Panasonic Hd Integrated Camera Aw He2 Operating Instructions

							21VQT4N15
Ceiling-suspended Installation
When installing the camera by suspending it from the ceiling, be sure to attach the 
drop-prevention wire.
1Mount the stand to the ceiling using the M4 
screws (supplied).
≥ Tightening torque: 1.176 N·m (12 kgf·cm)
≥ Screw the stand’s three holes.
≥ Do not use any screws other than those supplied with the unit (do 
not use wood screws, nails, etc.).
≥ Make sure the stand is firmly mounted to the ceiling, with no tilting 
or wobbling.
≥ Screw the drop-prevention wire separately to the stand.
2Mount the drop-prevention wire to the ceiling 
by using the M4 screw (supplied) and the flat 
washer (for M4 screw, supplied).
≥Tightening torque: 1.176 N·m (12 kgf·cm)
≥ Pull the drop-prevention wire, and check that it has been 
attached securely.
≥ The drop-prevention wire is designed to be used for installation where the unit is 
suspended from an overhead surface so do not subject it to the weight of units other than 
the unit.
AW-HE2PPJPJYEEJEJY_PDF_mst.book  21 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							22VQT4N15
3Fix the camera to the stand.
1) Put the stand cover on the middle ring portion.
2) Loosen the horizontal fixing screw and insert the stand into the stand mounting hole.
3) Tighten the horizontal fixing screw and fix the camera to the stand.
≥Tightening torque: 1.176 N·m (12 k
gf·cm)
≥ Attach the camera securely with a prescribed tool.
≥ Adjust the horizontal orientation of the camera before fixing.
≥Tilt the camera horizontally and vertically as necessary for use. ( l10)
Standing Installation
Mount the stand/stand cover to the camera and install it. ( l10)
≥If you want to fix the stand, screw the stand to the 
installation surface with the M4 screws (supplied), and then 
mount the stand cover and the camera to the stand.
jTightening torque: 1.176 N·m (12 k
gf·cm)
≥ Place the unit such that it is horizontal to the installation surface.
≥ Install the unit in a stable location where there is no vibration. 
Vibration of the installation location causes image vibration.
≥ When installing the camera, take care that it does not fall, etc.
≥ Take care that the connected cables do not catch on something. 
If they do it may cause a fall or injury.

AW-HE2PPJPJYEEJEJY_PDF_mst.book  22 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							23VQT4N15
Mount to a Tripod
The tripod mounting hole of the unit supports 1/4-20UNC.
≥Loosen the horizontal fixing screw ( l10)
1Remove the stand fixing 
screw  A and spring washer 
B, and detach the stand 
protruding portion  C.
jThe stand protruding portion can be 
used as a tripod mounting hole.
2Insert the stand protruding portion in the 
stand mounting hole, and tighten the 
horizontal fixing screw.
≥Tightening torque: 1.176 N·m (12 kgf·cm)
3Mount a tripod to the tripod mounting hole  D.
≥Place the tripod on a completely flat and level surface.
≥ Tighten the screws by hand to mount the tripod securely.
≥ Do not install the unit where people will be passing back 
and forth.
≥ When using the unit mounted on a tripod, do not put the 
tripod high above the floor level.
≥ Mount the unit securely so there is no looseness. 
Looseness may cause the unit to fall off and/or result in 
injuries.
≥ When the unit is going to be used for a prolonged period 
of time, take steps to ensure that the unit will not topple or 
fall over and that it will not fall off or fall down. After using the unit, restore the installation 
location to its original state without delay.
∫ To return the stand to the condition it was in when you purchased it,
Use the stand fixing screw and spring washer to screw the stand protrusion to the stand.
≥Align the stand protruding portion and the stand correctly so that the stand protruding 
portion does not turn.
≥ Tightening torque: 2.94 N·m (30 k
gf·cm)





AW-HE2PPJPJYEEJEJY_PDF_mst.book  23 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							24VQT4N15
≥Connect the AC adaptor supplied with the unit, controller (AW-RP50) and compact live 
switcher (AW-HS50) to each device.
≥ Please use “High Speed HDMI Cables” that have the HDMI logo (as shown on the cover). 
Cables not conforming to the HDMI standar d will not work. Panasonic HDMI cable is 
recommended.
Part No.: RP-CDHS15 (1.5 m (4.9 ft.)), RP-CDHS30 (3.0 m (9.8 ft.))
≥ The unit is capable of transmitting IP images to only one terminal.
≥ If the unit is simultaneously controlled by more than one controller (AW-RP50), the unit 
may not function correctly.
Connections with an HD monitor
A HDMI cable:
An HDMI video/audio signal is output.
B Wireless remote controller (optional)
Connections with a controller (AW-RP50, optional)
AHDMI cable:
An HDMI video/audio signal is output.
B LAN cable:
A camera control sign is output.
C Controller (AW-RP50)
Installation Instructions
Connection with Other Devices




AW-HE2PPJPJYEEJEJY_PDF_mst.book  24 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							25VQT4N15
System example 1 (IP control)
: HDMI cable
: LAN cable
: Use an appropriate cable to suit the connected devices.
A HDMI/SDI converter
B Compact Live Switcher (AW-HS50)
C Personal computer
D Switching hub
E Monitor 1/Monitor 2
F Controller (AW-RP50)






AW-HE2PPJPJYEEJEJY_PDF_mst.book  25 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							26VQT4N15
System example 2 (IP control)
: HDMI cable
: LAN cable
: Use an appropriate cable to suit the connected devices.
A Switcher
B Personal computer
C Switching hub
D Monitor 1/Monitor 2
E Controller (AW-RP50)





AW-HE2PPJPJYEEJEJY_PDF_mst.book  26 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							27VQT4N15
For AW-HE2P
∫Product identification marking
Operating Instructions
Information for Your Safety
WARNING:
To reduce the risk of fire, electric shock or product damage,
≥Do not expose this unit to rain, moisture, dripping or splashing.
≥ Do not place objects filled with liquids, such as vases, on this unit.
≥ Use only the recommended accessories.
≥ Do not remove covers.
≥ Do not repair this unit by yourself. Refer servicing to qualified service personnel.
CAUTION!
To reduce the risk of fire, electric shock or product damage,
≥Do not install or place this unit in a bookcase, built-in cabinet or in another confined 
space. Ensure this unit is well ventilated.
≥ Do not obstruct this unit’s ventilation openings with newspapers, tablecloths, curtains, and 
similar items.
≥ Do not place sources of naked flames, such as lighted candles, on this unit.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting in personal injury.
CAUTION:
Do not pick up and move the unit while the tripod is attached.
The fitting may break under the weight of the tripod, which may result in injury.
Product Location
HD Integrated Camera Bottom
AC adaptor Bottom
Install this unit so that the power cord can be unplugged from the socket outlet immediately 
if any problem occurs.
AW-HE2PPJPJYEEJEJY_PDF_mst.book  27 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							28VQT4N15
THE FOLLOWING APPLIES ONLY IN THE U.S.A. AND CANADA.
Conforms to UL STD 60065
AC adaptor
This AC adaptor operates on AC between 100 V and 240 V.
But
≥In the U.S.A. and Canada, the AC adaptor must be connected to a 120 V AC power 
supply only.
≥ When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to 
suit the AC outlet configuration.
≥ When connecting to a supply of greater than AC 125 V, ensure the cord you use is suited 
to the voltage of the AC supply and the rated current of the AC adaptor.
≥ Contact an electrical parts distributor for assistance in selecting a suitable AC plug 
adaptor or AC cord set.
AW-HE2PPJPJYEEJEJY_PDF_mst.book  28 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							29VQT4N15
 indicates safety information.
THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC NOTICE (USA)
Declaration of Conformity
Model Number: AW-HE2P
Trade Name:
Panasonic
Responsible Party: Panasonic Corporation of North America  One Panasonic Way, Secaucus, NJ 07094
Support contact: 1-800-524-1448
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not 
make any unauthorized modifications.
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarant ee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference”
available from FCC local regional offices helpful.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation 
instructions and the user must use only shielded interface cables with ferrite core when 
connecting to host computer or peripheral devices. Also, any unauthorized changes or 
modifications to this equipment could void the user’s authority to operate this device.
NOTIFICATION (Canada)
This Class B digital apparatus complies with Canadian ICES-003.
AW-HE2P
AW-HE2PPJPJYEEJEJY_PDF_mst.book  29 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 
						

							30VQT4N15
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety 
instructions on the unit and the applicable safety instructions listed below. Keep these 
operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the 
manufacturer’s instructions.
8) Do not install near any heat sources  such as radiators, heat registers, 
stoves, or other apparatus (including 
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the  polarized or grounding-type plug. A 
polarized plug has two blades with one 
wider than the other. A grounding-type 
plug has two blades and a third 
grounding prong. The wide blade or the 
third prong are provided for your safety. 
If the provided plug does not fit into your 
outlet, consult an electrician for 
replacement of the obsolete outlet.
10) Protect the power cord from being  walked on or pinched particularly at 
plugs, convenience receptacles, and the 
point where they exit from the 
apparatus.
11) Only use attachments/accessories  specified by the manufacturer. 12) Use only with the 
cart, stand, tripod, 
bracket, or table 
specified by the 
manufacturer, or 
sold with the 
apparatus. When a 
cart is used, use caution when moving 
the cart/apparatus combination to avoid 
injury from tip-over.
13) Unplug this apparatus during lightning  storms or when unused for long periods 
of time.
14) Refer all servicing to qualified service  personnel. Servicing is required when 
the apparatus has been damaged in any 
way, such as power-supply cord or plug 
is damaged, liquid has been spilled or 
objects have fallen into the apparatus, 
the apparatus has been exposed to rain 
or moisture, does not operate normally, 
or has been dropped.
AW-HE2PPJPJYEEJEJY_PDF_mst.book  30 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分