip belt
Adjust the length of the grip belt so that it fits 
your hand.
1 Flip the belt.
2 Adjust the length.
3 Replace the belt.
44 Microphone terminal [MIC]
≥ A compatible plug-in powered microphone 
can be used as an external microphone.
≥ Audio will be stereo (2 ch) with the 
external microphone input.
≥ When the unit is connected with the AC 
adaptor, sometimes noise may be heard 
depending on the microphone type. In this 
case, please switch to the battery for the 
power supply and the noise will stop.
45 Headphone terminal [ ] ( l67)
MIC
33
34
35
39
3736
40 41 42 43 44
45
38
HDC-SDT750&TMT750-P-VQT3B18_mst.book  17 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							18VQT3B18
∫About the 3D Conversion Lens ( l56)
1 Attachment screw
2 Protective glass (front) 
3Lens
4 Adjustment dial cover
5 Vertical position adjustment dial 
[]
6 Vertical alignment adjustment dial 
[]
7 Horizontal image position adjustment  dial [ ]
8 Protective glass (rear) 
9 Camera body attachment part 
(convex)
Lens front cap
10 Horizontal line for adjustment
≥Use to adjust the lens attachment position.
≥ If you use the lens front cap as a stand as 
shown below, you can leave the unit with 
the 3D Conversion Lens attached. 
1
3 2
4
5
6
7
8
9
10
HDC-SDT750&TMT750-P-VQT3B18_mst.book  18 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							19VQT3B18
Preparation
Setup
1
Power supply
∫About batteries that you can use with this unit
The battery that can be used with this unit is VW-VBG130/VW-VBG260/VW-VBG6.
≥The unit has a function for distinguishing batteries which can be used safely. The 
dedicated battery (VW-VBG130/VW-VBG260/VW-VBG6) supports this function. The 
only batteries suitable for use with this unit are genuine Panasonic products and 
batteries manufactured by other companies and certified by Panasonic. (Batteries 
which do not support this function cannot be used). Panasonic cannot in any way 
guarantee the quality, performance or safety of batteries which have been 
manufactured by other companies and are not genuine Panasonic products.
≥
To use the VW-VBG6 for this unit, the battery  pack holder kit VW-VH04 (optional) is required.
Important:
If the DC cable is connected to the AC adaptor, then the battery will not charge. 
Remove the DC cable from the AC adaptor.
1Connect the AC cable to the AC adaptor and the AC outlet.
2Insert the battery into the AC adaptor by aligning the arrows.
It has been found that counterfeit battery packs which look very similar to the genuine 
product are made available to purchase in some markets. Some of these battery packs 
are not adequately protected with internal protection to meet the requirements of 
appropriate safety standards. There is a possibility that these battery packs may lead 
to fire or explosion. Please be advised that we are not liable for any accident or failure 
occurring as a result of use of a counterfeit battery pack. To ensure that safe products 
are used we would recommend that a genuine Panasonic battery pack is used.
Charging the battery
When this unit is purchased, the battery is not charged. Charge the battery before 
using this unit for the first time.
Charging lamp 
[CHARGE]A
Lights up:Charging (Battery charging time: l21)Goes off:
Charging completed
Flashing:
Be sure to connect the unit 
correctly. (l151)
HDC-SDT750&TMT750-P-VQT3B18_mst.book  19 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 
						

							20VQT3B18
≥We recommend using Panasonic batteries ( l11, 21, 164).
≥ If you use other batteries, we cannot guarantee the quality of this product.
≥ Do not heat or expose to flame.
≥ Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period 
of time with doors and windows closed.
Install the battery by inserting it in the direction shown in the figure.
Inserting/removing the battery
Removing the batteryBe sure to hold down the power 
button until the status indicator 
goes off. Then remove the battery 
while supporting the unit to prevent 
it from dropping.
Move the battery release lever in 
the direction indicated by the 
arrow and remove the battery 
when unlocked.
BATT
A Insert the battery until it clicks and 
locks.
CAUTION
Danger of explosion if battery is 
incorrectly replaced. Replace only with 
the same or equivalent type 
recommended by the manufacturer. 
Dispose of used batteries according to 
the manufacturer’s instructions.
HDC-SDT750&TMT750-P-VQT3B18_mst.book  20 ページ  ２０１０年８月２０日　金曜日　午後３時５３分