Panasonic Full HD LCD Display TH 70LF50 Operating Instructions

							ON
POWER ON12 : 00VIDEO
SET UP TIMER 
DAY
POWER MODE
TIME
INPUT
TIMER FUNCTION PROGRAM1
MON PRESENT  TIME OF DAY  MON  0 : 03
31
SET UP TIMER
PRESENT TIME SETUP / SET UP TIMER
Set the program for turning the power ON/OFF and select the input signal at the speci ed time. Up to 20 programs can be set. 
[Setting Example]
Program 1, Every Monday,  12:00, Power On, Input: VIDEO
1
Set the program number.
2To execute the program, set to “ON”. 
The program is disabled when “OFF” is set.
 
3
Set the day.
The program is executed every day when “EVERYDAY” is 
se
t.
4
Set the power ON/OFF.
5Set the time.
Pressing “
” or “” button once changes “TIME” 1 minute.
Pressing “
” or “” button continuously changes “TIME” by 15 
minutes.
6Set the input.
Notes:
•  This function cannot be set unless “PRESENT TIME SETUP” is set.
•  If more than one programs are set for the same time, only the program with the smallest program number is enabled.
1 select
2 adjust 
						

							SCREENSAVER 
START 
MODEOFF
PRESENT  TIME OF DAY    MON 0 : 02
1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
32
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a SCREENSAVER should be used.
When the screen saver is operating, the following 5 patterns are displayed full screen for 5 seconds each. 
Black
Dark Gray
Gray
Light Gray
White
2 1
3
Press to display the SET UP menu.
Press to select the SCREENSAVER.
Press to select the SCREENSAVER screen.
MODE selection
START setting4
When the MODE is set to ON, press to select START.
Press to start SCREENSAVER.
The menu screen will disappear and the SCREENSAVER will be activated. To stop the 
SCREENSAVER under ON, press the R button or any buttons on the main unit. 
Note: When the display is turned off, the SCREENSAVER will be deactivated. Press to select the 
MODE.
Press to select each 
mode items.
SCREENSAVER (For preventing image retention)
Off
  
INTERVAL
  :  Operates when SHOW DURATION and SAVER 
DURATION are set up and those times arrive.
TIME OF DAY
  
:  Operates when START TIME and FINISH TIME 
are set up and those times arrive.
STANDBY AFTER SCR SAVER
  
:  Operates while SCREENSAVER DURATION, 
and display enters standby mode.
ON :  Operates when START is selected and the 
ACTION (
  ) button is pressed. 
						

							SCREENSAVER 
START 
MODE
FINISH TIME START TIMETIME OF DAY
6 : 15
12 : 30 PRESENT  TIME OF DAY    MON 15 : 00
SCREENSAVER 
START 
MODE
SAVER DURATION SHOW DURATIONINTERVAL
12 : 00
3 : 00 PRESENT  TIME OF DAY    MON 15 : 00
SCREENSAVER 
START 
MODE
SCREENSAVER DURATIONSTANDBY AFTER SCR SAVER6 : 15 PRESENT  TIME OF DAY    MON 15 : 00
2 1
3
1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
33
SCREENSAVER (For preventing image retention)
Setup of SCREENSAVER Time
After selecting TIME OF DAY, INTERVAL or STANDBY AFTER SCR SAVER, the relevant Time Setup will become available 
for selection and the Operating Time may be set. (Time cannot be set when “MODE” is “ON” or “OFF”.)
Automatically shifts the display image (therefore unnoticeable to the eye) to prevent image retention of sharper contour 
of image.Press to select START TIME / FINISH TIME (When TIME OF 
DAY is selected).
Press to select SHOW DURATION / SAVER DURATION (When 
INTERVAL is selected).
Press to select SCREENSAVER DURATION (When STANDBY 
AFTER SCR SAVER is selected).
Press to setup.
 
 button: Forward
   button: Back
Note: Timer function will not work unless “PRESENT TIME OF DAY” is set. Notes:
• Pressing “
” or “” button once changes the Time 1 minute.
 
[However, switching occurs every 15 minutes when Periodic Time is selected.]
• Pressing “” or “” button continuously changes the Time by 15 minutes.
•  “SCREENSAVER DURATION” of the “STANDBY AFTER SCR SAVER” can 
be set from 0:00 to 23:59. When this is set to “0:00”, “STANDBY AFTER SCR 
SAVER” will not be activated.
Press to display the SET UP menu.
Press to select “WOBBLING”.
Press to select “ON” or “OFF”.
ON:  Shifts the position of the display image on a  xed
 time 
interval.
Press to exit from adjust mode.
Notes:
•  If “MULTI DISPLAY SETUP” is set to “ON”, this function does not operate.
•  When this function is operating, part of the screen may appear to be missing. 
WOBBLING 
						

							1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
34
NO ACTIVITY POWER OFF
Press to select the menu to adjust.
Press to select “ENABLE” or “DISABLE”.
Press to exit from SET UP.
When this function is set to “ENABLE”, the power is turned off (standby) automatically when there is no operation of the 
Display for 4 hours.
Starting from 3 minutes before the turn off, the remaining time will be displayed. 
NO ACTIVITY POWER OFF
3MINPRESS ANY  KEY TO ABORT.
When the power is turned off due to this function, a message “LAST TURN OFF DUE TO ’NO ACTIVITY POWER 
OFF’.” is displayed next time the power is turned on.
Note:
  During the screensaver is running, this function is disabled.
1
2
3 
						

							1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
 
ECO MODE
CUSTOM: The menu of power consumption reduction is individually set.
ON:  The following  xed values are set to the menu of power consumption reduction. Individual setting is not available.
NO SIGNAL POWER OFF: ENABLE
PC POWER MANAGEMENT: ON
DVI-D POWER MANAGEMENT: ON
POWER SAVE: SENSOR
Using Remote Control
When  is pressed, the “ECO MODE” setting 
changes.ECO MODE  ON
Custom settings
The menu of the power consumption reduction is individually set. This setting is enabled when “ECO MODE” is set to 
“CUSTOM”.
NO SIGNAL POWER OFF
Equipment power supply is turned OFF when there is no signal.
When this is set to “ENABLE”, the power supply of the unit goes Off 10 minutes after the input signals stop.
Note: 
This function is effective during normal viewing (one picture screen).
PC POWER MANAGEMENT
When this function is set to ON, it operates under the following conditions to turn the power on or off automatically.
When no pictures are detected for 30 or so seconds during PC signal input:

 Power is turned off (standby); the power indicator lights up orange.
When pictures are subsequently detected:

 Power is turned on; the power indicator lights up green.
Notes:
• This function operates only during input from PC IN terminal.
• This function is effective when “SYNC” is set to “AUTO” and during normal viewing (one picture screen).
DVI-D POWER MANAGEMENT
When this function is set to ON, it operates under the following conditions to turn the power on or off automatically.
When no pictures (sync signal) are detected for 30 or so seconds during DVI signal input:

 Power is turned off (standby); the power indicator lights up orange.
When pictures (sync signal) are subsequently detected:

 Power is turned on; the power indicator lights up green.
Note: 
This function operates only during DVI signal input.
POWER SAVE
This function adjusts the brightness of the backlight to reduce power consumption.
OFF: This function does not operate.
ON: Backlight brightness is reduced.
SENSOR: The backlight brightness is automatically adjusted according to the viewing environment.
Note: 
When this function is set to “ON” or “SENSOR”, the “BACKLIGHT” setting in the PICTURE menu is disabled. 
1 select
2 adjust
ECO MODE SETTINGS
NO SIGNAL POWER OFFENABLE
OFFPOWER SAVE
DVI-D POWER MANAGEMENTOFF
PC POWER MANAGEMENTON
CUSTOM ECO MODE
35
ECO MODE SETTINGS 
						

							1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
Press to display the SETUP menu.
Press to select INPUT LABEL.
Press to display the INPUT LABEL screen.
Press to select image input.
Press to change input label.1
2
3
VIDEO
Component
INPUT LABEL
PCDVI
SLOT INPUT
HDMIVIDEO SLOT INPUT
Component
PC
DVI
HDMI
This function can change the label of the Input signal to be displayed. (see page 19)
Image input  Input label
[SLOT INPUT]*
1  SLOT INPUT / DVD1 / DVD2 / DVD3 /  Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
[VIDEO]  VIDEO / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
[Component]*
2  Component / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
[PC]  PC / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
[DVI]  DVI / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
[HDMI]  HDMI / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
(SKIP) : The INPUT button press will skip its input.
*1  “SLOT INPUT” is displayed when a Terminal Board is installed.
*2  “Component” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”.
 
(see page 40)
When a Terminal Board with dual input terminals is installed
“SLOT INPUT” is displayed as “SLOT INPUT A” and “SLOT INPUT B” and independent settings are available.
[SLOT INPUT A]  SLOT INPUT A / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
[SLOT INPUT B]  SLOT INPUT B / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
Customizing the Input labels
36 
						

							37
Press to display the SET UP menu.
Press to select OSD LANGUAGE.
Press to select your preferred language.
Press to display the SET UP menu.
Press to select “MENU DISPLAY DURATION”.
Press to adjust the display duration.
Press to select “MENU TRANSPARENCY”.
Press to adjust the transparency.
Press to exit from adjust mode.
   Selectable languages
English (UK)
Deutsch
Français
Italiano
Español
ENGLISH (US)
......(Chinese)
.......(Japanese)
.......(Russian)
Selecting the On-Screen Menu Language
1
1
4 2
2
3
1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
Customizing the On-Screen Menu Display
2/2 SET UP
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUPNETWORK SETUPMENU DISPLAY DURATION15 SMENU TRANSPARENCY20
Set the display time and background transparency of the on-screen menu display. 
						

							2/2SET UP
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUPNETWORK SETUPMENU DISPLAY DURATION15 SMENU TRANSPARENCY20
38
By lining up the Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across all 
screens.
For this mode of operation, each display has to be set up with a Display number to determine its location.
Press to select the MULTI DISPLAY SETUP.
Press to display the “MULTI DISPLAY SETUP” menu.
How to setup MULTI DISPLAY
group of 16 (4 × 4) group of 4 (2 × 2) group of 9 (3 × 3)
1 MULTI DISPLAY SETUP 
HORIZONTAL SCALE OFF 
A1
LOCATION VERTICAL SCALE 
BEZEL V ADJUSTMENT10BEZEL H ADJUSTMENT1
MULTI DISPLAY SETUP 
10
SET UP for MULTI DISPLAY
(Example)
group of 25 (5 × 5)
Press to display the SET UP menu.
1
2
3
Press to select the MULTI DISPLAY SETUP.
Press to select “ON” or “OFF”.
Item Details
MULTI DISPLAY SETUPSelect “ON” or “OFF”.
HORIZONTAL SCALESelect “1”, “2”, “3”, “4”, “5”.
VERTICAL SCALESelect “1”, “2”, “3”, “4”, “5”.
BEZEL H ADJUSTMENT
BEZEL V ADJUSTMENTAreas of the image that are hidden by the joint sections are adjusted both horizontally and vertically 
(0~100).
To show joints between displays. To hide joints between displays.
Suitable for still image display. Suitable for moving image display.
Setting value: 0 Setting value: 100 
						

							39
SET UP for MULTI DISPLAY
Item Details
LOCATIONSelect the required arrangement number. (A1-E5 : Refer to the following)
Display Number locations for each arrangement.
(Examples)
( 2 × 1) ( 2 × 3 ) ( 4 × 4 )( 4 × 2 ) ( 5 × 5 )
A1 A2 A3 A4 A5
B1 B2 B3 B4 B5
C1 C2 C3 C4 C5
D1 D2 D3 D4 D5
E1 E2 E3 E4 E5
Press to exit from adjust mode.4
You can set the remote control ID when you want to use this remote control on one of several different displays.
Note:
To operate this function, please purchase ID remote controller sold separately.
Object model : EUR7636070R
1
2
3Switch  to  on the right side.
Press the 
 button on the remote control.
Press one of 
 - ,  for the tens digit setting.
Press one of 
 - ,  for the units digit setting. 4
Notes:
•  The numbers in 2, 3 and 4 should be set up quickly.
•  Adjustable ID number range is 0 - 99.
•  If a number button is pressed more than two times, the  rst two numbers become the ID number 
for the remote control.
ID Cancellation
Press  button on remote control. (This has the same effect as pressing the , ,  buttons at the same time.)
Notes:
•  Set the Remote ID “On” to operate the ID remote control.
  If Remote ID is set to “On”, you can use the remote control without identical ID number during option menu display. 
  (see page 47)
•  The ID remote control cannot be used when ID select is set to anything other than 0, and the remote control ID is not 
the same as the ID select number (see page 47).
ID remote control button operation
The operation is the same as normal remote control except for the  button.
ID Remote Control Function 
						

							1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
40
SET UP for Input Signals
COMPONENT / RGB IN SELECT
Select to match the signals from the source connected to the COMPONENT/RGB IN terminal.
Y,  P
B, PR signals  “COMPONENT”
RGB signals 
 “RGB”
Press to display the SET UP menu.
Press to select the “COMPONENT / RGB-IN SELECT”.
Press to select the desired mode.
COMPONENT 
 RGB
Press to exit from adjust mode.
Note:
Make setting of the selected input terminal (COMPONENT/RGB IN).
1
2
3
1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
YUV/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
YUV / RGB IN SELECT
Select to match the signals from the source connected to DVI-D IN terminal.
YUV signals  
“YUV”
RGB signals 
 
“RGB”
Press to display the SET UP menu.
Press to select the “YUV / RGB-IN SELECT”.
Press to select the desired mode.
YUV 
 RGB
Press to exit from adjust mode.
1
2
3