Panasonic Hdc Dx1 Operating Instructions

							81LSQT1093
Editing
4(Only when [SELECT] is selected in step 2)
Press the   button.
5When the confirmation message 
appears, select [YES], then press 
the cursor button.
(Only when [SELECT] is selected in step 2)
To continue deleting other scenes
Repeat steps 3-5.
To complete editing
Press the MENU button.
≥Scenes which cannot be played back (the 
thumbnails are displayed as [ ]) cannot be 
deleted.
≥Protected scenes cannot be deleted.
≥In case of [ALL SCENES], the deletion may 
take time if there are many scenes on the disc.
≥Do not turn off this unit while deleting.
≥When you delete scenes, use a battery with 
sufficient battery power or use the AC adaptor.
≥If you delete scenes recorded on other 
products with this unit, all the data related to 
the scenes may be deleted.
(RAM)
Scenes recorded on a disc can be protected so 
that they are not deleted by mistake.
(Even if you protect some scenes on a disc, 
formatting the disc will delete them.)
¬
Rotate the mode dial to select   
and then select the [ ] (motion 
picture playback) tab.
1Press the MENU button, then 
select [PLAY SETUP] 
# 
[SCENE PROTECT] # [YES] and 
press the cursor button.
2Select the scene to be protected 
and then press the center of the 
cursor button.
The [ ] indication appears and the scene is 
protected.
≥Press the cursor button again to cancel the 
setting.
≥2 or more scenes can be set in succession.
To complete the settings
Press the MENU button.
Protecting scenes
This is for preventing scenes from 
being deleted by mistake.
LSQT1093ENG.book  81 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							82LSQT1093
Editing
Editing still pictures
(SD)
The deleted files cannot be restored.
¬
Rotate the mode dial to select   
and then select the [ ] (still picture 
playback) tab.
1Press the   button during 
playback.
2When the confirmation message 
appears, select [YES], then press 
the cursor button.
¬Rotate the mode dial to select   
and then select the [ ] (still picture 
playback) tab.
1Press the   button while the 
thumbnail view screen is 
displayed.
2Move the cursor button up or 
down to select [SELECT] or 
[ALL SCENES] and press the 
cursor button.
≥When [ALL SCENES] is selected, all files 
on the SD card except the protected files 
will be erased. Proceed to step 5.
3(Only when [SELECT] is selected in step 2)
Select the file to be deleted, then 
press the cursor button.
The selected file is encircled by a red frame.
≥When the cursor button is pressed again, 
the selected file will be canceled.
≥Up to 50 files can be set in succession.
4(Only when [SELECT] is selected in step 2)
Press the   button.
Deleting still pictures
This is for deleting still picture files 
recorded on SD cards.
Deleting files one at a time
Deleting multiple files from the 
thumbnail display
LSQT1093ENG.book  82 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							83LSQT1093
Editing
5When the confirmation message 
appears, select [YES], then press 
the cursor button.
(Only when [SELECT] is selected in step 2)
To continue deleting other files
Repeat steps 3-5.
To complete editing
Press the MENU button.
ªDeleting still picture files 
recorded on an SD card by other 
products
A still picture file (other than JPEG) that cannot 
be played back on this unit may be erased.
≥Protected scenes cannot be deleted.
≥In case of [ALL SCENES], the deletion may 
take time if there are many files on the SD card.
≥Do not turn off this unit while deleting.
≥When you delete files, use a battery with 
sufficient battery power or use the AC adaptor.
≥Do not remove the SD card while deleting.
≥If files conforming to DCF standard are deleted, 
all the data related to the files will be deleted.
(SD)
Files recorded on an SD card can be protected 
so that they are not deleted by mistake. (Even if 
you protect some files on an SD card, formatting 
the SD card will delete them.)
¬
Rotate the mode dial to select   
and then select the [ ] (still picture 
playback) tab.
1Press the MENU button, then 
select [PLAY SETUP] 
# 
[SCENE PROTECT] # [YES] and 
press the cursor button.
2Select the file to be protected and 
then press the center of the 
cursor button.
The [ ] indication appears and the files is 
protected.
≥Press the cursor button again to cancel the 
setting.
≥2 or more files can be set in succession.
To complete the settings
Press the MENU button.
Protecting still pictures
This is for preventing still picture files 
from being deleted by mistake.
MENU
LSQT1093ENG.book  83 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							84LSQT1093
Editing
(SD)
You can write the data of the still pictures to be 
printed and the number of prints (DPOF data) 
onto the SD card.
¬
Rotate the mode dial to select   
and then select the [ ] (still picture 
playback) tab.
1Press the MENU button, then 
select [PLAY SETUP] 
# 
[DPOF SET] # [SET] and press 
the cursor button.
2Select the file to be set and then 
press the center of the cursor 
button.
The number of prints set to be in DPOF is 
displayed.
3Move the cursor button up or 
down to select the number of 
prints, then press the cursor 
button.
≥You can select from 0 to 999. (The selected 
number of pictures can be printed with the 
printer supporting DPOF.)
≥To cancel the setting, set the number of 
prints to [0].
≥You can also select multiple files in 
succession.
To complete the settings
Press the MENU button.
To cancel all DPOF settings
Press the MENU button, then select 
[PLAY SETUP] # [DPOF SET] # 
[CANCEL ALL] and press the cursor button.
≥When the confirmation message appears, 
select [YES], then press the cursor button.
ªWhat is DPOF?
DPOF stands for Digital Print Order Format. This 
enables picture printing information to be written 
onto an SD card so that it can be used on a 
system supporting DPOF.
≥The DPOF setting can be established for up to 
999 prints.
≥DPOF setting made on other devices may not 
be recognized by this unit. Please perform the 
DPOF settings on this unit.
≥You cannot add the recording date to pictures 
to be printed with the DPOF settings.
DPOF setting
This is for writing the printing data on 
an SD card.
MENU
LSQT1093ENG.book  84 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							85LSQT1093
Disc and card management
Disc and card 
management
Formatting
(RAM) (-RW)
Please be aware that if a disc is formatted, 
then all the data recorded on the disc will be 
erased.
¬
Rotate the mode dial to select   or 
rotate the mode dial to   and then 
select the [ ] (motion picture 
playback) tab.
1Press the MENU button, then 
select [SETUP] 
# 
[FORMAT DISC] # [YES] and 
press the cursor button.
2When the confirmation message 
appears, select [YES], then press 
the cursor button.
≥When formatting is complete, press the 
MENU button to exit the message screen.
≥Use this unit to format discs.
≥In the case of a double sided disc, format each 
side.
≥It may not be possible to format a disc with 
many scratches or dirt. Such discs cannot be 
used.
≥During formatting, do not turn this unit off.
≥When you format the disc, use a battery with 
sufficient battery power or the AC adaptor.
(SD)
Please be aware that if an SD card is 
formatted, then all the data recorded on the 
card will be erased. Store important data on a 
computer, etc.
¬
Rotate the mode dial to select   or 
.
1Press the MENU button, then 
select [SETUP] 
# 
[FORMAT CARD] # [YES] and 
press the cursor button.
2When the confirmation message 
appears, select [YES], then press 
the cursor button.
≥When formatting is complete, press the 
MENU button to exit the message screen.
≥Use this unit to format SD cards. If an SD card 
is formatted on other products (such as a 
computer), the time spent for recording may 
become longer and you may not be able to use 
the SD card.
≥Depending on the type of SD card being used, 
it may take time to format.
≥During formatting, do not turn this unit off.
≥When you format the SD card, use a battery 
with sufficient battery power or the AC adaptor.
≥Do not remove the SD card while formatting.
Formatting discs
This is for initializing discs.
MENU
Formatting an SD card
This is for initializing SD cards.
MENU
LSQT1093ENG.book  85 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							86LSQT1093
Disc and card management
Finalizing a disc
(-RW) (-R) (-R\DL)
If you insert a DVD-RW, DVD-R or DVD-R DL 
disc recorded in this unit (that has not been 
finalized) into another device such as DVD 
recorder, computer, etc., the disc may 
become unusable.
Be sure to finalize the disc on this unit before 
inserting it in other devices.
¬
Rotate the mode dial to select   
and then select the [ ] (motion 
picture playback) tab.
1Connect this unit to the AC 
adaptor.
≥Finalization cannot be executed when 
using a battery.
≥If the power supply stops while finalizing, 
the finalization will fail and the data may be 
damaged.
2Press the MENU button, then 
select [SETUP] 
# [FINALIZE] # 
[YES] and press the cursor 
button.
3When the confirmation message 
appears, select [YES], then press 
the cursor button.
≥When finalizing a DVD-RW, DVD-R or 
DVD-R DL a top menu containing 
thumbnails is created.
≥When finalizing is complete, press the 
MENU button to exit the message screen.
≥Do not finalize a disc recorded on this unit 
using any other device.
≥In the case of a double sided disc, finalize each 
side.
≥The top menu created when finalizing does not 
appear on this unit. It appears when the disc is 
played back on devices that support the 
AVCHD.
≥Depending on the condition of the disc, the time 
it takes for finalizing will differ. It may take up to 
17 minutes.
≥Do not allow the unit to be heavily vibrated or 
shaken while finalizing a disc. Doing so may 
prevent the disc from being finalized resulting 
in an unplayable disc. 
≥If the power supply stops while finalizing, the 
finalization will fail and the disc may become 
unplayable on other devices even if disc repair 
is carried out.
Finalizing a disc
This allows the discs to be played 
back on other devices that support 
the AVCHD.
Important Notice
Do not insert discs which have been 
recorded in AVCHD format into devices 
which do not support the AVCHD format. 
In some cases the disc may get stuck in 
the device. The disc will not play back on 
devices that do not support the AVCHD 
format.
DVD-RW, DVD-R and DVD-R DL:
≥After finalizing, the disc becomes play-only 
and you can no longer record.
≥When you un-finalize a DVD-RW, the disc 
can be used for recording again. (l87)
DVD-RAM:
≥It is not necessary to finalize DVD-RAM.
MENU
LSQT1093ENG.book  86 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							87LSQT1093
Disc and card management
(-RW)
¬Rotate the mode dial to select   
and then select the [ ] (motion 
picture playback) tab.
1Press the MENU button, then 
select [SETUP] 
# [UN-FINALIZE] 
# [YES] and press the cursor 
button.
2When the confirmation message 
appears, select [YES], then press 
the cursor button.
≥When un-finalizing is complete, press the 
MENU button to exit the message screen.
≥Discs other than DVD-RW cannot be 
un-finalized. If there is no space remaining on 
the DVD-RW, the disc may not be un-finalized.
≥When you un-finalize the disc, use a battery 
with sufficient battery power or the AC adaptor.
(RAM)
¬Rotate the mode dial to select   
and then select the [ ] (motion 
picture playback) tab.
1Connect this unit to the AC 
adaptor.
≥Creating a top menu cannot be executed 
when using a battery.
≥If the power supply stops while creating a 
top menu, the creating a top menu will fail 
and the data may be damaged.
2Press the MENU button, then 
select [SETUP] 
# 
[CREATE TOP MENU] # [YES] 
and press the cursor button.
3When the confirmation message 
appears, select [YES], then press 
the cursor button.
≥After creating the top menu, press the 
MENU button to exit the message screen.
≥If a top menu is created, the disc becomes 
play-only and you can no longer record.
≥The top menu that was created is not displayed 
on this unit. It is displayed when the disc is 
played back on other devices that support the 
AVCHD.
≥Except for DVD-RAM, the top menu is created 
during finalizing.
ªDeleting the top menuIf you insert a DVD-RAM on which a top menu 
was created, the confirmation message appears 
when you set a recording mode. If you select 
[YES] to erase the top menu, the DVD-RAM can 
be recorded and edited in the same way as 
before the top menu was created.
Un-finalizing a DVD-RW
This is for un-finalizing a DVD-RW so 
that it can be used for recording.
MENU
Creating a top menu
A top menu is displayed when a 
DVD-RAM is played back on other 
devices that support the AVCHD.
MENU
LSQT1093ENG.book  87 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							Disc and card management
88LSQT1093
Protecting a disc
(RAM) (-RW)
This is for protecting discs (write protection) when they are being ejected from this unit to prevent them 
from being formatted if they are inserted in other devices.
Discs protected using this unit cannot be edited or used to record on other devices, but they can be 
used in the same way as unprotected discs with this unit. 
Auto Protect Operation
≥After disc writing operations (recording motion pictures, editing, finalizing, un-finalizing, creating a top 
menu and deleting a top menu), the disc is protected when [AUTO PROTECT] is [ON], and it is not 
protected when [AUTO PROTECT] is [OFF].
≥When the protected disc is ejected, “WRITE PROTECTED DISC-CANNOT BE RECORDED BY 
OTHER DEVICES.” appears on the screen. 
Insert into 
unit >Operations on the unit >Status of ejected disc
 Protected disc
When auto 
protect is 
[ON]Motion picture recording, 
editing, etc.
 Protected
Playback only
 Unprotected 
discMotion picture recording, 
editing, etc.
Playback onlyUnprotected
 Protected disc
When auto 
protect is 
[OFF]Motion picture recording, 
editing, etc.
Unprotected
Playback only
 Protected
 Unprotected 
discMotion picture recording, 
editing, etc.Unprotected
Playback only
LSQT1093ENG.book  88 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							89LSQT1093
Disc and card management
¬Rotate the mode dial to select   or 
rotate the mode dial to   and then 
select the [ ] (motion picture 
playback) tab.
1Press the MENU button, then 
select [SETUP] 
# 
[AUTO PROTECT] # [ON] and 
press the cursor button.
≥This function’s default setting is [ON].
≥We recommend that the auto protect 
function is set to [ON] in order to prevent 
accidental deletion on other devices. If 
discs recorded on this unit are inserted into 
other devices without protecting them, a 
message may be displayed prompting you 
to format the disc. If the disc is formatted, 
the data on it will be erased, and the 
process cannot be reversed.
≥If a disc with no recorded motion pictures is 
ejected, it will not be protected.
ªTo release the disc protection
Erase all the motion pictures on the disc or 
format the disc.
≥Please be aware that if a disc is formatted, then 
all the data recorded will be erased and cannot 
be recovered.
≥The disc will need to be re-formatted on the 
device you will use.
Displaying disc information
(RAM) (-RW) (-R) (-R\DL)
Information such as the type of recorded disc, 
the number of recorded scenes, the remaining 
space and whether or not the disc is finalized is 
displayed.
¬
Rotate the mode dial to select   
and then select the [ ] (motion 
picture playback) tab.
Press the MENU button, then select 
[SETUP] 
# [INFORMATION] # [YES] 
and press the cursor button.
To exit the information screen
Press the MENU button.
MENU
MENU
LSQT1093ENG.book  89 ページ  ２００７年１月１５日　月曜日　午前９時２３分 
						

							90LSQT1093
With other products
With other products
With a TV
(RAM) (-RW) (-R) (-R\DL) (SD)
The motion pictures and still pictures recorded 
on this unit can be played back on a TV screen.
Connect this unit to a TV with one of the 
following terminals. When connecting to a 
HDMI terminal, a connection cable (optional) 
is necessary.
¬
Difference in picture quality 
depending on the terminal used for 
connection
AHigh quality
BStandard quality
CHDMI terminal
DComponent terminal
EVideo terminal
≥Do not use any other AV cables except the 
supplied one.≥Do not use any other component cables except 
the supplied one.
≥Use the AC adaptor to free you from worrying 
about the battery running down.
ªTo display the on-screen 
information on the TV
The information displayed on the screen 
(operation icon, time code etc.) can be displayed 
on the TV.
Press the EXT DISPLAY button on 
the remote control.
≥Press the button again to erase the information.
≥The screen on this unit will not change.
ªTo watch images with a 16:9 
aspect ratio on a regular TV (4:3)
When playing back motion pictures or still 
pictures recorded on this unit with a 16:9 aspect 
ratio on a TV with a 4:3 aspect ratio, the images 
on the screen may be squeezed horizontally. In 
this case, change the menu setting to play back 
the pictures in the original aspect ratio. 
(Depending on the TV setting, the pictures may 
not be displayed correctly. For more information, 
please read the operating instructions of your 
TV.)
Press the MENU button, then select 
[SETUP] 
# [TV ASPECT] # [4:3] and 
press the cursor button.
Example of images with a 16:9 aspect ratio on a 
regular TV (4:3)
Playback on TV
TV/Devices you useReference items
TV with a HDMI 
terminal1Connecting with 
a HDMI cable 
(optional) (l91)
TV with a HDMI 
terminal and AV 
amplifier with a 
HDMI terminal2Listening in 
5.1 channel 
sound (l93)
TV with a 
component terminal3Connecting with 
the component 
cable (supplied) 
and the AV cable 
(supplied) (l94)
Other TVs4Connecting with 
the AV cable 
(supplied) (l95)
A
CDEB
[TV ASPECT] setting
[16:9][4:3]
ZOOM START/
STOP PHOTO
SHOT EXT
DISPLAY
DATE/
TIME
VOL
LSQT1093ENG.book  90 ページ  ２００７年１月１５日　月曜日　午前９時２３分