Panasonic Full HD LCD Display TH 42AF1 Operating Instructions

111
Corresponding signalResolution (Dot) Scanning frequency
Dot clock 
frequency  (MHz) Format
*3Horizontal (kHz)
Vertical (Hz)
1 280 × 768 *
61 280 × 76839.6
49.965.3R/Y/D/H1 280 × 76847.760.080.1R/Y/D/H1 280 × 76847.859.979.5R/Y/D/H
1 280 × 800*61 280 × 80041.3
50.068.0R/Y/D/H1 280 × 80049.359.971.0R/Y/D/H1 280 × 80049.759.883.5R/Y/D/H
1 280 × 960*61 280 × 96060.0
60.0108.0R/Y/D/H1 280 × 96085.985.0148.5R/Y
1 280 × 1 024*61 280 × 1 02464.0
60.0108.0R/Y/D/H1 280 × 1 02480.075.0135.0R/Y/D/H1 280 × 1...

11 2
Note
●	 Remote control operation and external control 
command are not valid while  OpenPort PLATFORM 
system.
●	 When the power is turned on after  OpenPort 
PLATFORM system is shutdown and in standby 
condition (Power Indicator: Red), only < Standby (ON/
OFF) button> and “PON” command from SERIAL  
terminal are valid.
●	 The display may be greyed out in some conditions, 
such as when the OpenPort PLATFORM system is 
starting up. In this case, the OpenPort PLATFORM 
cannot be shut down.OpenPort...

11 3
Shipping condition
You can reset the settings / the adjusted values of the 
following menus to the factory settings:
[Picture], [Sound], [Setup], [ Position], [Options]
At the same time, resets the settings and the data of 
OpenPort PLATFORM to the factory settings and also 
deletes the applications you have installed.
 
■Remote control
1Press  to display the [ Setup] 
menu.
2Select [OSD language ] with   
and press  for more than 3 
seconds.
The following screen will be displayed.Options
Display...

11 4
Troubleshooting
Before you call for service, determine the symptoms and make a few simpl\
e checks as shown below.
SymptomsCheck
Picture Sound
Electrical Appliances
Cars / Motorcycles
Fluorescent light
InterferenceNoisy Sound
Normal 
PictureNo SoundVolume
(Check whether the mute function has been activated on the 
remote control.)
No PictureNo SoundNot plugged into AC outlet
Not switched on
Picture and Brightness/Volume setting
(Check by pressing the <
Main Power On / Off button> or the 
.)
No...

11 5
SymptomsCheck
No remote control operations can be performed. Check whether the batteries have discharged completely 
and, if they have not, whether they were inserted properly.
Check whether the remote control sensor is exposed to an 
outdoor light or a strong fluorescent light.
Check whether any obstacle is present between the remote 
control sensor and the remote control.
If the installation condition is normal, pull out the remote 
control sensor from the edge side of the main unit when 
using....

11 6
SymptomsCheck
Applications cannot be downloaded with  OpenPort 
PLATFORM. Check that the connection has been made properly. (see 
page 97)
Check that [WIRELESS & NETWORKS
] in OpenPort 
PLATFORM is set properly. (see page 55)
You can check the network-related setting information 
or [Check Communication ] in [STATUS] of OpenPort 
PLATFORM. (see page 52)
The application installed with  OpenPort 
PLATFORM does not operate, or the operation is 
unstable. Check that the home screen of OpenPort PLATFORM...

11 7
Specifications
Model No.
55-inch model:TH-55AF1U
49-inch model:TH-49AF1U
42-inch model:TH-42AF1U
55-inch model:TH-55AF1W
49-inch model:TH-49AF1W
42-inch model:TH-42AF1W
Power Consumption
55-inch model
190 W
49-inch model
175 W
42-inch model
155 W
Power off condition
0.3 W
Stand-by condition ●	 When [OpenPort PLATFORM standby] is set to 
[Off] (Factory default (TH-55AF1U, TH-49AF1U, 
TH-42AF1U))
0.5 W
Stand-by condition ●	 When [OpenPort PLATFORM standby] is set to 
[On] (Factory default (TH-55AF1W,...

11 8
OpenPort PLATFORM system
OSAndroid 4.4.3
CPU Cortex-A9, 1.0 GHz (quad)
Memory RAM 1 GB / ROM 8 GB
Supported codec Video:     MPEG4, H.264/AVC, H.263, MotionJPEG, 
MPEG2, WMV, VP8
Audio:  MP3, AAC, WMA, AMR, Ogg Vorbis
OpenPort PLATFORM part
USB (OpenPort PLATFORM)
USB connector × 3, TYPE A
USB2.0
Micro-USB Micro-USB connector, Micro-B
USB2.0
microSD card slot microSD, microSDHC
LAN For RJ45 network connections, compatible with 
PJLink
Communication method:RJ45 10BASE-T/100BASE-TX/1000BASE-T
Wireless...

11 9
Control terminals
SERIAL INExternal Control Terminal
D-sub 9 Pin:RS-232C compatible
SERIAL OUT External Control Terminal
D-sub 9 Pin:RS-232C compatible
IR IN Stereo mini jack (M3)
IR OUT Stereo mini jack (M3)
Sound
Built-in speakers80 mm × 30 mm × 2 pieces
Audio Output 20 W [10 W + 10 W] (10 % THD)
Remote Control Transmitter
Power sourceDC 3 V (battery (AAA/R03/UM4 type) × 2)
Operating range Approx. 7 m (22.9 ft)
(when operated directly in front of remote control 
sensor)
Mass Approx. 63 
 / 2.22 oz...

120
Software License
This product incorporates the following software:
(1) the software developed independently by or for Panasonic Corporati\
on,
(2) the software owned by third party and licensed to Panasonic Corpor\
ation,
(3) the software licensed under the GNU General Public License, Version 2.0 (GPL V2.0),
(4) the software licensed under the GNU LESSER General Public License,\
 Version 2.1 (LGPL V2.1), and/or
(5) open source software other than the software licensed under the GP\
L V2.0 and/or LGPL...