Panasonic Hd Plasma Display Th 61phw6 Operating Instructions

11
PR/CR/RPB/CB/B Y/G
COMPONENT/RGB INAV  IN
VDHD
S VIDEO VIDEO RLAUDIORLAUDIOAUDIO
To tighten:
To loosen:
Push
the catch
Pull
Pull
PC    IN SERIAL
12
Connections / Cable fixing band
SPEAKER
Terminals (R)
– Cable fixing bands Secure any excess cables with bands, as required.
SPEAKER
Terminals (L)
From SERIAL Terminal on
Computer (see page 17)From EXIT monitor Terminal
on Computer
 (see page 15,16)
COMPONENT / RGB IN and Audio
IN Terminals
 (see page 13,14,16)
AV IN Terminals
(see page 12,13,16)
Pass the...

12
AV Input Terminals connection
Speakers connection
Two sets of speaker connections are provided for attaching 6 ohm speakers
to the display.
Refer to the manufacturers installation manual for your speakers for the
correct hook up procedure.
Luminance earth
Luminance inChrominance earth
Chrominance in
S VIDEO 4 pin socket
(S VIDEO VCR)
S VIDEO
Video input to
S VIDEO
socket Audio input to
L/R socketsAUDIO 2×RCA audio
cables
Audio
OUTVideo
OUTS Video
OUT
RL
AV  IN
S  VIDEO VIDEO RLAUDIO
Connect the signal...

13
COMPONENT / RGB Input connection
Component signals (Y, PB, PR ) connection
Connections
AV Input connection
VIDEO signal connection
Audio
OUTVideo
OUT
RL
AUDIO-VIDEOVideo input to
RCA socket
Audio input to
L/R sockets 3×RCA audio 
video cables
AV  IN
S VIDEO VIDEO RLAUDIO
(VCR)
PR/CR/RPB/CB/B Y/G
COMPONENT/RGB IN
VDHD RLAUDIO
RL Y
P
B
PR
AUDIO 3×RCA
video cables
2×RCA
audio cables
(DVD Player)
Y, PB, PR
Note:
Additional equipment and cables shown are not supplied with this set.
Notes:
(1) Change the...

14
Connections
Notes:
(1) Change the “COMPONENT / RGB-IN” setting in the “SET UP” menu to “RGB”. (see page 33)
(2) Additional equipment, cables and adaptor plugs shown are not supplied with this set.
COMPONENT/RGB IN
RLAUDIO
Audio input to
L/R sockets
G B R VD
HD
AUDIO
2×RCA audio cables 5×BNC
RGB cablesRGB input to 
R, G, B, HD, VD socketsBNC-RCA 
adaptor plug
Example of input signal source
HDTV-compatible VCR
Computer RGB camera
VDHDPR/CR/R
PB/CB/BY/G
RGB signal (R, G, B, HD, VD) connection
COMPONENT /...

15
Connections
PC Input Terminals connection
Notes:
(1) Computer signals which can be input are those with a horizontal scanning frequency of 15.5 to 110 kHz and vertical
scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200
lines.)
(2) The display resolution is a maximum of 1,024 × 768 dots when the aspect mode is set to “NORMAL”, and 1,366 × 768
dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it...

16
SERIAL PC    IN
AUDIO
PR/CR/RPB/CB/B Y/GCOMPONENT/RGB INAV  INVDHD
S  VIDEO VIDEO RLAUDIORLAUDIO
Signal Names for D-sub 15P Connector
Pin layout for PC input
terminal
1 678
39
45
1015 14 13 12 11
2
Connections
VIDEO / COMPONENT / RGB / PC input signals
AV (VIDEO, S VIDEO) inputCOMPONENT / RGB input
COMPONENT / RGB / PC input
PC RGB input
AV (VIDEO, S VIDEO) input
PC Input Terminals connection
Signal nameHorizontal Verticalfrequency(kHz) frequency(Hz)
1 NTSC 15.734 59.95
2 PAL 15.625 503 PAL60 15.734...

17
Connections
SERIAL Terminals connection
Notes:
(1) Use the RS-232C cable to connect the computer to the Plasma Display.
(2) The computer shown is for example purposes only.
(3) Additional equipment and cables shown are not supplied with this set.
SERIALRS-232C 
straight cable
D-sub 9p
COMPUTER
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by
a computer...

18
Power ON/OFF
Connecting the plug to the Wall Outlet
Press the POWER switch on the Plasma Display to turn the
set on POWER-ON.
Power Indicator: Green
Example: The screen below is displayed for a while after the
Plasma Display is turned on. (setting condition is
an example.)
Press the 
 
button on the remote control to turn the
Plasma Display off.
Power Indicator: Red (STAND-BY)
Press the 
 
button on the remote control to turn the
Plasma Display on.
Power Indicator: Green
To turn the power for the...

19
Select the Input Signal
R - STANDBY
G   POWER ON
TH-61PHW6INPUT—   VOL      +
—  VOL      +INPUT
Press the INPUT button to select the input
video signal desired from equipment such as
a VCR which has been connected to the
Plasma Display.
INPUT
SURROUND
VOL
NR
INPUT
INPUT
Power ON/OFF and Input Signal Selection
Input signals will change as follows:
For COMPONENT INPUT (see page 33)
For RGB INPUT (see page 32)
VIDEO          COMPONENT          PC
VIDEO          RGB          PC
Selecting the On-Screen...

20
PLASMA DISPLAY
INPUT
SURROUND
VOL
NR
PICTURE
SOUNDSET UP
ASPECT PICTURE
POS. /SIZE
OFF TIMER
PC
On-Screen Menu Display from Remote Control
To PICTURE POS./SIZE adjust
menu (see page 25)
During “VIDEO (S VIDEO)” and
“COMPONENT” input signal modes.
NORMALPICTURE  POS./SIZE
NORMALIZE
H-POS
H-SIZE
V-POS
V-SIZE
During “RGB” and “PC”
input signal modes.
NORMALPICTURE  POS./SIZE
NORMALIZE
H-POS
H-SIZE
V-POS
V-SIZE
CLOCK  PHASE
PICTURE
NORMALIZE
PICTURE  MENU
BRIGHTNESS
COLORSTANDARD
0
0
TINT
COLOR...