Panasonic Electronic Board UB-T880W, UB-T880W Operating Instructions

Installation Manual
41Operating Instructions
1
4.Install the wall mounting plates using the 4 screws.
•2 screws are used for each wall mounting plate. The remaining 4 screws are used after installing the 
elite Panaboard on the wall (page 50).
UB-T880 / UB-T880W•
Screws (8 count) are not included with the elite Panaboard. Please purchase screws with a size of M6, 
appropriate for your type of wall.
•Tighten the bolt so that it will not become loose.
•When drilling the holes and installing the wall...

Installation Manual
42Operating Instructions
Wall Types and Installation Procedures
The method for attaching the wall mounting plates to the wall will vary depending on the wall’s structure. 
Three available options are listed below.
Other methods may be necessary depending on the wall.
Metal or Concrete walls
Stud plugs (not included) are needed.
Drill bit
Metal or concrete wall
Insert a stud plug in the hole.
Stud plug
Wall mounting plate Drill 8 holes in the wall.
For the correct hole size, refer to...

Installation Manual
43Operating Instructions
1
Plasterboard walls
Split-wing toggles (not included) are needed.
Wooden walls
Wood screws (not included) are needed.
PlasterboardSplit-wing toggle
Arms Wall mounting 
plate
After the arms expand, pull the wall 
mounting plate out until the arms of the 
split-wing toggle grip firmly into the wall.
Tighten the bolt until the wall mounting plate 
is securely fixed into the wall.
Bolt
Insert the bolt through the hole in the wall 
mounting plate and into the hole...

Installation Manual
44Operating Instructions
Stand KX-B061 Assembly (Sold Separately)
Included Parts
Check that the following parts are included with the stand KX-B061.
*1Use the two-wing bolts (6) when securing the elite Panaboard to the stand.
*2The included wrench is necessary for tightening and loosening the screw ( 5), so keep it in a safe location.
No. Part Name IllustrationQ’ty
Stand Base 2
Support Beam 2
Cross Bar (A) 2
Cross Bar (B) 1
Screw (M6 ×  45 mm [1
3/4in.]) 10
Two-wing Bolt (M5 ×  12 mm...

Installation Manual
45Operating Instructions
1
CAUTION
Before assembly, be sure to lock the casters.
Assembly Instructions
1.Assemble the fall-prevention extension legs.
Locking the casters
(Push to lock)
UB-T880-PJQXC0337ZA_mst.book  45 ページ  ２０１０年５月１１日　火曜日　午後１時９分 

Installation Manual
46Operating Instructions
2.Assemble the stand.
Notice
•Do not over-tighten the screw (5). (Doing so can warp the support beams.)
•Assemble the stand so that the locking casters are on the rear side.
Assemble with the holes 
toward the front.
Locking 
caster side 
(rear)
REAR
Locking caster 
side (rear)
FRONT
UB-T880-PJQXC0337ZA_mst.book  46 ページ  ２０１０年５月１１日　火曜日　午後１時９分 

Installation Manual
47Operating Instructions
1
3.Pull the fall-prevention extension legs down.
Note
•When folding back the fall-prevention extension legs, release the lock as follows (1, 2).
4.Mount the elite Panaboard.
•See “Assembling the elite Panaboard” (For Mounting on a Stand KX-B061 (Sold Separately) 
→  page 52).
2
1
1
1
2
UB-T880-PJQXC0337ZA_mst.book  47 ページ  ２０１０年５月１１日　火曜日　午後１時９分 

Installation Manual
48Operating Instructions
Assembly Instructions
Preparing for Removing the elite Panaboard from Its Packaging
Remove the 10 joints, open the box, remove the accessory box & packing foam and open the plastic sheet of 
the elite Panaboard.
Notice
•When handling the electronic board, hold it by the edge frame and not the screen board. 
(Holding the screen board can result in damage.)
•The packing materials in the shipping box are necessary for repackaging, so keep them in a safe place....

49
Operating Instructions
Installation Manual
1
Assembling the elite Panaboard
For Wall Mounting
1.Attach the power cord.
•Connect the power cord to the elite Panaboard 
before installing on a wall.
2.Depending on the location of the outlet, install 
the power cord as illustrated in the following 
diagrams.
•When attaching the power cord downward.
•When attaching the power cord along the lower 
side of the elite Panaboard.
3.Remove the push-turn rivets (4) on the 
fasteners on the bottom of the board....

Installation Manual
50 Operating Instructions
5.Remove the screws on each end of the bottom 
of the lower frame cover.
•UB-T880: 2 screws, 
UB-T880W: 4 screws
(UB-T880 is shown in the following figure as an 
example.)
6.Open the pen tray, remove the screw caps and 
the screws, and remove the lower frame cover.
•Open the pen tray (1), and remove the right and 
left screw caps (2 locations). Then, remove the 
screws, and remove the lower frame cover ( 2).
Notice
•When removing the screw caps, hold them...