Panasonic Hc V130 Owners Manual

							- 21 -
≥Open the lens cover before turning on the unit. ( l6)
1Change the mode to   and 
open the LCD monitor.
2Press the   button.
≥ The still picture operating display ( ) will 
turn red while recording still pictures.
∫ About the screen indications in Still Picture Recording
≥During motion picture recording or when set to PRE-REC, you cannot record still pictures.
≥ Using a tripod is recommended when recording still pictures in dark places because the shutter 
speed becomes slow.
≥ The edges of still pictures recorded on this unit with a 16:9 aspect ratio may be cut at printing. 
Check the printer or photo studio before printing.
≥ Maximum number of recordable pictures that can be displayed is 9999. If the number of 
recordable pictures exceeds 9999, R 9999+ is displayed. The number will not change when the 
picture is taken until the number of recordable pictures is 9999 or less.
≥ The recording time may be long depending on the recording condition.
Basic
Recording still pictures
Size of still pictures ( l46)
R3000 Remaining number of still pictures
≥
 Flashes in red when [0] appears.
Still picture operation indicator ( l87)
R3000R3000R30008.9M
8.9M 
						

							- 22 -
The following modes (appropriate for the condition) are set just by pointing the unit to what you want 
to record.
≥Depending on the recording conditions, the unit may not enter the desired mode.
≥ In the Portrait, Spotlight and Low light mode, the face will be surrounded by white frame when 
detected. In the Portrait mode, a subject that is bigger and close to center of the screen will be 
surrounded by an orange frame. ( l45)
≥ Faces cannot be detected depending on the recording conditions, such as when faces are of 
certain sizes or at certain tilts or when digital zoom is used.
Basic
Intelligent Auto Mode
ModeEffect
Portrait Faces are detected and focused automatically, and the brightness 
is adjusted so it is recorded clearly.
SceneryThe whole landscape will be recorded vividly without whiting out 
the background sky, which may be very bright.
SpotlightVery bright object is recorded clearly.
Low lightIt can record very clearly even in a dark room or twilight.
NormalIn modes other than those described above, the contrast is 
adjusted to give a clear picture.
Intelligent auto/Manual buttonPress this button to switch Intelligent Auto 
Mode/Manual Mode (l47).
/MANUAL 
						

							- 23 -
∫
Intelligent Auto Mode
When switching to Intelligent Auto Mode, the Auto White Balance and Auto Focus operate and 
automatically adjust the color balance and focusing.
Depending on the brightness of the subject, etc., the aperture and shutter speed are automatically 
adjusted for optimum brightness.
≥Color balance and focus may not be adjusted automatically depending on light sources or 
scenes. If so, manually adjust these settings. ( l48, 50 )
Automatic White BalanceThe illustration shows the range over which Automatic White Balance functions.
1) The effective range of Automatic White Balance adjustment 
on this unit
2) Blue sky
3) Cloudy sky (rain)
4) Sunlight
5) White fluorescent lamp
6) Halogen light bulb
7) Incandescent light bulb
8) Sunrise or sunset
9) Candlelight
If the Automatic White Balance is not functioning normally, adjust 
the White Balance manually. ( l48)
Auto FocusThe unit focuses automatically.
≥Auto Focus does not work correctly in the following situations. 
Record pictures in the Manual Focus Mode. ( l50)
j Recording distant and close-up objects at the same time
j Recording a subject behind dirty or dusty window
j Recording a subject that is surrounded by objects with glossy surfaces or by highly reflective 
objects
4)
5)
6)
7)
8)
10 000K 9 000K
8 000K
7 000K
6 000K
5 000K
4 000K
3 000K
2 000K2)
1) 3)
9) 
						

							- 24 -
1Change the mode to  .
2Select the play mode select icon A 
using  3/4/2 and press the 
ENTER button.
≥ This can also be set from the menu.
[VIDEO SETUP] or [PICT. SETUP]  # [MEDIA, VIDEO/PICTURE]
3Select still picture B or motion picture  C to playback using  3/4/ 2/1 and 
press the ENTER button.
≥ If you press the MENU button, or select 
motion picture/still picture and press the 
ENTER button,  the setting is complete. 
≥ When a motion picture item is selected, an 
icon will appear on the thumbnail display. 
( ,   ,  )
4Select the scene or the still picture 
to be played back using  3/4/ 2/1, 
then press the ENTER button.
≥ When you select  / and press the 
ENTER button, the next (previous) page is 
displayed.
5Select the operation icon using 
3/4/ 2/1.
D Operation icon
≥ Press the ENTER button to display/not 
display the operation icon.
Basic
Motion picture/Still picture playback
NOV 15  2014
0h00m15s



NOV 15  2014
0h00m15s
0h00m00s0h00m00s0h00m00s
 
						

							- 25 -
* When pressed two times, the fast forward/fast rewind speed increases. (The screen display changes / .)
∫ Change the thumbnail display
While the thumbnail is displayed, the thumbnail display changes in the 
following order if the zoom lever is operated to   side or   side.
20 scenes  () 9 scenes  () 1 scene
≥ 9 scenes display returns if the unit is turned off or the mode is 
changed.
∫ Speaker volume adjustment
Operate the volume lever to adjust the speaker 
volume during motion picture playback.
≥Sound will be heard only during normal playback.
≥ If pause play is continued for 5 minutes, the screen returns to the thumbnails.
≥ The elapsed time for playback indication will be reset to 0h00m00s for each scene.
Motion picture playbackStill picture playback
1/ ;: Playback/Pause
6 : Rewind playback *
5 : Fast forward playback *
∫ : Stops the playback and shows the 
thumbnails. 1/
;: Slide show (playback of the still 
pictures in numerical order) start/
pa us e.
2; : Plays back the previous picture.
;1 : Plays back the next picture.
∫ : Stops the playback and shows the 
thumbnails.
Towards “ r”:Increases the volume
Towards “ s”:Decreases the volume
Motion picture compatibility≥ This unit is based on AVCHD format/MPEG-4 AVC file format.
≥ Even if the devices used have compatible standards, when playback of motion pictures 
recorded using another device is performed using this unit, or when motion pictures recorded 
using this unit is played back in another device, playback may not proceed normally, or may 
not be possible. (  is displayed for motion pictures that cannot be played back with this 
unit)
Please check compatibility in the operating instruction of your device.
≥ MP4 motion pictures that can be played back on this unit are limited to those recorded using 
this unit.
Still picture compatibility≥This unit is compliant with the unified standard DCF (Design rule for Camera File system) 
established by JEITA (Japan Electronics and Information Technology Industries Association).
≥ The file format of still pictures supported by this unit is JPEG. (Not all JPEG formatted files 
will be played back.)
≥ This unit may degrade or not play back still pictures recorded or created on other products 
and other products may degrade or not play back still pictures recorded on this unit. 
						

							- 26 -
1Press the MENU button.
2Press 3/4/2/1 to select the top 
menu  A, then press the ENTER 
button.
3Select the submenu  B using  3/4 
and press  1 or press the ENTER 
button.
4Select the desired item 
using  3/4/2/1 , and 
press the ENTER 
button to set. To get back to the previous screen
Press 
2 of the cursor button.
To exit the menu screenPress the MENU button.
∫ About the information display
Descriptions of the selected submenus and 
items displayed in St eps 3 and 4 are displayed.
∫About the operation icons
/:
Select and press the ENTER button to 
switch page. :
Select and press the 
ENTER button to 
return to previous screen.
Basic
Using the menu screen
0æ0ï0õ0æ0ó
0î0æ0ï0ö 
						

							- 27 -
Set the display method for the screen information display.
Please refer to page 62.
Please refer to page  17.
It is possible to display and record the time at the travel destination by selecting your home region 
and the travel destination.
≥ Change the mode to  .
1 Select the menu.
≥If the clock is not set, adjust the clock to the current time. ( l17)
≥ When the [HOME] (your home region) is not set, the message appears. Press the ENTER button 
and proceed to 
St e p 3.2 (Only when setting your home region)
Select [HOME] using 2/1 and press the ENTER button.
3 (Only when setting your home 
region)
Select your home region using 
2/1 and press the ENTER 
button.
≥ Press  3 to set daylight saving time. 
 is displayed and the summer 
time setting is turned on, the time 
difference between the current time and 
GMT will be set forward by 1 hour. 
Press  3 again to return to the normal 
time setting. If you set [Link Clock to Daylight Saving] to [ON], the current time will also be 
set forward by 1 hour. (l 28)
Basic
Using the Setup Menu
[DISPLAY]
: [SETUP]  # [DISPLAY] #  desired setting
[ON] (Display all information)/[OFF] (Display part of information)
[EXT. DISPLAY]
[CLOCK SET]
[SET WORLD TIME]
: [SETUP] # [SET WORLD TIME]


A The current time
B The time difference from GMT 
(Greenwich Mean Time) 
						

							- 28 -
4(Only when setting the region of your travel destination)
Select [DESTINATION] using 
2/1 and press the ENTER button.≥When the home region is set for the first time, the screen for selecting home/travel destination 
appears after setting the home region successively. If the home region has already been set 
once, execute the menu operation for Step 1.
5 (Only when setting the region of 
your travel destination)
Select your travel destination 
using 
2/1 and press the 
ENTER button.
≥Press 3 to set daylight saving time. 
 is displayed and the summer 
time setting is turned on, the time 
difference between the travel 
destination and the home region will be 
set forward by 1 hour. Press 
3 again to 
return to the normal time setting.
If you set [Link Clock to Daylight Saving] to [ON], the time at the travel destination will also 
be set forward by 1 hour.
≥ Close the setting by pressing the MENU button.   appears and the time of the travel 
destination is indicated.
To return the display to the home settingSet the home region using St ep 1 to 3, and close the setting by pressing the MENU button.
≥If you cannot find your travel destination in the area shown on the screen, set it by using the time 
difference from your home region.
If you set this function to [ON] and turn on the summer time setting in [SET WORLD TIME], the 
following times will be set forward by 1 hour: jWhen setting your home region: The current time
j
When setting the region of your travel destination: The local time at the selected travel destination
[Link Clock to Daylight 
Saving]
: [SETUP]  # [Link Clock to Daylight Saving] # desired setting
[ON]:The times are adjusted when the summer time setting is turned on.
[OFF]:The times are not adjusted when the summer time setting is turned on.


C The local time at the selected travel 
destination
D The time difference between the travel 
destination and the home region 
						

							- 29 -
It is possible to change the date and time display mode.
It is possible to change the date format.
When about 5 minutes have passed without any operation, this unit automatically turns off to save 
battery life.
≥This unit will not automatically turn off even if [ECONOMY (BATT)] is set to [ON] in following 
cases:
jUsing the AC adaptor
*
jUsing the USB cable for PC etc.
j PRE-REC is used
j During playback of the slide show
* When [ECONOMY (AC)] is activated, this unit automatically turns off.
When about 30 minutes have passed without any operation while connecting the AC adaptor with 
this unit, the unit automatically turns off.
≥ This unit will not automatically turn off even if the [ECONOMY (AC)] is set to [ON] in following 
cases:
jPRE-REC is used
j During playback of the slide show
[DATE/TIME]
: [SETUP]  # [DATE/TIME]  # desired setting
[DATE]/[D/T]/[OFF]
[DATE FORMAT]
: [SETUP]  # [DATE FORMAT]  # desired setting
 [Y/M/D]/[M/D/Y]/[D/M/Y]
[ECONOMY (BATT)]
: [SETUP] # [ECONOMY (BATT)]  #  [ON]
[ECONOMY (AC)]
: [SETUP]  # [ECONOMY (AC)]  # [ON] 
						

							- 30 -
This unit is put into recording pause approx. 0.6 seconds after the LCD monitor is reopened.
≥When in Quick Start Standby Mode about 60% of the power used in recording pause mode 
is being consumed, so the recording time will be reduced.
≥ Quick Start will not work if there is no SD card inserted.
≥ Change the mode to  .
1 Select the menu.
2 Close the LCD monitor.
The status indicator  A flashes green and the unit goes into 
Quick Start Standby Mode.
3 Open the LCD monitor.The status indicator  A lights red and the unit is put into 
recording pause.
≥ Quick Start Standby Mode is canceled if
jabout 5 minutes have elapsed
j mode is set to 
≥ It may take some time for Automatic White Balance to adjust.
≥ In the Quick Start Mode, the zoom magnification becomes approx. 1 k.
≥ When it has gone into Quick Start Standby Mode automatically with the [ECONOMY (BATT)] 
(l 29)/[ECONOMY (AC)] ( l29), close the LCD monitor once and open it again.
≥ Turn the unit off using the power button.
[QUICK START]
: [SETUP]  # [QUICK START] # [ON]

