Panasonic Hc V130 Owners Manual

							- 51 -
Motion picture playback using operation icon
For details on the basic playback operations, refer to page 24.
Advanced (Playback)
Playback Operations
Playback operationCursor button/Playback 
displayOperating steps
Slow-motion playback
During PauseWith the playback paused, press and hold 
1
 of the cursor button.
(Press and hold  2 for slow rewind 
playback)
Slow-motion playback will continue over the 
period that the button is pressed.
≥ Normal playback is restored when you press 
3.
≥ When Slow-motion pictures are played back 
in reverse, they will be shown continuously 
at approximately 2/3
rd the speed of normal 
playback (intervals of 0.5 seconds).
≥ Slow-motion playback for iFrame or MP4 
scenes will be in 1 second intervals.
Frame-by-frame 
playback With the playback paused, press 
1 of the 
cursor button.
(Press  2 to advance the frames one at a 
time in the reverse direction.)
≥ Normal playback is restored when you press 
3.
≥ When the frames are advanced one at a 
time in the reverse direction, they will be 
shown in intervals of 0.5 seconds.
≥ Frame-by-frame playback for iFrame or MP4 
scenes will be in 1 second intervals. 
						

							- 52 -
Creating still picture from motion picture
A single frame from the recorded motion picture can be saved as a still picture. (1920 k1080) still pictures will be recorded for the AVCHD scenes and iFrame scenes, and 
 (640 k360) still pictures will be recorded for the MP4 scenes.
Press the   button at the location to be saved as a still picture during the 
playback.
≥ It is convenient to use Pause, Slow-motion Playback and Frame-by-frame Playback.
≥ The date the motion picture was recorded will be registered as date of the still picture.
≥ Quality will be different from the normal still picture.
Repeat playback
Playback of the first scene starts after playback of the last scene finishes.
The   indication appears on the full screen views.
≥All the scenes are played back repeatedly. (When playing back motion pictures by date, all the 
scenes on the selected date are played back repeatedly.)
Resuming the previous playback
If playback of a scene was stopped halfway, the playback can be resumed from where it was 
stopped.
If playback of a motion picture is stopped,   appears on the thumbnail view of the stopped 
scene.
≥The memorized resume position is cleared if you turn off the unit or change the mode. (The 
setting of [RESUME PLAY] does not change.) : [VIDEO SETUP] 
# [REPEAT PLAY]  # [ON]
: [VIDEO SETUP]  # [RESUME PLAY]  # [ON]
2.1M0.2M 
						

							- 53 -
Zooming in on a still picture during playback 
(Playback zoom)
You can zoom in on still pictures during playback.
1Move the zoom lever to  side.≥You can zoom to a maximum of 4 a. (1 k #  2k  #  4k )
2Shift the position of the zoomed 
portion using the cursor button.
≥ The location of the zoom displays for about 
1 second when zooming in (zooming out) or 
moving the displayed location.
Zooming out from the zoomed still pictureMove the zoom lever to  side to zoom out. (4 k #  2k  #  1k )
≥ The more a picture is enlarged, the more its quality deteriorates.
RETURN   RETURN  
RETURN  
A Displayed location of the 
zoom 
						

							- 54 -
Playing back motion pictures/still pictures by date
The scenes or the still pictures recorded on the same day can be played back in succession.
1Select the date select icon using 
the cursor button, then press the 
ENTER button.
2Select the playback date, then press the ENTER button.The scenes or the still pictures recorded on the date selected are displayed as thumbnails.
3Select the scene or the still picture to be played back, then press the ENTER 
button.
≥Playing back of all the scenes or the still pictures returns if the unit is turned off or the mode is 
changed.
≥Even if the scenes have been recorded on the same day, they will be displayed separately 
in the following cases. -1, -2 ... are added after the date displayed on the list by date.
j When the number of scenes exceeds 99
j When recorded in Creative Control Mode
j When [NUMBER RESET] is performed
≥  is displayed after the date in the list by date for the still pictures created from the motion 
picture. ( l52)
Advanced (Playback)
Various playback functions
A Date select icon 
						

							- 55 -
Changing the playback settings and playing back the 
slide show
1Select   using the cursor button, 
then press the ENTER button.
2(Only when you would like to change the 
settings)
Select the item to change and press the ENTER button.
3(When [DATE SETUP] is selected)
Select the playback date, then press the ENTER button.
(When [SLIDE INTERVAL] is selected)
Select the interval of playback for the slide show and press the ENTER 
button.
(When [MUSIC SELECT] is selected)
Select the desired sound and press the 
ENTER button.
4Select [START] and press the ENTER button.
5Select the playback operation. (l24)≥When the playback is finished or stopped, the screen to select [REPLAY], 
[SELECT AGAIN] or [EXIT] is displayed. Select the desired item and press the ENTER button.
[DATE SETUP]:Select the date to be played back.
[SLIDE INTERVAL]:Selects the interval between still pictures at playback.
[MUSIC SELECT]:Select the music to be played on playback.
[SHORT]:Approx. 1 second
[NORMAL]:Approx. 5 seconds
[LONG]:Approx. 15 seconds 
						

							- 56 -
¬Change the mode to  .
∫ To delete the scene or still picture being played back
Press the Delete button while scenes or still pictures to be deleted are being 
played back.
∫To delete scenes or still pictures from the thumbnail display
≥Switch to the thumbnail display of the scenes or still pictures to delete. ( l24)
1Press the Delete button while the thumbnail view screen is displayed.≥When the thumbnail display is 1 scene display, the scene or still picture being displayed is 
deleted.
2Select [ALL SCENES], [MULTI] or 
[SINGLE] using the cursor button, then 
press the ENTER button.
≥All the scenes or still pictures displayed as 
thumbnails will be deleted by selecting 
[ALL SCENES].
(In case of playing back scenes or still pictures by date, all the scenes or still pictures on the 
selected date will be deleted.)
≥ Protected scenes/still pictures cannot be deleted.
Advanced (Playback)
Deleting scenes/still pictures
Deleted scenes/still pictures cannot be restored, so perform appropriate confirmation of 
the contents before proceeding with deletion. 
						

							- 57 -
3(When [MULTI] is selected in Step2)
Select the scene/still picture to be deleted, then press the ENTER button.
≥ The scene/still picture is selected and the  indication appears on the thumbnail. Press the 
ENTER button again to cancel the operation.
≥ Up to 99 scenes can be selected to be deleted.
(When [SINGLE] is selected in Step2)
Select the scene/still picture to be deleted, then press the ENTER button.
4(When [MULTI] is selected in Step2)
Select [Delete], and press the ENTER button, or the Delete button.
≥ To continuously delete other scenes/still pictures, repeat St eps 3-4.
When you stop deleting halfwayPress the MENU button while deleting.
≥The scenes or still pictures that have already been deleted when the deletion is canceled cannot 
be restored.
To complete editingPress the MENU button.
≥You can also delete scenes by pressing the MENU button, selecting [EDIT SCENE]  # [DELETE] 
#  [ALL SCENES], [MULTI] or [SINGLE].
≥ You can also delete still pictures by pressing the MENU button, selecting [PICT. SETUP]  # 
[DELETE]  # [ALL SCENES], [MULTI] or [SINGLE].
≥ Scenes which cannot be played back (the thumbnails are displayed as  ) cannot be deleted.
≥ In case of [ALL SCENES], the deletion may take time if there are many scenes or still pictures.
≥ If you delete scenes recorded on other products or still pictures conforming to DCF standard with 
this unit, all the data related to the scenes/still pictures may be deleted.
≥ When still pictures recorded on an SD card by other products are deleted, a still picture (other 
than JPEG) that cannot be played back on this unit may be erased. 
						

							- 58 -
Dividing a scene (AVCHD)
It is possible to divide an AVCHD scene. Any unwanted parts in the scene can be deleted after 
dividing.
≥Set the mode switch to  , select the play mode selection icon, and select the AVCHD 
scene. ( l24)
1Select the menu.
2Select the scene you wish to divide using the cursor button and press the 
ENTER button.
3Select  to set the dividing point.≥It is convenient to use Slow-motion Playback and 
Frame-by-frame Playback. ( l51)
≥ Select [YES] to continue dividing the same scene. To 
continue dividing other scenes, select [NO] and repeat 
St eps 2-3.
4Press the MENU button to complete dividing.≥Unwanted parts can be deleted. ( l56)
To delete all the divided points
≥The scenes that were deleted after division cannot be recovered.
≥You cannot divide a scene if the number of scenes of a given date would exceed 99 scenes.
≥ It may not be possible to divide scenes with a short recording time.
≥ Data that has been recorded or edited on another device cannot be divided and the divided points 
cannot be deleted. : [EDIT SCENE] 
# [DIVIDE] # [SET]
: [EDIT SCENE]  # [DIVIDE] # [CANCEL ALL]
0h00m15s0h00m15s0h00m15s 
						

							- 59 -
Dividing a scene to partially delete (iFrame, MP4)
Divide the iFrame or MP4 scene, and delete unnecessary parts.
This divides the recorded scenes in two and deletes the front half or back half.
The scenes that were deleted after division cannot be recovered.
≥Set the mode switch to  , select the play mode selection icon, and set to [iFrame] or 
[MP4]. ( l24)
1Select the menu.
2Select the scene you wish to divide using the cursor button and press the 
ENTER button.
3Select  to set the dividing point.≥It is convenient to use Slow-motion Playback and 
Frame-by-frame Playback. ( l51)
≥ Set to at least 2 seconds for the portions to be 
deleted and at least 3 seconds for the portion that is 
to remain.
4Select the part for deletion, then press the ENTER button.
5Select [YES] and press the ENTER button to confirm (play back) the part for 
deletion.
≥A confirmation message appears when [NO] is selected.
Proceed to St e p 7.
6Stop the playback.≥A confirmation message appears.
7Select [YES] and press the ENTER button.≥To continue dividing and deleting other scenes, repeat Steps 2-7.
To complete dividing≥Press the MENU button.
≥It may not be possible to divide scenes with a short recording time.
≥ The actual division may slightly slip off the previously designated dividing point. : [EDIT SCENE] 
# [SPLIT&DELETE]
0h00m15s 0h00m15s
0h00m15s 
						

							- 60 -
Protecting scenes/still pictures
Scenes/still pictures can be protected so that they are not deleted by mistake.
(Even if you protect some scenes/still pictures, formatting the media will delete them.)
≥Change the mode to  .
1Select the menu.
* [TRANSFER/PROTECT] is displayed when using the Eye-Fi card that is set as the selected 
transfer setting device in advance on the computer.
2Select the scene/still picture to be protected using the cursor button, then 
press the ENTER button.
≥The scene/still picture is selected and the   indication appears on the thumbnail. Press the 
ENTER button again to cancel the operation.
≥ Press the MENU button to complete the settings. : [VIDEO SETUP] or [PICT. SETUP] 
# [SCENE PROTECT]*